Thingiverse
Rasptop 2.0 The Better Raspberry Pi 7" Laptop *Source Files Included* *UPDATED a lot* by morganlowe
by Thingiverse
Last crawled date: 3 years ago
Featured on Hackaday!
The Pi Project Family!
Super RetroPie Pod, The Raspberry Pi Desktop Arcade And of course Bananananana and The Green Demon
This is mostly based on my Rasptop from https://www.thingiverse.com/thing:2804933
Build it already!
It will cost about $150-350 USD to build based on choices of parts and computer inside.
It uses the same palmrest screws, keyboard, speakers, hinge screws, and USB panel mounts as the Rasptop above but with a better screen and more versatility.
A note on screen choices!
The Official Raspberry Pi Foundation Touchscreen has a resolution of 800x480 and is the easiest to wire but it's expensive to buy and that resolution is TERRIBLE for day to day use. You can force it to a better resolution on a Raspberry Pi by using the config.txt and setting the framebuffer size higher.
Set as follows:
framebuffer_width=1024
framebuffer_height=614
That helps a lot, but it's a hack.
There's many HDMI screens of better resolution out there and that's why I made the 2.0 here. I used a 1024x800 HDMI 7" 10 point touchscreen listed in the BOM. These are commonly USB powered and use USB for the touchscreen too. Both windows and linu supports it out of the box. Super easy!
Now, I have found that I needed to tweak the config.txt for these HDMI screen to boot properly too. Here's what I added:
hdmi_force_hotplug=1
disable_overscan=1
hdmi_group=2
hdmi_mode=87
You can put that at the bottom of your config.txt and this will set the HDMI mode to run these small screens.
There's also 800x600 versions of the same screen. While better than the RPi one it's still not much screen space and can it can be tough to fit things on the screen.
Just be aware of what you're buying! It's easy to go down a path that might lead to future frustration! I am super willing to help anyone build this though, PM me if you need a hand!
One more thing, If you get the voltage warning symbol you can disable it with this line in the config.txt
avoid_warnings=1
Also, I like to have the lights on my Pi setup so the red light is only on when the machine is off, like if you tell it to shutdown the red light comes on when it's safe to power down:
dtparam=pwr_led_trigger=none
dtparam=pwr_led_activelow=off
And finally I like the green light to pulse based on system load. This is called heartbeat:
dtparam=act_led_trigger=heartbeat
Off the shelf parts!
I made some big changes that well, made it thicker and larger but this allows it to be made with straight up off the shelf parts.
You will be soldering, wiring and setting up Linux!
Be aware of what you're getting into! Also I made the source files in SolidWorks 2017. Hit me up if you would like them sent to you in some other format, I will see what I can do.
BOM
Keyboard It helps to have the nicer one, fits better!
Micro USB Breakout
Amplifier
14 x M3.12 Plastite
2 x M4x45 Screws
2 x M4 Nylock Nuts
4 x M3x14 Screws
4 x M3 Nuts
Dual USB Panel Mount
Single USB Panel Mount
7" Capactive Touch Screen with 1024x600 Pixels or Pi Foundation Screen 800x480px
Flat Flex HDMI Cable Extension
You will need about 30cm of flat cable to run HDMI
HDMI Rasppberry Pi Screen Connector
Easy To Modify USB Hub
Some 24 x 15mm Speakers
20AWG Silicone Wire
USB Ends
3.5MM Stereo Audio Jacks
Slide Switch
A source of a battery
Soldering Iron, Flux, Solder
220mmx220mm capable 3D printer
Several Hours of Time
Asus Tinkerboard, Raspberry Pi 3 B+, Beaglebone, Banana Pi, Orange Pi, or other Single Board Computer.
Some cooling to fit your computer. I used active cooling on my latest builds. This fan works well.
Raspberry Pi 4B fits!
Notes on chargers:
With the 2 cell system, which is the best way to run this, you have some options for charging. If you plan to use this a lot especially while on charge I suggest a 5 amp charger board while a 2 amp is fine for most uses. I got mine most recently at Banggood. They offer the 2S 5 amp ones pretty cheap and they work good.
Either way you should add a heatsink to the charger board.
I got an assortment of small heatsinks and some thermal glue from amazon pretty cheap. On the 5 amp boards I used 2 heatsinks, one on top of the chip and one under it. For the 2 amp board I just used one heatsink on top of the chip. The thermal glue is not conductive so I used quite a bit on the top heatsinks to help them stay stable over the chip.
This is the 5 amp board without and with heatsinks.
If links are dead:
Let me know or search the item. The battery one keeps changing. You want a 10,000MAH booster pack with a LiPo battery. These are often sold as slim type about $10 USD.
Up Board option, Intel Atom and Full X64 System
Up Board This is a Intel processor x86[64bit] capable PC in a Raspberry Pi 3 form factor. I have uploaded a special base to support this board. You should also purchase the Active Cooling the USB 3 OTG cable and the USB 2 Dual Port Cable since it does not include onboard WIFi or Bluetooth I am using a Mini USB WiFI/BT
The base for the Up board is 33mm deep. The extra depth is for the cooling. There's a lot going on for this little board but hey, it plays Crysis!!
Power Options!
7.4v 2S LiPo high output and long runtime:
Use this one please. It provides the best results and the longest battery life. Used with a 9 volt charger it charges up quickly and safely with little excess heat.
2S charger 9-15v input
2S Balance and Protection Board
DC to DC Buck Converter 5amps
2S Charger Indicator
Small MOSFET Module
I used a 5.5mmx2.1mm DC Barrel jack mounted just above the USB input with a hole drilled there. I picked these because they are really small and I just super glued it in.
9 volt 5amp Power Supply, using 9v instead of 12v greatly reduces heat in the charger circuit
Matched pair of cells.
How I wired it:
Starting with the batteries I wired them each with a length of 20ga silicone wire then on the balance board you connect positive from one cell and negative from the other to the B+ and B+ tabs on the balance board. The leftover positve and negative wire both go to the BM pad together making a series connection.
