Thingiverse
Remix of Spannerhands spool system
by Thingiverse
Last crawled date: 4 years, 2 months ago
This is my take on the beautiful and useful Spannerhands spool system.
Parts are collected from various things, modified by myself or newly created.
Two new features are:
detachable gelbox (no need to pour gel beads into or out of the cassette)
filament guide inside the PTFE coupler (filament doesn't get stuck when inserted)
Apart from printed parts you'll need:
2 x 608 bearings (id 8 mm od 22 mm)
12 x 10 mm M3 screws + nuts (locknuts adviseable)
1 x fitting for PTFE tube (with R1/8 male thread)
1 x PTFE tube
1 x 4.7cm x 2.7cm x 1.3cm hygrometer
No supports are needed unless suggested explicitly.
Print the following in PLA. I usually use 0.15 mm layer height in order to get the gutter for the flex seal smooth. In order to get the box reasonably air/moisture tight, I used 3 perimeters, 8 top and 6 bottom layers (for 0.15 mm).
1 x base (print with 10 mm brim!)
1 x lid (10 mm brim)
1 x hinge (can be printed horizontally without supports)
1 x hinge nut
2 x 608 bearing mount
1 x core
If you need a wall mount, you can choose between a mount screwed directly to the wall:
1 x wall mount
or a mount attached with sliding nuts to a 20 x 20 T-slot profile:
1 x 20x20 T slot mount
For some reason, I printed the following in orange PETG (again, think about thickness of perimeters and top + bottom):
1 x ptfe coupler
2 x clasp bracket
The seal should be printed in some very flexible material (92 ShA or less) and <= 10% infill:
1 x flex seal
The clasp, on the other hand, should be printed in a material with 98 ShA and 80% infill:
1 x semi flex clasp
Finally, I've modified the base to have a replaceable silica gel container which you need to print in PETG to withstand drying in a fruit and mushroom dryer without deformation. I would recommend to print it in clear PETG if you use silica gel with an indicator color such that you more easily can see the state of your gel. The gel box should be printed with the perforated side oriented downwards:
1 x gelbox2 (change orientation and use supports!)
1 x gelbox2-lid
Parts are collected from various things, modified by myself or newly created.
Two new features are:
detachable gelbox (no need to pour gel beads into or out of the cassette)
filament guide inside the PTFE coupler (filament doesn't get stuck when inserted)
Apart from printed parts you'll need:
2 x 608 bearings (id 8 mm od 22 mm)
12 x 10 mm M3 screws + nuts (locknuts adviseable)
1 x fitting for PTFE tube (with R1/8 male thread)
1 x PTFE tube
1 x 4.7cm x 2.7cm x 1.3cm hygrometer
No supports are needed unless suggested explicitly.
Print the following in PLA. I usually use 0.15 mm layer height in order to get the gutter for the flex seal smooth. In order to get the box reasonably air/moisture tight, I used 3 perimeters, 8 top and 6 bottom layers (for 0.15 mm).
1 x base (print with 10 mm brim!)
1 x lid (10 mm brim)
1 x hinge (can be printed horizontally without supports)
1 x hinge nut
2 x 608 bearing mount
1 x core
If you need a wall mount, you can choose between a mount screwed directly to the wall:
1 x wall mount
or a mount attached with sliding nuts to a 20 x 20 T-slot profile:
1 x 20x20 T slot mount
For some reason, I printed the following in orange PETG (again, think about thickness of perimeters and top + bottom):
1 x ptfe coupler
2 x clasp bracket
The seal should be printed in some very flexible material (92 ShA or less) and <= 10% infill:
1 x flex seal
The clasp, on the other hand, should be printed in a material with 98 ShA and 80% infill:
1 x semi flex clasp
Finally, I've modified the base to have a replaceable silica gel container which you need to print in PETG to withstand drying in a fruit and mushroom dryer without deformation. I would recommend to print it in clear PETG if you use silica gel with an indicator color such that you more easily can see the state of your gel. The gel box should be printed with the perforated side oriented downwards:
1 x gelbox2 (change orientation and use supports!)
