Thingiverse
Rack Mount System 19" by Masterkookus
by Thingiverse
Last crawled date: 3 years, 1 month ago
I am working on building a relay testing rack mount system and needed to have some custom brackets made. In designing them and printing them I have saved a significant portion of custom manufacturing costs.
Hardware Required:
6-32 1/4" length machine screws, Digikey H154-ND
6-32 1/2" length machine screws, Digikey H360-ND
2" Hex Standoffs 6-32 female-female, Keystone Electronics 2214, Digikey 36-2214-ND
1/2" Hex Standoffs 2-36 female-male, Keystone Electronics 8414, Digikey 36-8414-ND
Assembly:
Printed Parts
2 Panel_Mount
2 Center_Mount
2 Rear_Brackets (Modified to suit your needs)
2 Front_Plates (Modified to suit your needs)
? Rear_Mount_Vert/Horz if you need to mount terminal blocks or wiring harness
? Back_Plates (Modified to suit your needs)
First take the two Center_Mount pieces, insert four 2" standoffs into one of them, then press the second Center_Mount onto the exposed 2" standoffs ends. Use 6-32 screws to pull the spacer into the properly seated position.
1.1 Remove all screws from the completed center mount assembly that were used to seat the spacers.
Take the two Rear_Brackets and attach them to the center mount assembly using the 6-32 1/2" machine screws.
Insert 2" standoffs into the outer ends of the Rear_Brackets, secure these spacers using 6-32 1/2" machine screws.
Attach the two Panel_Mount pieces to the spacers that were just installed in the previous step, do not install any machine screws.
Next take the two front plates that you have used/designed and attach them to the Panel_Mount and Center mount assembly using 6-32 1/2" machine screws.
If using my Rear_Brackets they must be tapped, perform this using a 6-32 tap, take care to clean the tap after the completion of each hole. At this time it would also be beneficial to tap the small holes in the Rear_Mount_Horz/Vert as well.
Install the 1/2" Standoffs to the Rear_Bracket tapped holes, the purpose of the standoffs is to allow additional room for wire/cable management.
Depending on if you are using horizontal or vertical back plates, install the appropriate Rear_Mount to the standoffs and secure using 6-32 1/4" machine screws.
Install the Back_Plates to the Rear_Mounts using 6-32 1/4" machine screws
Changes:
4/8/2017: Added a 45 degree angled terminal block rear mounting bracket, have not tested yet.
Hardware Required:
6-32 1/4" length machine screws, Digikey H154-ND
6-32 1/2" length machine screws, Digikey H360-ND
2" Hex Standoffs 6-32 female-female, Keystone Electronics 2214, Digikey 36-2214-ND
1/2" Hex Standoffs 2-36 female-male, Keystone Electronics 8414, Digikey 36-8414-ND
Assembly:
Printed Parts
2 Panel_Mount
2 Center_Mount
2 Rear_Brackets (Modified to suit your needs)
2 Front_Plates (Modified to suit your needs)
? Rear_Mount_Vert/Horz if you need to mount terminal blocks or wiring harness
? Back_Plates (Modified to suit your needs)
First take the two Center_Mount pieces, insert four 2" standoffs into one of them, then press the second Center_Mount onto the exposed 2" standoffs ends. Use 6-32 screws to pull the spacer into the properly seated position.
1.1 Remove all screws from the completed center mount assembly that were used to seat the spacers.
Take the two Rear_Brackets and attach them to the center mount assembly using the 6-32 1/2" machine screws.
Insert 2" standoffs into the outer ends of the Rear_Brackets, secure these spacers using 6-32 1/2" machine screws.
Attach the two Panel_Mount pieces to the spacers that were just installed in the previous step, do not install any machine screws.
Next take the two front plates that you have used/designed and attach them to the Panel_Mount and Center mount assembly using 6-32 1/2" machine screws.
