RC Airplane Stand Medium by jwerry

Last crawled date: 3 years, 1 month ago

Notice: This is a Very Large Print when Finished & Assembled 279 Meters or 85% of 1 Spool Approximately $21.25 @ $25.00 per 1KG Spool
This is a 3D printed replica of the stand available in wood athttp://www.foam-flite.com/shop/index.php?id_product=28&controller=product
The pieces may not be an exact replica because they were designed from scratch only using the images seen on the website listed above. The plan is to list all parts, quantities, settings, time and cost estimates based on $25 spools of filament. Early estimate is it will take less than one spool.
I will list all required hardware, the bolts only cost about $1 at Farm and Fleet.
I purchased 1/4" Carriage Bolts 3" long and cut them to length, (my preference)
Required Hardware
• 4 1/4” x 1 1/4” Carriage Bolts
• 4 1/4” x 1 1/2” Carriage Bolts
• 4 1/4” x 2 1/2” Carriage Bolts
• 12 1/4 - 20 Nuts
• 4 10-24 x 1½” Round Head Bolts
• 2 10-24 Nuts
• 2 10-24 Nylon Lock Nuts
CA Glue if you plan on using glue on the split base pieces.
I am going to add some Neoprene Foam to the edges of the arms that touch the plane.
16 Different Pieces, some will need to be printed multiple times.
Print Speed 2400 mm/min (my preference, not required)
Filament and time are for each piece, if you need multiple then multiply each by the count required.
Base - 6 Pieces
Base_Outside_P1_V2 (2) - 10327.8 mm - 3 hours 24 minutes
Base_Outside_P2_V2 (2) - 7106.9 mm - 2 hours 22 minutes
Base_Center_left_V2 (1) - 15301.9 mm - 5 hours 12 minutes
Base_Center_right_V2 (1) - 13897.8 mm - 4 hours 44 minutes
Base_Center_Bottom_left_V2 (1) - 8036.2 mm - 2 hours 49 minutes
Base_Center_Bottom_right_V2 (1) - 7225.9 mm - 2 hours 32 minutes
** Base Total - 79,331.2 mm - 26 hours 49 minutes (24% 1 Spool)
ARM (2) - 8 Pieces each Arm
Arm_A_v2 (2) - 9658.6 mm - 3 hours 17 minutes
Arm_B_v2 (1) - 8504.0 mm - 3 hours 0 minutes
Arm_B_P2 (2) - 2437.6 mm - 0 hours 51 minutes
Arm (2) - 6407.6 mm - 2 hours 12 minutes
Support_Arm (2) - 4497.5 mm - 1 hours 32 minutes
Washer_9mm (2) - 603.1. mm - 0 hours 14 minutes
Arm_Mount_v3 (1) - 13692.5 mm - 4 hours 27 minutes
Mount_Small_v3 (2) - 2836.7 mm - 0 hours 59 minutes
** Single Arm Total - 88571.2 mm - 25 hours 37 minutes (26.8% 1 Spool)
*** Both Arms Total - 177142.4 mm - 51 hours 14 minutes (53.6% 1 Spool)
Misc - 2 Pieces
Knob_large_v3 (12) - 20043.0 mm - 7 hours 45 minutes (all 12 at one time)
Knob_small_v3 (2) - 2135.5 mm - 0 hours 49 minutes (2 at one time)
** Misc Total - 22178.5 mm - 8 hours 34 minutes (6.7% 1 Spool)
*** Built Total - 278652.1 mm - 86 hours 37 minutes (84.4% 1 Spool @ $25 - $21.25)
All Pieces have been uploaded.
More instructions and pictures to come.
FYI: I am working on a CG Balance Addon for this stand, check out thing:3168828https://www.thingiverse.com/thing:3168828