The P+ and P- from the balance board then go to the MOSFET input side. This is also where the positive and negative from the charger board attach so it can charge with the switch off. I used 24GA wire from the charger to the cells. I also used 24gs from the DC barrel jack to the charger board.
You need a wire from Battery + to go to the switch as well, this can be 24ga or even smaller. and the wire coming back from the switch goes to the input signal on the MOSFET module.
On the output of the MOSFET module connect the battery level indicator and the DC to DC converter board so they come on when the switch is on.
Be sure to set the voltage before connecting anything to the DC to DC converter!
No more than 5.2 volts. Set to 5.1 volts!
I put the Micro USB in still and just wired it directly to the 5v side of the system so I can plug power in there and not use the battery to run it on the bench or something.
So in a test with Ubuntu 18.04 MATE and Chromium browser running Google Play Music I got 14.5 hours of battery life on a full charge playing over bluetooth speakers and doing other random things on this battery arrangement.
14.5 hours!?
Yeah, a lot of battery.
Adafruit Powerboost:
This is the worst option but easier to wire. It provides a MAX of 2 amps! So be aware a Pi 3b+ is pushing it. This is not recommended.
Adafruit powerboost 1000c
Single large cell
Only RPI3 form factor fits as is!
I am using the Asus Tinkerboard inside mine:https://www.asus.com/us/Single-Board-Computer/Tinker-Board/
Powerful board that fits where an RPi3 fits!
Inside this the screen bezel is changed to hold the new LCD unit and the Pi has been moved to the left to make room for HDMI wiring. Due to space constraints I am removing the HDMI port from the screen to replace it with a 20 pin .5mm pitch FFC connector. This will connect to the cable listed above to carry the HDMI signal to the screen.
The screen is powered by a micro USB port, this is also how the touchscreen connects to the PC. To make this work I used the Hackable USB hub listed in BOM to carry the USB signal for the screen as well as connect to the keyboard USB port. This leaves 2 internal ports left if I wish.
The audio plugs into the headphone jack, the HDMI plugs into the HDMI port. The batteries sit to the right inside the case, electronics to the left.
The little spacers are for holding the screen PCB in. Need 4 of them and they go between the screen PCB and Bezel Rear Cover so the screws hold it all tight. The screws are for m3x14mm.
For the keyboard I hooked it to the 5v lines and used a 3.3v 500mah regulator attached to the battery input. This is enough that it wont show a low battery light on the keyboard.
What also works to power the keyboard is hooking the battery lines of the keyboard to the GND and 3.3V pins on the computer. It draws less than 50ma so this is perfectly acceptable.
The unit size is still 200x150mm approx! Should fit on any 220x220 printer like the Anet A8 I have.
I recommend PLA for this one! With the hinge and way it's setup PLA has the best properties. See Print Settings for details.
Again once done there will be lots of pictures and more detailed instructions. For now Like, Comment and Share!
If you have an idea or feature let me know.
UPDATE 4/13/2018 Updated files for Adafruit Powerboost 1000 use. All parts have been ordered. Screens are coming from China but I hope to have them in 2 weeks.
Update 4/14/18 First part is printed! The base: https://youtu.be/FfbuAbDIj-k
Update 4/15/18 Printed the base and made some adjustments to fit things in better. Debating making the whole thing a little deeper to fit more ports but... I think not, I dunno.
Update 4/16/18 Updated the base to make it even easier to print and stronger with still better air flow. Removed side vents and added 3rd row to front vents. Cleaned up the files and re-rendered in colors.
Update 4/27/2018 Got all the parts! Now the design should be close to final. Printing it now!
Update 5/5/18 Been so busy! Anyways I completely rebuilt my printer again after wearing it out. New Bl Touch sensor and glass build surface. Redesigned the screen bezel on this a bit to fit better, but it's a little more of a pain to print now. Also had to rebuild the rear bezel cover for more space. Changed all the slots to hex holes because I like that look. Overall this should look and be quite rugged. All files are re-uploaded.
Update 5/16/18 Been slow going but I finally printed the screen portion and did test fits. It's a little tight side to side so opened that up and now it sits in there much nicer. Due to the way these screens are built the top wound up 2mm thicker.
Update 8/8/18 OK, it's been a minute. I have been testing, printing and working on the power system. I think it's time to step it up to a 2s 8.4 system. This will provide more amps and faster charging, though sacrifices the ability to charge from USB. Still, I think it will be worth it.
I ordered some parts from China on Ebay:
Voltage reg: https://www.ebay.com/itm/5A-Mini-DC-DC-Buck-Step-Down-Converter-Voltage-Regulator-3-3V-5V-6V-9V-12V-24V/263198737343?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
2 amp charger circuit: https://www.ebay.com/itm/Charging-Charger-Module-1S-3-7V-2S-7-4V-Lithium-Li-ion-18650-Battery-Cell-8-4V/192266131232?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
USB 2s charger to see how it works: https://www.ebay.com/itm/USB-2S-7-4V-8-4V-Lithium-Lipo-Li-ion-18650-Battery-Charging-Board-Charger-Module/272750949115?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
And battery protection board: https://www.ebay.com/itm/2S-8A-Li-ion-Lithium-LiPo-Battery-18650-Charger-Protection-Board-Cell-7-4V-8-4V/323268969256?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
I do plan on using 10k MAH LI-POs. I don't want it to blow up....
It didn't blow up!
I finally put it together, check the makes to see it!
1/25/19 All files updated! Redesigned the HDMI screen bezel to use a FPV HDMI extension and one of the Raspberry Pi HDMI backpack connectors. This will double the cable back into the space made in the cover.
It's thick!
By design the whole thing is pretty thick. Not much I can do about this really. Using off the shelf parts means compromises must be made but now besides some weird cobbled together connectors nothing needs to be modded. For the USB I got solder on micro ends and just am using one without the case to fit.
