Thingiverse
RC10T2 front suspension arms by blammojp
by Thingiverse
Last crawled date: 3 years, 3 months ago
Front control arms for a Team Associated RC10T2. May fit other RC10 variants (GT?). Design is simplified for printing as shown in the picture. Only one arm in file - mirror for the other side as needed.
I recommend stronger materials if possible. I printed my first set in PETG and they broke soon after a few rough tumbles (broke on the holes on the ends where they attach to the chassis). I printed my new set (in the photo) in polycarbonate - hoping these hold up better.
UPDATE 15 Dec 2020:
I tried many tweaks to the design and tried different materials (GizmoDorks PC, eSun Nylon, etc.) and different print orientations (sideways to improve layer alignment with respect to the holes), I continued to have issues where the arms kept breaking at the hinge points after 1-2 jumps off a skateboard ramp.
The latest v5 design seems to have finally fixed this when coupled with PolyMax PC filament - I thickened the arms about 2mm and increased the amount of material around the hinge pin holes. Still need to do more testing, but after multiple jumps and occasional bad landings they are still holding well, with some scrapes to the area around the hinge points even. The new photo is of the v5 design.
I recommend stronger materials if possible. I printed my first set in PETG and they broke soon after a few rough tumbles (broke on the holes on the ends where they attach to the chassis). I printed my new set (in the photo) in polycarbonate - hoping these hold up better.
UPDATE 15 Dec 2020:
I tried many tweaks to the design and tried different materials (GizmoDorks PC, eSun Nylon, etc.) and different print orientations (sideways to improve layer alignment with respect to the holes), I continued to have issues where the arms kept breaking at the hinge points after 1-2 jumps off a skateboard ramp.
The latest v5 design seems to have finally fixed this when coupled with PolyMax PC filament - I thickened the arms about 2mm and increased the amount of material around the hinge pin holes. Still need to do more testing, but after multiple jumps and occasional bad landings they are still holding well, with some scrapes to the area around the hinge points even. The new photo is of the v5 design.
Similar models
thingiverse
free
Team Associated RC10T2 Front Bulkhead by rcnand
... with the chassis. all directional improvements - but i will change this from a work in progress to complete once i have printed.
thingiverse
free
Redcat Racing Shredder Front Arm by billsmith221
...rm at 30 degree angle and with a 100% infill to get the strongest prints.
i will be posting the rear arms after i break them lol
thingiverse
free
Team Associated RC10T2 Front Caster Blocks (25 Degree) by rcnand
...2. this is the 25 degree version.
ream the hinge pin hole with a 1/8" drill bit and tap the ball stud mount with a 4-40 tap.
thingiverse
free
Pinion for Unomat Photo Stand by kukibiker
...for handle pin is... i make the reinforced file. the pin will be deep in the hole on both side, but this finaly should work well.
thingiverse
free
loo, toilet, wc hinge/bracket by simowilso
...by simowilso
thingiverse
one of the hinges holding the toilet seat broke so i printed a new one. it fits an ideal standard seat.
thingiverse
free
S911 / S912 Steering Arm by bricky50
... jumps and some crashes, it is still holding up very well. you might need to narrow the screw holes if the screws are too small.
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...body mount bracket for the rc10t2.
you may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.
thingiverse
free
Replacement Wheel by TheFisherOne
...t pictures if you manage to use this successfully.
i made some tweaks to the dimensions of the axle to better fit my vacuum in v5
thingiverse
free
Jumping Something by eskpetri
...o land on head and 1 point for trying to do that. more flips more points.
kenguruu was the the thing i was trying to do but ...
thingiverse
free
Pants Buckle by osarusan
.... i may also need to reinforce the area around the holes for sturdiness. but for now, we'll see how long this piece holds up.
Blammojp
thingiverse
free
Towel Rack/Hanger by blammojp
...ack for kitchen, bath, or wherever. designed for larger-format printers (such as my ender 5 plus); requires about 320mm bed size.
thingiverse
free
Flexible Cable Grommet by blammojp
..., for example). i used to cover holes for passing cables in my 3d printer enclosure.
can be scaled to different sizes if desired.
thingiverse
free
Ender 5 Plus MicroSwiss Cooling Duct - Single Side Only by blammojp
...etg duct started deforming when printing polycarbonate at near 300c...
should attach to the guilianom's fan shroud as before.
thingiverse
free
Vertical spool filament dryer by blammojp
...on (due to contact at the two edges) but may help if you run into a similar issue if it rolls too freely on the spool + bearings.