1 x gelbox2-lid
Similar models
thingiverse
free
Rubbermaid 21 Cup Dry Box Spool Holder by Bradm10000
...
then feed filament through some ptfe tube in side
print
1 x screw
1 x nut
2 x mount
2 x bearing holder
requires
2 x 608 bearings
thingiverse
free
Dry Box Spool Holder by Bradm10000
...
then feed filament through some ptfe tube in side
print
1 x screw
1 x nut
2 x mount
2 x bearing holder
requires
2 x 608 bearings
thingiverse
free
SPANNERHANDS Spool Holder fit for 2,6 Kg Spools from dasfilament.de by Grinch82
...mehr umbauarbeiten erforderten spool core, ptfe coupler und 608 bearing mount. der ptfe coupler ist für ein m5 gewinde entworfen.
thingiverse
free
Fully Printed PTFE Bowden tube coupler for SPANNERHANDS spool holder. by jsondag
...upler for the spannerhands spool box without the need for the store bought fitting.
based on the bowden adapter made by daghizmo
thingiverse
free
PTFE Adapter for SPANNERHANDS Spool System by stonecoldfx
...egendary spannerhands filament wall mounted case!! (best thing out there in my opinion)
https://www.thingiverse.com/thing:2119644
thingiverse
free
Silica Gel Pot by krn
...ies with the round one.
updated again - large version - designed to hold much more silica gel and fit into the middle of a spool.
thingiverse
free
Sunlu FilaDryer S1 Frame Mount by JustaNormalGuy
...infill: 5 -10 %
perimeters: 4 - 5
mounting:
you will need 2x m5*40 screws and 2 drop-in t-nuts to securely mount it to the frame.
thingiverse
free
Camera house mount for Subsee +10 by hungtom2005
...diving house.
apart from the printing parts, you will need some screw and nuts
m3 35 mm x 3
m3 40 mm x 1
m3 nut x 4
m3 washer x 2
thingiverse
free
Torch Rail Mount by MakinBug
...r the stronger it will be.
you will need:
-1 x m3x 12-15mm bolt and 1 x m3 nut for each ring
-1 x m3x 30mm bolt
-1 x m3 nut
enjoy
thingiverse
free
Filament dehumidifier by JEpiston
...t any combination should fit together.
the stl files on the photo's are the smaller type so the silica male and silica female
Spannerhands
thingiverse
free
SPANNERHANDS SPANNERBOT MODEL by 3DMasterRace
...spannerhands spannerbot model by 3dmasterrace
thingiverse
spannerhands spanner bot
thingiverse
free
SPANNERHANDS 3D Logo by 3DMasterRace
...spannerhands 3d logo by 3dmasterrace
thingiverse
spannerhands 3d logo
thingiverse
free
SPANNERHANDS #SPANNERBOT by 3DMasterRace
...m:https://www.spannerhands.co.uk/samples-168-c.asp
spannerhands filllamanthttps://www.spannerhands.co.uk/175mm-filament-155-c.asp
thingiverse
free
Vice Jaws for Spannerhands
... spannerhands table vice: https://www.thingiverse.com/thing:1023913
it fits exact in the wholes of the vice.
best printed in tpu.
thingiverse
free
Spannerhands drybox core by Olorf
... spannerhands 50 mm core and an ingenious desiccant box for filament spools designed by https://www.thingiverse.com/jjlionberger/
thingiverse
free
Key for the spannerhands table vice
...e the screws for the spannerhands table vice more easily: https://www.thingiverse.com/thing:1023913
it fits exact on both screws.
thingiverse
free
Bracket Pins for SPANNERHANDS Spool by Kavex
...9;t have to use a m8 80mm threaded rod.
design: https://www.tinkercad.com/things/4u3omqnafig-bracket-pin-for-spannerhands-spool
thingiverse
free
Spannerhands all printable spool by samman946
...hem.https://www.thingiverse.com/thing:53451
spannerhands spool system can be found here:https://www.thingiverse.com/thing:2119644
thingiverse
free
hinge for Spannerhands Spool System by chriswal
...hinge for spannerhands spool system by chriswal
thingiverse
instead of the bolt a printed version of the hinge
thingiverse
free
MasterSpool V4 for SpannerHands Spool System by Dravpnir
... richrap modified to be easily used in the spannerhands spool system. idea came from chrizlle with his mod on the masterspool v3.