1/26/19 Re created all files and renders. Tweaked the fit and finish for greater ease of use with various design options. Soilidworks 2017 source file included. Unit will need to be printed with support on the base, bezel and back cover. Only the palmrest can be printed with out support and I recommend a .2mm nozzle for that but I did print it with a .4 and a .3mm ok.
2/5/19 Added a pin and socket in the center of the palmrest to help hold it down and support it when typing.
2/22/19 Added the screen bezel and option to use a Raspberry Pi Foundation 7" Touchscreen at 800x480
2/24/19 Added a version of the base with a 8.2mm cutout to fit the DC barrel jack for the 12v charging input on the 7.2v 2S system. This moved the Micro USB down 2 mm. I also added the custom base for the Up Board. This has no SD slot and no micro USB power input. It adds more cooling openings and a USB 3 socket. Mount the USB 3 OTG cable with 3M VHB tabe. This is only for the 2s 7.2v power system.
3/8/19 Up board version built and final files uploaded. For the USB 3.0 port I am using 3M VHB tape that is 2mm thick and the port spacing matches that.
3/22/19 Added a version of the palmrest that uses the listed LiPO battery meter and has a cutout in it to fit.
7/11/19 Added a base modded to hold a RPI 4B with two USB 3 panel mounts in the side. This comes with 7.2v provisions.
12/2/19 Updated the RPI 4B edition adding 2mm to the height and increasing vents to help cool it!
1/16/2020 A year later! (Almost, March 9th, 2019 is the build date) Here's a few pics of the Up! board one. This being a full on Windows 10 X64 machine gets the most use. I have broken the HDMI cable, I dropped it and snapped the hinge off the bezel so it has a copper color one now and the keyboard just got a bit weird so printing a new black palmrest without holes melted in it that are no longer used. The batteries and charging system have worked flawlessly. So has the Up! board. So much power in such a small space!
Still a mess inside!
The Little Green Demon
Up! Boot
Window 10 ready!
New palm rest installed.
Glamor shot on the big CNC knee mill.
Backside with the 4G LTE backpack installed. This attaches with magnets to the laptop and provides cellular internet. This also attaches to my Panasonic Toughbook CF-19 MK7
And Rasptop 2.0 in the wild again. the 7 inch 1024x800 screen is great for on the go media.
Come hang out get help and talk printers and more on our Discord!
Update 7/29/2020 Added a new bezel and back cover for LCDs with the HDMI port right up near the top and 2 micro USB ports. These seem to be common on Amazon right now. Use the High Wire parts for these.
The Pi Project Family!
Super RetroPie Pod, The Raspberry Pi Desktop Arcade And of course Bananananana and The Green Demon
This is mostly based on my Rasptop from https://www.thingiverse.com/thing:2804933
Build it already!
It will cost about $150-350 USD to build based on choices of parts and computer inside.
It uses the same palmrest screws, keyboard, speakers, hinge screws, and USB panel mounts as the Rasptop above but with a better screen and more versatility.
A note on screen choices!
The Official Raspberry Pi Foundation Touchscreen has a resolution of 800x480 and is the easiest to wire but it's expensive to buy and that resolution is TERRIBLE for day to day use. You can force it to a better resolution on a Raspberry Pi by using the config.txt and setting the framebuffer size higher.
Set as follows:
framebuffer_width=1024
framebuffer_height=614
That helps a lot, but it's a hack.
There's many HDMI screens of better resolution out there and that's why I made the 2.0 here. I used a 1024x800 HDMI 7" 10 point touchscreen listed in the BOM. These are commonly USB powered and use USB for the touchscreen too. Both windows and linu supports it out of the box. Super easy!
Now, I have found that I needed to tweak the config.txt for these HDMI screen to boot properly too. Here's what I added:
hdmi_force_hotplug=1
disable_overscan=1
hdmi_group=2
hdmi_mode=87
You can put that at the bottom of your config.txt and this will set the HDMI mode to run these small screens.
There's also 800x600 versions of the same screen. While better than the RPi one it's still not much screen space and can it can be tough to fit things on the screen.
Just be aware of what you're buying! It's easy to go down a path that might lead to future frustration! I am super willing to help anyone build this though, PM me if you need a hand!
One more thing, If you get the voltage warning symbol you can disable it with this line in the config.txt
avoid_warnings=1
Also, I like to have the lights on my Pi setup so the red light is only on when the machine is off, like if you tell it to shutdown the red light comes on when it's safe to power down:
dtparam=pwr_led_trigger=none
dtparam=pwr_led_activelow=off
And finally I like the green light to pulse based on system load. This is called heartbeat:
dtparam=act_led_trigger=heartbeat
Off the shelf parts!
I made some big changes that well, made it thicker and larger but this allows it to be made with straight up off the shelf parts.
You will be soldering, wiring and setting up Linux!
Be aware of what you're getting into! Also I made the source files in SolidWorks 2017. Hit me up if you would like them sent to you in some other format, I will see what I can do.
BOM
Keyboard It helps to have the nicer one, fits better!
Micro USB Breakout
Amplifier
14 x M3.12 Plastite
2 x M4x45 Screws
2 x M4 Nylock Nuts
4 x M3x14 Screws
4 x M3 Nuts
Dual USB Panel Mount
Single USB Panel Mount
7" Capactive Touch Screen with 1024x600 Pixels or Pi Foundation Screen 800x480px
Flat Flex HDMI Cable Extension
You will need about 30cm of flat cable to run HDMI
HDMI Rasppberry Pi Screen Connector
Easy To Modify USB Hub
Some 24 x 15mm Speakers
20AWG Silicone Wire
USB Ends
3.5MM Stereo Audio Jacks
Slide Switch
A source of a battery
Soldering Iron, Flux, Solder
220mmx220mm capable 3D printer
Several Hours of Time
Asus Tinkerboard, Raspberry Pi 3 B+, Beaglebone, Banana Pi, Orange Pi, or other Single Board Computer.
