RepBox Wallmount by ruudboon

...repbox 2 wall mount by joshuabell thingiverse repbox wall mount

...e simple printable wall mount for the repbox https://www.repkord.com/products/repbox-2-the-3d-printing-spool-management-solution

...pbox exit fittings w/ ptfe connector by anicolaie thingiverse tools used to easily mount ptfe connector on repbox exit fittings.

...t that came with the repbox humidity kit. i used command strips to hang it on the inside under the top of the box for clearance.

...repbox pc4-m10 adapter with large hole thingiverse original design is great, but i think that the hole was too small.

... these ptfe caps for inside of the repbox when i have a tube without any filament in it:https://www.thingiverse.com/thing:2811279

...e i made this to plug the unused ptfe ports on my repbox2 for better air seal. it can be easily removed when changing filaments.

...ools in the repbox 2. for assembly instructions and the required hardware bits, please refer to the two upstream source projects.

...r bondtech prusa i3 mk3s upgrade to allow pg7 ptfe fittings to be attached directly. works great with palette 2s (pro) and repbox

...for the installation, follow the instruction from repbox:https://repkord.dozuki.com/guide/3-+optional+seal+kit+install/25?lang=en

...om scratch but inspired by the design of thijs van holstein. improved fitting and countersinked screws are the main improvements.

...e simple printable wall mount for the repbox https://www.repkord.com/products/repbox-2-the-3d-printing-spool-management-solution

...repbox 2 wall mount by joshuabell thingiverse repbox wall mount

...t that came with the repbox humidity kit. i used command strips to hang it on the inside under the top of the box for clearance.

...pbox exit fittings w/ ptfe connector by anicolaie thingiverse tools used to easily mount ptfe connector on repbox exit fittings.

...repbox pc4-m10 adapter with large hole thingiverse original design is great, but i think that the hole was too small.

...ools in the repbox 2. for assembly instructions and the required hardware bits, please refer to the two upstream source projects.

...e i made this to plug the unused ptfe ports on my repbox2 for better air seal. it can be easily removed when changing filaments.

...r 1 to 2 hours. history: 2019-10-14 - increased lid size by 1mm so it doesn't snap when removing 2019-10-07 - initial version

... the long silver nuts for the latch plate. adjust the plate as necessary. now you just need to find a seal and your good to go!!!

... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.

...l wallmounted bathroom sink for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1299967)

... wallmounted soap dispenser for download as max, 3ds, and obj on turbosquid: 3d models for games, architecture, videos. (1515993)

...mount signboard no.5 for download as blend, dae, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1576301)

...mount signboard no.4 for download as blend, dae, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1576296)

...mount signboard no.2 for download as blend, dae, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1576283)

...mount signboard no.1 for download as blend, dae, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1576282)

... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.

...ed bathroom sink vray faucet towel water soap wood accessory interior wallmounted bathroom sink 3d model plutonius 15557 3dexport

...roll and hill fiddlehead wallmount lamp 3ddd roll&hill roll and hill fiddlehead wallmount lamp