Thingiverse
Remote Control Modern Battleship
by Thingiverse
Last crawled date: 4 years, 2 months ago
This project began because I previously owned and crashed a remote control airplane. Having all the equipment necessary for radio control, it was time to make something less stressful to pilot and more likely to last!
Equipment recycled from the airplane includes:
Receiver (the chip that captures the radio signals and turns them into electricity)
ESC (or electronic speed controller, which connects the receiver to the motor)
Servomotor (controls the rudder)
Battery (11.1 volt LiPo)
Radio controller
Other equipment gotten from Amazon includes:
Drive shaft with 9.5mm sleeve (with the propeller and universal joint to connect to the motor)
Motor (D2030 brushless model)
1/4oz motor vehicle weights (to balance the boat)
Supplies, gotten from Walmart, include:
Rapid Fuse glue (to connect the parts)
Spray paint (the $1 one)
Household items like tape, knife, hanger wire, etc.
The print was made on the Monoprice Mini printer with PLA filament. The printer having a bed size of about 120mm wide by slightly more breadth, each part was cut to fit within those confines. With the printer wall line count being set at 2 and a 0.4mm thickness, each hull part took from 10 to 40 hours to print.
One thing learned from printing experience is that parts are best printed individually, instead of collectively. When the head must travel between parts at each layer, unwanted pieces of plastic get wasted on the edges, and the printer spends significant time traveling between parts instead of printing.
Another thing learned is that a minimum of 10% infill is required in order for the fill to hold together correctly. Looking back, it may be possible to print the hull without infill, increasing the rigidity of the outer wall instead; this could reduce the amount of time the printer zig-zags while increasing impermeability. However, my current model has the benefit of being stiff.
On small parts, like the tiller, I used 50% infill. This is absolutely necessary to keep the rod solidly attached to the control horn.
The Rapid Fuse glue works very well, binding strongly within 30 seconds. In fact, it may work a little too well, sticking the parts together before there is time to adjust them carefully. For future projects, cement glue, though a little more expensive, may be better, because it allows time for adjustments while fusing both pieces of plastic into one -- preventing possible leaks.
The ship took about three weeks of ongoing printing to complete. Some parts had to be re-printed because a setting caused them to print poorly. At any rate, as soon as the hull was finished, I painted it.
Equipment recycled from the airplane includes:
Receiver (the chip that captures the radio signals and turns them into electricity)
ESC (or electronic speed controller, which connects the receiver to the motor)
Servomotor (controls the rudder)
Battery (11.1 volt LiPo)
Radio controller
Other equipment gotten from Amazon includes:
Drive shaft with 9.5mm sleeve (with the propeller and universal joint to connect to the motor)
Motor (D2030 brushless model)
1/4oz motor vehicle weights (to balance the boat)
Supplies, gotten from Walmart, include:
Rapid Fuse glue (to connect the parts)
Spray paint (the $1 one)
Household items like tape, knife, hanger wire, etc.
The print was made on the Monoprice Mini printer with PLA filament. The printer having a bed size of about 120mm wide by slightly more breadth, each part was cut to fit within those confines. With the printer wall line count being set at 2 and a 0.4mm thickness, each hull part took from 10 to 40 hours to print.
One thing learned from printing experience is that parts are best printed individually, instead of collectively. When the head must travel between parts at each layer, unwanted pieces of plastic get wasted on the edges, and the printer spends significant time traveling between parts instead of printing.
Another thing learned is that a minimum of 10% infill is required in order for the fill to hold together correctly. Looking back, it may be possible to print the hull without infill, increasing the rigidity of the outer wall instead; this could reduce the amount of time the printer zig-zags while increasing impermeability. However, my current model has the benefit of being stiff.
On small parts, like the tiller, I used 50% infill. This is absolutely necessary to keep the rod solidly attached to the control horn.
The Rapid Fuse glue works very well, binding strongly within 30 seconds. In fact, it may work a little too well, sticking the parts together before there is time to adjust them carefully. For future projects, cement glue, though a little more expensive, may be better, because it allows time for adjustments while fusing both pieces of plastic into one -- preventing possible leaks.
The ship took about three weeks of ongoing printing to complete. Some parts had to be re-printed because a setting caused them to print poorly. At any rate, as soon as the hull was finished, I painted it.
Similar models
grabcad
free
Xiaomi Yi Bluetooth Remote Holder
...specific selfie stick from aliexpress.
it contains from two parts have made on 3d printer and connected with each other by glue.
thingiverse
free
Remote Control Ornithopter by aslobodn
... mod.
added a 2.4ghz receiver for use with a dsm2 radio system. rebuilt the main bird body with 3d printed parts and tissue paper
thingiverse
free
Motor controlled jalousie by fsvelim1
...ched to the jalousie control bar without any impact to the original control mechanism or window frame (except for a bit of glue).
grabcad
free
LEGO IR Receiver
...lego ir receiver
grabcad
takes signals from remote control and transmits to motors.