Some cooling to fit your computer. I used active cooling on my latest builds. This fan works well.
Raspberry Pi 4B fits!
Notes on chargers:
With the 2 cell system, which is the best way to run this, you have some options for charging. If you plan to use this a lot especially while on charge I suggest a 5 amp charger board while a 2 amp is fine for most uses. I got mine most recently at Banggood. They offer the 2S 5 amp ones pretty cheap and they work good.
Either way you should add a heatsink to the charger board.
I got an assortment of small heatsinks and some thermal glue from amazon pretty cheap. On the 5 amp boards I used 2 heatsinks, one on top of the chip and one under it. For the 2 amp board I just used one heatsink on top of the chip. The thermal glue is not conductive so I used quite a bit on the top heatsinks to help them stay stable over the chip.
This is the 5 amp board without and with heatsinks.
If links are dead:
Let me know or search the item. The battery one keeps changing. You want a 10,000MAH booster pack with a LiPo battery. These are often sold as slim type about $10 USD.
Up Board option, Intel Atom and Full X64 System
Up Board This is a Intel processor x86[64bit] capable PC in a Raspberry Pi 3 form factor. I have uploaded a special base to support this board. You should also purchase the Active Cooling the USB 3 OTG cable and the USB 2 Dual Port Cable since it does not include onboard WIFi or Bluetooth I am using a Mini USB WiFI/BT
The base for the Up board is 33mm deep. The extra depth is for the cooling. There's a lot going on for this little board but hey, it plays Crysis!!
Power Options!
7.4v 2S LiPo high output and long runtime:
Use this one please. It provides the best results and the longest battery life. Used with a 9 volt charger it charges up quickly and safely with little excess heat.
2S charger 9-15v input
2S Balance and Protection Board
DC to DC Buck Converter 5amps
2S Charger Indicator
Small MOSFET Module
I used a 5.5mmx2.1mm DC Barrel jack mounted just above the USB input with a hole drilled there. I picked these because they are really small and I just super glued it in.
9 volt 5amp Power Supply, using 9v instead of 12v greatly reduces heat in the charger circuit
Matched pair of cells.
How I wired it:
Starting with the batteries I wired them each with a length of 20ga silicone wire then on the balance board you connect positive from one cell and negative from the other to the B+ and B+ tabs on the balance board. The leftover positve and negative wire both go to the BM pad together making a series connection.
The P+ and P- from the balance board then go to the MOSFET input side. This is also where the positive and negative from the charger board attach so it can charge with the switch off. I used 24GA wire from the charger to the cells. I also used 24gs from the DC barrel jack to the charger board.
You need a wire from Battery + to go to the switch as well, this can be 24ga or even smaller. and the wire coming back from the switch goes to the input signal on the MOSFET module.
On the output of the MOSFET module connect the battery level indicator and the DC to DC converter board so they come on when the switch is on.
Be sure to set the voltage before connecting anything to the DC to DC converter!
No more than 5.2 volts. Set to 5.1 volts!
I put the Micro USB in still and just wired it directly to the 5v side of the system so I can plug power in there and not use the battery to run it on the bench or something.
So in a test with Ubuntu 18.04 MATE and Chromium browser running Google Play Music I got 14.5 hours of battery life on a full charge playing over bluetooth speakers and doing other random things on this battery arrangement.
14.5 hours!?
Yeah, a lot of battery.
Adafruit Powerboost:
This is the worst option but easier to wire. It provides a MAX of 2 amps! So be aware a Pi 3b+ is pushing it. This is not recommended.
Adafruit powerboost 1000c
Single large cell
Only RPI3 form factor fits as is!
I am using the Asus Tinkerboard inside mine:https://www.asus.com/us/Single-Board-Computer/Tinker-Board/
Powerful board that fits where an RPi3 fits!
Inside this the screen bezel is changed to hold the new LCD unit and the Pi has been moved to the left to make room for HDMI wiring. Due to space constraints I am removing the HDMI port from the screen to replace it with a 20 pin .5mm pitch FFC connector. This will connect to the cable listed above to carry the HDMI signal to the screen.
The screen is powered by a micro USB port, this is also how the touchscreen connects to the PC. To make this work I used the Hackable USB hub listed in BOM to carry the USB signal for the screen as well as connect to the keyboard USB port. This leaves 2 internal ports left if I wish.
The audio plugs into the headphone jack, the HDMI plugs into the HDMI port. The batteries sit to the right inside the case, electronics to the left.
The little spacers are for holding the screen PCB in. Need 4 of them and they go between the screen PCB and Bezel Rear Cover so the screws hold it all tight. The screws are for m3x14mm.
For the keyboard I hooked it to the 5v lines and used a 3.3v 500mah regulator attached to the battery input. This is enough that it wont show a low battery light on the keyboard.
What also works to power the keyboard is hooking the battery lines of the keyboard to the GND and 3.3V pins on the computer. It draws less than 50ma so this is perfectly acceptable.
The unit size is still 200x150mm approx! Should fit on any 220x220 printer like the Anet A8 I have.
I recommend PLA for this one! With the hinge and way it's setup PLA has the best properties. See Print Settings for details.
Again once done there will be lots of pictures and more detailed instructions. For now Like, Comment and Share!
If you have an idea or feature let me know.
UPDATE 4/13/2018 Updated files for Adafruit Powerboost 1000 use. All parts have been ordered. Screens are coming from China but I hope to have them in 2 weeks.
Update 4/14/18 First part is printed! The base: https://youtu.be/FfbuAbDIj-k
Update 4/15/18 Printed the base and made some adjustments to fit things in better. Debating making the whole thing a little deeper to fit more ports but... I think not, I dunno.
Update 4/16/18 Updated the base to make it even easier to print and stronger with still better air flow. Removed side vents and added 3rd row to front vents. Cleaned up the files and re-rendered in colors.
Update 4/27/2018 Got all the parts! Now the design should be close to final. Printing it now!