Spool
3ddd
$1
spool c53301
...spool c53301
3ddd
spool
spool c53301 650х350х145
turbosquid
$3
Cable Spool
...royalty free 3d model cable spool for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1457009)
turbosquid
free
Pallets and Spool
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Spool of String
...ol of string pink for download as c4d, 3ds, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1647892)
3ddd
$1
Подвесные светильники Spool
...ye/podvesnoy_svetilnik_spool_d320/ http://www.cosmorelax.ru/catalog/podvesnyye/podvesnoy_svetilnik_spool_d420/
3ddd
free
Spool 001 sofa
...spool 001 sofa
3ddd
roda
roda
collection spool
design rodolfo dordoni
dimensions:
lenght 90 cm
depth 94 cm
height 79 cm
turbosquid
$15
Roda Spool Sofa
...ee 3d model roda spool sofa for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1502650)
turbosquid
$95
wire spools 3ds
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
spool of TV wire
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$3
Simple and Fast Spool Holder
...ree 3d model simple and fast spool holder for download as stl on turbosquid: 3d models for games, architecture, videos. (1548546)
Remix
turbosquid
$5
MODA Collection Remix Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$12
remix yamaha rm1x
...remix yamaha rm1x
3dexport
geometry triangles 15.2k vertices 7.6k pbr no textures 1 materials 1 uv layers yes
3d_ocean
$5
Vray fabric Kvadrat remix green - tileable
...th vray and 3dsmax. high-resolution texture images (2000×2000 px) file included: shader vray 2.40 texture image 3ds max 2011 file
turbosquid
$20
Gerrit Rietveld 1938 Zig Zag Chair Remix
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$10
multicolored remix parametric table furniture
... fbx, obj, mtl, archive with textures. the model has no glitches. render and materials - vray . without using plugins. good use!
3ddd
$1
Barovier&Toso / Manhattan Remix 7192
... 004293-142405
в коллекции есть люстры 7, 9, 12 рожковые. диаметр соответственный 1000, 1250, 1500 мм.
3ddd
$1
Muuto fiber chair
...grey/grey, dusty green/dusty green, nature/oak, natural white/oak upholstery options remix 183/black, remix 133/grey, remix 643/dusty red leather options black...
3ddd
$1
Barovier&Toso 7190-7195
...7190-7195 3ddd barovier&toso потолочнай люстра фабрики barovier&toso;, коллекция manhattan remix артикул 7190-7195. размеры в inches: 39"...
3d_export
$5
3D Locking Handle Weatherproof Storage Box Container
...handle weatherproof storage box container 3dexport new, improved and remixd! no screws required. print-in-place. weatherproof. parametric. 2 parts. easy...
cg_studio
$49
HTC One Mini 2 Amber Gold3d model
...cell phone mobile cellular super lcd touchscreen touch screen remix amber gold .max .obj .mb .lwo .fbx .c4d .3ds...
System
archibase_planet
free
System
...m
archibase planet
fire alarm system fire alarm box
security light system - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spider system
...stem spider glass system
spider system to fix glass stefano galli n050912 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
Euforia System
...euforia system
3ddd
euforia
euforia system
3d_export
$50
Roof system Truss system 3D Model
...oof system truss system 3d model
3dexport
roof system truss truss stage
roof system truss system 3d model aleksbel 38970 3dexport
3ddd
$1
DVD System
...dvd system
3ddd
dvd , schneider
dvd system
design_connected
free
Seating system
...seating system
designconnected
free 3d model of seating system
3d_export
$5
solar system
...solar system
3dexport
solar system in c4d, with 8k nasa textures
3ddd
$1
Quanta System
...quanta system
3ddd
медицина
quanta system.
лазерное оборудование для медицинских центров
3d_export
$15
solar system
...nd the other the sun, the earth and the moon, the latter has an animation with camera movement included, the files are in spanish
3d_export
$14
missile system
...missile system
3dexport