3dwarehouse
free
Remote
...remote
3dwarehouse
this is a simi-simple radio remote #control #parts #radio #rc #remote
3dwarehouse
free
Remote radio outpost (remote shack)
...a is secured,monitored, and controlled from your home shack. 73 de kc0qnb #amateur_radio #ham_radio #remotely_operated_radio_gear
thingiverse
free
Vuzix Falcore Bracket (Connex Falcore Drone Radio) by afterwords
...voltage step-down to make the connecter to power the receiver from the controller: https://www.amazon.com/gp/product/b0758zts61/.
thingiverse
free
RC Airboat Remix by birdofplay
...ot; to assist with alignment designed in.
hull settings per original
motor mount settings with added infill percentage and layers
grabcad
free
Core XY 3D printer
...ls will include an enclosure. the print head moves by employing two long timing belts, each of them connected to a stepper motor.
thingiverse
free
Remote Control Holder with Hook by flippmode
...ed 25%)
part 2 prints fine at 0.2mm layers, with supports. infill 10%+ (i used 25%)
printed on di3
feel free to modify as needed.
Battleship
turbosquid
$15
Battleship
...bosquid
royalty free 3d model battleship for download as max on turbosquid: 3d models for games, architecture, videos. (1187098)
turbosquid
$1
BattleShip
...bosquid
royalty free 3d model battleship for download as fbx on turbosquid: 3d models for games, architecture, videos. (1278616)
turbosquid
$50
Battleship
...oyalty free 3d model battleship for download as ige and sldpr on turbosquid: 3d models for games, architecture, videos. (1327165)
turbosquid
$40
Battleship
...d model battleship for download as ma, max, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1388446)
turbosquid
$19
Battleship
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$6
Battleship
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
battleship
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$65
battleship
...battleship
3dexport
simple rendering of the scene file
3d_export
$65
battleship
...battleship
3dexport
simple rendering of the scene file
3d_export
$65
battleship
...battleship
3dexport
simple rendering of the scene file
Remote
archibase_planet
free
Remote
...remote
archibase planet
tv remote remote controller remote
remote - 3d model for interior 3d visualization.
archibase_planet
free
Remote
...e
archibase planet
remote control remote controller remote
remote n140512 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$1
Remote
...
turbosquid
royalty free 3d model remote for download as obj on turbosquid: 3d models for games, architecture, videos. (1487515)
3d_export
$5
Tv Remote
...tv remote
3dexport
tv remote
3d_ocean
$7
Remote controller
... control switcher tv remote
remote controller for tv, sound systems etc easy to edit textures photo real rendered with mental ray
turbosquid
$39
remote
...free 3d model remote for download as obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1387531)
turbosquid
$5
remote
...free 3d model remote for download as 3ds, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1401849)
archive3d
free
Remote 3D Model
...l
archive3d
tv remote remote controller remote
remote - 3d model for interior 3d visualization.
turbosquid
$11
Remote
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
remote
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Control
3d_ocean
$4
Controller TQFP32
...qfp32
3docean
chip controller cpu electronic gpu mcu micro controller silicon smd tqfp wafer
a micro controller in tqfp32 package
3d_ocean
$4
Controller TQFP44
...44
3docean
chip controller cpu electronic gpu mcu micro controller package smd tqfp tqfp44
a micro controller in a tqfp44 package
3d_export
$15
control unit
...control unit
3dexport
control unit
3ddd
$1
Yacht control
...yacht control
3ddd
yacht control
3d_export
$5
controle pgdm
...controle pgdm
3dexport
carcaca controle pgdm
turbosquid
free
controler
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Control
...
http://www.schmitz-leuchten.de/html-ru/einzelleuchten-lampentyp-details.php?lamptype_no=700&group;=917&id;=731
3d_ocean
$4
Controller TQFP100
...100
3docean
chip computer cpu electronic gpu mcu micro controller pin platine silicon wafer
a micro controller in tqfp100 package
3d_ocean
$4
Controller TQFP64
...qfp64
3docean
chip computer cpu gpu mcu micro controller package silicon tqfp tqfp64 wafer
a micro controller in a tqfp64 package
3d_ocean
$7
Remote controller
... control switcher tv remote
remote controller for tv, sound systems etc easy to edit textures photo real rendered with mental ray
Modern
3d_export
$8
Modern pipo chair Modern furniture
...modern pipo chair modern furniture
3dexport
modern pipo chair. modern furniture
3d_export
$5
modern chair
...modern chair
3dexport
the modern chair for modern interior.
3ddd
$1
modern
...modern
3ddd
двери
коллекция modern
primavera-f, marilin, lago art
фабрика дверей папа-карло
3d_ocean
$19
Modern house
...modern house
3docean
architecture buildin house modern
modern house
3ddd
free
Modern bench
... bench , скамья , лавка
modern bench
3d_ocean
$25
Modern Bed
...modern bed
3docean
modern bed
3d_export
$20
modern sofas
...modern sofas
3dexport
modern sofas
3d_export
$20
modern sofas
...modern sofas
3dexport
modern sofas
3d_export
$20
modern sofas
...modern sofas
3dexport
modern sofas
3d_export
$20
modern sofas
...modern sofas
3dexport
modern sofas