Update 5/5/18 Been so busy! Anyways I completely rebuilt my printer again after wearing it out. New Bl Touch sensor and glass build surface. Redesigned the screen bezel on this a bit to fit better, but it's a little more of a pain to print now. Also had to rebuild the rear bezel cover for more space. Changed all the slots to hex holes because I like that look. Overall this should look and be quite rugged. All files are re-uploaded.
Update 5/16/18 Been slow going but I finally printed the screen portion and did test fits. It's a little tight side to side so opened that up and now it sits in there much nicer. Due to the way these screens are built the top wound up 2mm thicker.
Update 8/8/18 OK, it's been a minute. I have been testing, printing and working on the power system. I think it's time to step it up to a 2s 8.4 system. This will provide more amps and faster charging, though sacrifices the ability to charge from USB. Still, I think it will be worth it.
I ordered some parts from China on Ebay:
Voltage reg: https://www.ebay.com/itm/5A-Mini-DC-DC-Buck-Step-Down-Converter-Voltage-Regulator-3-3V-5V-6V-9V-12V-24V/263198737343?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
2 amp charger circuit: https://www.ebay.com/itm/Charging-Charger-Module-1S-3-7V-2S-7-4V-Lithium-Li-ion-18650-Battery-Cell-8-4V/192266131232?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
USB 2s charger to see how it works: https://www.ebay.com/itm/USB-2S-7-4V-8-4V-Lithium-Lipo-Li-ion-18650-Battery-Charging-Board-Charger-Module/272750949115?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
And battery protection board: https://www.ebay.com/itm/2S-8A-Li-ion-Lithium-LiPo-Battery-18650-Charger-Protection-Board-Cell-7-4V-8-4V/323268969256?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649
I do plan on using 10k MAH LI-POs. I don't want it to blow up....
It didn't blow up!
I finally put it together, check the makes to see it!
1/25/19 All files updated! Redesigned the HDMI screen bezel to use a FPV HDMI extension and one of the Raspberry Pi HDMI backpack connectors. This will double the cable back into the space made in the cover.
It's thick!
By design the whole thing is pretty thick. Not much I can do about this really. Using off the shelf parts means compromises must be made but now besides some weird cobbled together connectors nothing needs to be modded. For the USB I got solder on micro ends and just am using one without the case to fit.
1/26/19 Re created all files and renders. Tweaked the fit and finish for greater ease of use with various design options. Soilidworks 2017 source file included. Unit will need to be printed with support on the base, bezel and back cover. Only the palmrest can be printed with out support and I recommend a .2mm nozzle for that but I did print it with a .4 and a .3mm ok.
2/5/19 Added a pin and socket in the center of the palmrest to help hold it down and support it when typing.
2/22/19 Added the screen bezel and option to use a Raspberry Pi Foundation 7" Touchscreen at 800x480
2/24/19 Added a version of the base with a 8.2mm cutout to fit the DC barrel jack for the 12v charging input on the 7.2v 2S system. This moved the Micro USB down 2 mm. I also added the custom base for the Up Board. This has no SD slot and no micro USB power input. It adds more cooling openings and a USB 3 socket. Mount the USB 3 OTG cable with 3M VHB tabe. This is only for the 2s 7.2v power system.
3/8/19 Up board version built and final files uploaded. For the USB 3.0 port I am using 3M VHB tape that is 2mm thick and the port spacing matches that.
3/22/19 Added a version of the palmrest that uses the listed LiPO battery meter and has a cutout in it to fit.
7/11/19 Added a base modded to hold a RPI 4B with two USB 3 panel mounts in the side. This comes with 7.2v provisions.
12/2/19 Updated the RPI 4B edition adding 2mm to the height and increasing vents to help cool it!
1/16/2020 A year later! (Almost, March 9th, 2019 is the build date) Here's a few pics of the Up! board one. This being a full on Windows 10 X64 machine gets the most use. I have broken the HDMI cable, I dropped it and snapped the hinge off the bezel so it has a copper color one now and the keyboard just got a bit weird so printing a new black palmrest without holes melted in it that are no longer used. The batteries and charging system have worked flawlessly. So has the Up! board. So much power in such a small space!
Still a mess inside!
The Little Green Demon
Up! Boot
Window 10 ready!
New palm rest installed.
Glamor shot on the big CNC knee mill.
Backside with the 4G LTE backpack installed. This attaches with magnets to the laptop and provides cellular internet. This also attaches to my Panasonic Toughbook CF-19 MK7
And Rasptop 2.0 in the wild again. the 7 inch 1024x800 screen is great for on the go media.
Come hang out get help and talk printers and more on our Discord!
Update 7/29/2020 Added a new bezel and back cover for LCDs with the HDMI port right up near the top and 2 micro USB ports. These seem to be common on Amazon right now. Use the High Wire parts for these.
Similar models
thingiverse
free
Baofeng UV 5R usb charger by Flori444
...ging-board-charger-module/272969439691?hash=item3f8e3f19cb:g:gdsaaoswfv9xzcyq)
revision 1: fits, contact mounting can be improved
thingiverse
free
7" Touchscreen with Keyboard Rugged Raspberry Pi Tablet by morganlowe
...s as i have not yet assembled mine!
i made keyboard clips, these glue in with superglue to hold the keyboard in place.
thank you!
thingiverse
free
Baofeng UV-B6 UV-B5 battery by ThunderVG
.../item/2pcs-boosting-converter-power-supply-module-step-up-converter-dc-dc-voltage-regulator-adjustable-pcb-board/32821976125.html
thingiverse
free
DJI FPV Video Out Monitor by shnlls_fpv
...ition for the on/off switch and the usb otg output in the backplate.
if you have any suggestions or questions please let me know!
thingiverse
free
e cig battery charger by clayton13
...i took the 2 battery holders from 2 old chargers. and used the usb wire from 1 of the cargers to supply power to the 4056 boards,
thingiverse
free
Hinged Raspberry Pi Case with LiIon Battery pack and power/charge circuit by wandrson
... may 2017
i have updated the design and included the autodesk fusion 360 design files for anyone who wishes to modify the design.
thingiverse
free
Raspberry PI Sleeve mount (No power, HDMI, headphone ports) by masterolly
...hard-wire power connection to the back of the board via tp1(+) and tp2(-) (which doesn't bypass the board's safety fuse).
thingiverse
free
"Wireless Bladeless Fan" - Powered by USB-C + 2x18650 Batteries by b_cfm
...s battery holder
2s battery indicator
usb-c connector
on/off switch
turn it over and it becomes a great fume extractor :)
enjoy !
thingiverse
free
hdmipi stand by mread
... port.