Rc10T2
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...unting bracket for the rc10t2.
this is not a very complex component, but print orientation will be critical to maintain strength.
thingiverse
free
Team Associated RC10T2 Front Body Post Mount by rcnand
...body mount bracket for the rc10t2.
you may need to ream out the screw holes slightly, but 4-40 screws should thread in just fine.
thingiverse
free
Team Associated RC10T2 Servo Mount/Spacer by rcnand
... an exact match for originals (2.4 vs 2.5 mm). these could easily be modified to match.
tap the mounting holes with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Rear Lower Shock Mount by rcnand
... larger to allow the screws to pass through more cleanly (if desired). the shock mounting holes should be tapped with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Front Caster Blocks (25 Degree) by rcnand
...2. this is the 25 degree version.
ream the hinge pin hole with a 1/8" drill bit and tap the ball stud mount with a 4-40 tap.
thingiverse
free
Team Associated RC10T2 Front Caster Blocks (30 Degree) by rcnand
...bit and tap the ball stud mount with a 4-40 tap.
if time allows, i may upload a 25 degree version (not that difficult to modify).
thingiverse
free
Team Associated RC10T2 Front Mini Bumper by rcnand
...ight filing after printing. similarly, you could probably modify this bumper to use more traditional non-100 degree countersinks.
thingiverse
free
Team Associated RC10T/RC10T2 12mm Hex Adapter by rcnand
...ssociated/team losi front bearing supported rims, the rear will be ~7 mm total (3.5 mm per side) wider when you use this adapter.
thingiverse
free
Team Associated RC10T2 Front Bulkhead by rcnand
... with the chassis. all directional improvements - but i will change this from a work in progress to complete once i have printed.
thingiverse
free
Team Associated RC10T2 Front Bulkhead by rcnand
...he areas near the hinge pin mounts may need to be filed slightly to clear the chassis (depending on tolerances for your printer).
Suspension
3ddd
free
Circolo Suspension
...circolo suspension
3ddd
circolo , suspension
this is the circolo led suspension
3d_export
$20
suspension
...pension
3dexport
suspension it is used in bicycle, motorcycle; and many more object<br>rendering is done in photo view 360
3ddd
$1
Fieltebek suspension
...fieltebek suspension
3ddd
fieltebek , suspension
fieltebek
3d_export
free
suspension
...suspension
3dexport
3ddd
$1
Botti Suspension
...botti suspension
3ddd
botti
люстра botti suspension
turbosquid
$25
suspension
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$8
suspension
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
SUSPENSION
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
DELIGHTFULL MATHENY | SUSPENSION
... matheny , suspension
delightfull matheny | suspension
design_connected
$16
Vaeder Suspension
...vaeder suspension
designconnected
modular lighting instruments vaeder suspension computer generated 3d model.
Arms
archibase_planet
free
Arm
...ase planet
arm hand right hand skeleton
arm human skeleton right arm n030515 - 3d model (*.gsm+*.3ds+*.max) for 3d visualization.
3ddd
$1
arm chair
...arm chair
3ddd
arm chair , пуф
arm chair
turbosquid
$5
arm
...arm
turbosquid
royalty free 3d model arm for download as obj on turbosquid: 3d models for games, architecture, videos. (1306158)
turbosquid
free
Arm
...arm
turbosquid
free 3d model arm for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1346955)
turbosquid
$29
Arm
...osquid
royalty free 3d model arm for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1382436)
3d_export
$5
coat of arms
...coat of arms
3dexport
coat of arms
3ddd
$1
ARM SOFA
...arm sofa
3ddd
arm sofa
3ddd
$1
Arm chair
...arm chair
3ddd
arm chair
3ddd
$1
Arm chair
...arm chair
3ddd
угловое
arm chair
3ddd
$1
ARM CHAIR
...arm chair
3ddd
arm chair clothes
Front
archibase_planet
free
Front
...front
archibase planet
facade front bluff
front 3d01a - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
front fork
...front fork
3dexport
front fork
3d_export
$5
Front Desk
...front desk
3dexport
modern and minimal reception front desk
3d_ocean
$4
Medical Front
...medical front
3docean
horror low medical
medical front
3d_ocean
$5
Front Desk
...front desk
3docean
desk front office reception
office reception counter or front desk. cad file and obj file included.
3ddd
free
Axor WaterDream by Front
...r , waterdream , front
axor waterdream by front
3d_export
$5
front nut eye
...front nut eye
3dexport
front nut eye
3d_export
$5
front screw eye
...front screw eye
3dexport
front screw eye
3d_export
$5
front clamping device
...front clamping device
3dexport
front clamping device
archive3d
free
Front 3D Model
...rchive3d
facade front bluff
front 3d01a - 3d model (*.gsm+*.3ds) for interior 3d visualization.