.
kickstarter project :
.https://www.kickstarter.com/projects/697708033/hdmipi-affordable-9-high-def-screen-for-the-raspbe
3dwarehouse
free
USB 2.4A Charger Board
...usb 2.4a charger board
3dwarehouse
usb 2.4a mobile power bank charging module lithium battery charger board
Rasptop
thingiverse
free
RaspTop 2.0 by ericd_86
...https://youtu.be/s7_b0lqukum
rasptop version 1.0: https://www.thingiverse.com/thing:2350648
youtube: https://youtu.be/cd0m5y3s07s
thingiverse
free
RaspTop by ericd_86
...link. the hdmi i used was a little tight, i have a 90-degree angle one but i couldn't find it. all in all, works pretty well.
thingiverse
free
Rasptop! Raspberry Pi Laptop with Official Pi Foundation 7" Touchscreen *Just 5 Parts!* *Source files included* by morganlowe
...s. also added a peg for the palmrest to rest on for support while typing.
2/10/19 adjusted some base dimensions for better fit.
thingiverse
free
7" Touchscreen with Keyboard Rugged Raspberry Pi Tablet by morganlowe
...by morganlowe thingiverse this is a mod of my rasptop 2.0 laptop to create a pretty rugged mildly water...
grabcad
free
Rasptop 2.0 Raspberry Pi 7" Laptop with Many Options!
... a few parts, uses off the shelf parts and is easy to print and build!
see included pdf for detailed instructions.
thank you!
Morganlowe
thingiverse
free
AM8 - 3DLS Gantry Position Tool by morganlowe
...am8 - 3dls gantry position tool by morganlowe
thingiverse
just a simple thing to set where the gantry should go!
thingiverse
free
Edge Clamp Spool Holder by morganlowe
...ng. a spool holder to clamp on the edge of a desk or table. all 3d printed. fits all the spools i have ever encountered.
thanks!
thingiverse
free
Filler Jig for KING Joints by morganlowe
... joints for the larger king pre-rolls.
print upright with support everywhere on the funnel side, no support needed on the poker.
thingiverse
free
Bolt Shaped Drip Tip! by morganlowe
...eaded bolt with m12x1.25 threads for your e-cig!
see it printed here: https://youtu.be/poxalukhzve
enjoy, don't get screwed!
thingiverse
free
Drawing stand for Surface Pro by morganlowe
...ng. made it for my artist friend and he's loving it. uses 14 6mmx2mm round rubber feet. 10 on top 4 on the bottom.
thank you
thingiverse
free
Panasonic Toughbook CF-U1 HDD Cover by morganlowe
...s is a cover without a caddy for the cf-u1 ssd mod
just made and tested it with my mk2 cf-u1. fits and seals properly.
thank you!
thingiverse
free
Bowden Tube Bone by morganlowe
...ides snug over the tubes and just keeps them from going nuts. i might be the only person ever to need this but here it is!
enjoy!
thingiverse
free
Trowel for 50mm Concrete Curb by morganlowe
...ts in 2 parts with 3.8mm plastite screws. kinda niche but who knows, maybe you can use it! source files included, solidworks 2017
thingiverse
free
Spark Plug Inspired Drip Tip by morganlowe
...y universal. the outside hex is 19mm and it's 20mm tall without the tank nipple. it uses a 1x7mm o ring. print with support!
thingiverse
free
Spark Plug Inspired Drip Tip Tall Version by morganlowe
...:3013945
i found these print really well upside down with no support and a nice brim to stick it down. they are very thin walled.
Laptop
3d_export
$5
Laptop
...laptop
3dexport
laptop
archibase_planet
free
Laptop
...laptop
archibase planet
notebook laptop pc
laptop - 3d model for interior 3d visualization.
archibase_planet
free
Laptop
...laptop
archibase planet
notebook laptop pc
laptop asus - 3d model for interior 3d visualization.
3d_export
$5
Laptop
...laptop
3dexport
laptop with good typeboard. will be happy if it will be usefull for someone
3d_ocean
$19
laptop
...d com computer dell electronic high poly inspiron lap lapi laptop material model new tab usb
high poly uv unwrap, textured laptop
3d_export
$6
Laptop
...it your taste. the model consists lot of meshs. laptop body laptop cap buttons speaker cabinet speakers table table legs sul etc
3d_ocean
$8
Office Laptop
...rings.obj blender_rings.obj //////////////////////////////////////////////////////////////////////////////////////////////////...
turbosquid
$7
Laptop
...top
turbosquid
royalty free 3d model laptop for download as on turbosquid: 3d models for games, architecture, videos. (1488076)
turbosquid
$2
laptop
...laptop
turbosquid
free 3d model laptop for download as max on turbosquid: 3d models for games, architecture, videos. (1618080)
turbosquid
$10
Laptop
...
turbosquid
royalty free 3d model laptop for download as skp on turbosquid: 3d models for games, architecture, videos. (1375855)
Raspberry
3d_export
free
raspberry
...raspberry
3dexport
3d model of a raspberry. i tried to make it realistic.
turbosquid
$27
Raspberries
...y free 3d model raspberries for download as max, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1354176)
turbosquid
$14
Raspberries
...y free 3d model raspberries for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1364663)
3d_export
$5
raspberry pi
...raspberry pi
3dexport
carcasa para la raspberry pi
turbosquid
$99
Raspberry
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
raspberries
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Raspberries 3D Model
...raspberries 3d model archive3d raspberries raspberry raspberries n300911 - 3d model (*.3ds) for interior 3d...
3d_export
$5
raspberry fruit
...raspberry fruit
3dexport
3d_export
$5
raspberry
...y different sizes. their color ranges from light burgundy to pink. there are formats: obj, 3ds, blend, dae, fbx, mtl.<br>:)
evermotion
$12
raspberries 23 am130
...evermotion raspberries 23 am130 evermotion key 23 food fruit raspberry fruits am130 raspberries highly detailed 3d model of raspberries...
Pi
design_connected
$11
Pi
...pi
designconnected
ligne roset pi chairs computer generated 3d model. designed by thibault desombre.
3d_export
$5
raspberry pi
...raspberry pi
3dexport
carcasa para la raspberry pi
turbosquid
$18
pied
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Emme pi light
...emme pi light
3ddd
emme pi light
люста emme pi light
3ddd
$1
Emme pi light
...emme pi light
3ddd
emme pi light
бра классическое emme pi light
3ddd
$1
Emme Pi Light
...emme pi light
3ddd
emme pi light
3ddd
$1
Emme Pi Light
...emme pi light
3ddd
emme pi light
design_connected
$16
Pi-Air
...pi-air
designconnected
living divani pi-air lounge chairs computer generated 3d model. designed by harry & camila.
3d_ocean
$15
Manneken Pis
...picting a naked little boy urinating into a fountain’s basin. (wikipedia) the model was sculpted in blender 2.70a rendered wit...
3ddd
$1
Emme pi light
...emme pi light
3ddd
emme pi light
люстра классическая фирма: emme pi light
артикул: 3595/5/cot/12/wh
0
turbosquid
$12
Calligraphic Digit 0 Number 0
...hic digit 0 number 0 for download as max, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1389318)
3d_export
$6
set-0
...set-0
3dexport
turbosquid
$6
hedge 0
...yalty free 3d model hedge 0 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1450353)
turbosquid
$5
Nuber 0
...oyalty free 3d model nuber 0 for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1564674)
turbosquid
$22
0.jpg
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Steam Locomotive Fowler 4F 0-6-0
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Liquid Number 0
... model liquid number 0 for download as c4d, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1689919)
turbosquid
$45
Dragon360_perspShape_tmp.0.jpg
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$8
Rocks Debris 0
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$18
wood-guardrail-fence 0
...wood-guardrail-fence 0
3dexport
wood-guardrail-fence 0<br>3ds max 2015
Better
3ddd
$1
Мозаика Better B-MOS D1
...os d1
3ddd
better , мозаика
мозаика better b-mos d1.
розтайленая мною.
+ бамп
+ рефлеккт
turbosquid
$19
BETTER THAN CHOCOLATE SOFA
... better than chocolate sofa for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1144132)
3d_export
$5
Soviet Tank T-150
...t-150 3dexport simple tank model. in project texture are better ...
archive3d
free
Polycarbonate 3D Model
...polycarbonate plastic polycarbonate sheet a little bit oversized for better ...
3d_export
$20
Terminator
...a robot created by skynet to defeat the resistance. better watch the movie if you haven’t seen it...
3d_export
free
simple grass
...simple grass scene with procedural texture for grass, is better swaps the texture of grass by...
3d_export
$5
picture-mirror
...father,for the bath,it is desirable to make out of wood,better than...
3ddd
$1
APLLES with wood vase
...3ddd яблоко zip archive contain fbx model too, for better textures import to 3d software. kind...
3d_export
$5
vinyl record player
...size 295x260mm without any materials (just standart grey for better ...
3ddd
$1
Armchair 400
...armchair 400, designed by alvar aalto in 1936 and better known as tank. pelt coat idea by...
Updated
turbosquid
$5
orthographic room (updated)
...ee 3d model orthographic room (updated) for download as blend on turbosquid: 3d models for games, architecture, videos. (1375451)
turbosquid
$95
Romantic Bedroom - Updated
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$39
Sofa. Updated release
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Procedurally updating cartoon crystal
...l procedurally updating cartoon crystal for download as blend on turbosquid: 3d models for games, architecture, videos. (1525853)
3d_export
$5
10 Surfboard s UPDATE
...10 surfboard s update
3dexport
3d_export
$10
chair updated rocking
...chair updated rocking
3dexport
armchair renewed plywood 18 mm. for cnc machines. layout in the stp archive.
turbosquid
free
Marble Table Updated
...el marble table for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1201300)
turbosquid
$35
Mauser 1930the model is updated with the kits
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$145
Contemporary Bedroom Collection Vol 1 - Updated
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$16
B&B Mart Armchair MPRN (Updated)
...art armchair mprn (updated) for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1284355)
Source
turbosquid
$30
source
...e
turbosquid
royalty free 3d model source for download as ma on turbosquid: 3d models for games, architecture, videos. (1154551)
3d_export
$7
Source
...er software such as blender, 3d max, unity in the preview you will see the model with its respective materials, textures and mesh
design_connected
$13
Master Line Source
...master line source
designconnected
piega master line source computer generated 3d model.
3ddd
$1
SodaStream Source
...sodastream source
3ddd
сифон
designed by yves béhar
сифон компании sourcestream, изготовленный в современном стиле
turbosquid
$199
Demon source files
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$99
Water Source Animation
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
THEATRICAL LIGHT - SOURCE 4
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Cross 3D print source model
... 3d print source model for download as max, max, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1680597)
turbosquid
$22
Column capital source 3dsMax 001
...smax 001 3d model for download as max, max, max, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1683199)
3ddd
free
Lite Source LS-21155C-WHT Table Lamps
...le lamps
3ddd
lite source
http://www.lamps-lighting.com/lite-source/ls-21155c-wht.html
3dsmax 2013+2010+obj+.fbx+.3ds
Lot
3d_export
$15
parking lot
...parking lot
3dexport
desing from parking lot / diseño de estacionamiento
turbosquid
$3
Parket Lot
...bosquid
royalty free 3d model parket lot for download as c4d on turbosquid: 3d models for games, architecture, videos. (1273832)
turbosquid
$29
Parking Lot
...e 3d model parking lot for download as 3ds, obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1190823)
turbosquid
$10
Lampatron LOT
...3d model lampatron lot for download as max, max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1563025)
turbosquid
$15
Furniture Lot
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$65
Desert Lot
...del desert lot for download as 3ds, dxf, obj, x, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1147471)
3d_export
$65
parking lot
...parking lot
3dexport
simple rendering of the scene file
3d_export
$65
Parking lot
...parking lot
3dexport
simple rendering of the scene file
3d_export
$65
parking lot
...parking lot
3dexport
simple rendering of the scene file
3d_export
$65
Parking lot
...parking lot
3dexport
simple rendering of the scene file
7
turbosquid
$6
Rock 7-7
...urbosquid
royalty free 3d model rock 7-7 for download as obj on turbosquid: 3d models for games, architecture, videos. (1647866)
turbosquid
$8
Rock 7-7
...id
royalty free 3d model rock 7-7 for download as ma and fbx on turbosquid: 3d models for games, architecture, videos. (1693416)
design_connected
$16
No 7
...no 7
designconnected
sibast no 7 computer generated 3d model. designed by sibast, helge.
3ddd
$1
Team 7
...team 7
3ddd
team 7
моделилось с кталога team 7
3d_export
$5
hinge 7
...hinge 7
3dexport
hinge 7
turbosquid
$9
IS-7
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Calligraphic Digit 7 Number 7
...hic digit 7 number 7 for download as max, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1389338)
3ddd
free
team 7
...team 7
3ddd
team 7
стол фабрики team 7.
типы размеров /900,1000/x/1750,2000,2250/x/750/
раздвигается +600 или +1200
3ddd
$1
PLANTS 7
...plants 7
3ddd
цветы , горшок
plants 7.. hope u all enjoying the series
3ddd
$1
Pillows #7
...pillows #7
3ddd
подушка , pillows
pillows #7
3ds max 2011,fbx + textures
Included
turbosquid
$1
donut with display included
...free 3d model donut with display included for download as fbx on turbosquid: 3d models for games, architecture, videos. (1170714)
turbosquid
$25
Weapon - AWM - Included Highres
...ree 3d model weapon - awm - included highres for download as on turbosquid: 3d models for games, architecture, videos. (1533255)
turbosquid
$25
Weapon - M24 - Included Highres
...e 3d model weapon - m24 - included highres for download as ma on turbosquid: 3d models for games, architecture, videos. (1533263)
turbosquid
$39
man's shit (mannequin not included)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
free
the set includes a table and chair
...mless textures. table length 1.8 m width 0.8m height 0.55 m chair length 0.9m width 0.9m height 0.50m these objects are my ideas.
3d_ocean
$5
Coffee cups (scene included)
...ready to render (includes detailed,textured 2 coffee cups, lighting / texturing setup, render settings and post production -ea...
3d_export
$6
stylized - tutorial included
... just drop model into your scene and start rendering. no special plugin needed to open scene.<br>textures formats: png (2k)
turbosquid
$65
Tank T-72 (LODs Included)
...free 3d model tank t-72 (lods included) for download as blend on turbosquid: 3d models for games, architecture, videos. (1299434)
turbosquid
$19
The Studley Collection Desk Including Organizer
...on desk including organizer for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1153978)
turbosquid
$15
Design Elements including Golden Rooster
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
2
design_connected
$11
No 2
...no 2
designconnected
sibast no 2 computer generated 3d model. designed by sibast, helge.
turbosquid
$6
Cliff Rock 2-2
...uid
royalty free 3d model cliff rock 2-2 for download as obj on turbosquid: 3d models for games, architecture, videos. (1619161)
turbosquid
$29
Book variation 2 2
...3d model book variation 2 2 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1366868)
turbosquid
$22
Classic baluster (2) (2)
...assic baluster (2) (2) for download as max, obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1483789)
turbosquid
$99
Smilodon 2 Pose 2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Barrel Barricade 2-2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$6
Wall Trophy (2) (2)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Tire label 2 of 2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Кровать, 2 тумбочки, 2 светильника
...кровать, 2 тумбочки, 2 светильника
3ddd
кровать, 2 тумбочки, 2 светильника
нормальное качество
формат 3ds max
без текстур
3ddd
free
Кровать, 2 тумбочки, 2 светильника
...кровать, 2 тумбочки, 2 светильника
3ddd
кровать, 2 тумбочки, 2 светильника
нормальное качество
формат 3ds max
без текстур
Files
archibase_planet
free
File
...file
archibase planet
locker box archive
fp suspension file wh - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
free
File
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$5
Filing cabinet
...locker office paper storage store work
a simple but neatly-made filing cabinet, which ads a touch of relism to any office render.
turbosquid
$8
Filing cabinets
...id
royalty free 3d model filing cabinets for download as fbx on turbosquid: 3d models for games, architecture, videos. (1371140)
turbosquid
$8
File Cabinet
...squid
royalty free 3d model file cabinet for download as fbx on turbosquid: 3d models for games, architecture, videos. (1572208)
turbosquid
$16
Filing Cabinet
...ree 3d model filing cabinet for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1310873)
turbosquid
$2
File Cabinet
... free 3d model file cabinet for download as obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1357577)
turbosquid
$12
Nail File
...e 3d model nail file for download as blend, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1588508)
turbosquid
$5
File Organiser
...model file organiser for download as blend, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1636447)
turbosquid
$1
Flat file
...e 3d model flat file for download as 3ds, obj, md3, and blend on turbosquid: 3d models for games, architecture, videos. (1209808)