If using my Rear_Brackets they must be tapped, perform this using a 6-32 tap, take care to clean the tap after the completion of each hole. At this time it would also be beneficial to tap the small holes in the Rear_Mount_Horz/Vert as well.
Install the 1/2" Standoffs to the Rear_Bracket tapped holes, the purpose of the standoffs is to allow additional room for wire/cable management.
Depending on if you are using horizontal or vertical back plates, install the appropriate Rear_Mount to the standoffs and secure using 6-32 1/4" machine screws.
Install the Back_Plates to the Rear_Mounts using 6-32 1/4" machine screws
Changes:
4/8/2017: Added a 45 degree angled terminal block rear mounting bracket, have not tested yet.
Similar models
thingiverse
free
GoPro Scope Mount by Printmaster98
...t.
3) glue the "gopro bracket" to the "scope mount lower".
(abs glue is recommended) super glue works fine.
grabcad
free
Battery Clip/Holder, Keystone 54, 254
...abcad
battery clip/holder, keystone 54 & 254
2 configurations w/i the solidworks model
digikey pn's: 36-54-nd, 36-254-nd
thingiverse
free
Optical mount for lens / mirror / prism by dmarett
..." screws
1 6-32 x 3/4" screw (ball mount)
2 1/2" springs with hook ends
4 7/16" x 1/16" aluminum pins
thingiverse
free
Pi Camera Telescope Mount by scottpreston
...ed 2mm screws to mount the camera to the base. i used 6-32 1" standoffs with 6-32 3/8" socket head cap screws to mount.
grabcad
free
PTFE INSULATED TERMINAL 11158
...ptfe insulated terminal 11158
grabcad
keystone electronics
ptfe insulated terminal 11158
digikey: 36-11158-nd
grabcad
free
Keystone #4334 6-32 Bracket
... file and step file provided.
buy it here:
https://www.digikey.com/product-detail/en/keystone-electronics/4334/36-4334-nd/316182
thingiverse
free
Post holder 2 inch and 1/2 inch dia. post by dmarett
...inned at the desired height by a thumb knob with an 8-32 thread. the post holder thumb know hole needs to be threaded before use.
thingiverse
free
1/2" Coro PVC Mount by scooter_seh
...ps. #6 sheet metal screw is used with "1-2 pvc mount.stl" #6 machine screw is used with "1-2 pvc mount_2.stl"
thingiverse
free
Iphone 6 timelapse mount by Cjoutwest
...clips or some other kind of clip that is similar i use 4 on my printer, 1 on each...
thingiverse
free
Morserino Case by flymustangs
...d.
i just use a 3mm screw to "thread" the standoffs. a normal tap seems to melt the plastic and not provide a good tap.
Masterkookus
thingiverse
free
Ziploc Weathertight Handle by Masterkookus
... by masterkookus
thingiverse
bought a container for filament storage and was missing a handle, so tried to design a replacement.
thingiverse
free
Zip Tie Brackets by Masterkookus
...zip tie brackets by masterkookus
thingiverse
simple zip tie brackets i printed up for rope and string lights.
thingiverse
free
Joining biscuits by Masterkookus
...thingiverse
i needed some biscuits for a shelf project and didn't feel like buying a box, so printed these in wood filament.
thingiverse
free
Wrench Rack by Masterkookus
...y masterkookus
thingiverse
just a simple rack i designed to hold some old wrenches i purchased from harbor freight 12 years ago.
thingiverse
free
Tap Wrench Rack by Masterkookus
...tap wrench rack by masterkookus
thingiverse
a rack designed to hold the harbor freight 3 pc t-handle tap wrench set
thingiverse
free
Nut Driver Rack by Masterkookus
...nut driver rack by masterkookus
thingiverse
nut driver rack for harbor freight 7 pc metric/sae nut driver set.
thingiverse
free
Hole Plugs by Masterkookus
... hole plugs for a few select sizes
1/24/2019: added fusion360 backup files, i would like to make a generator for it one day soon.
thingiverse
free
Plate Stand by Masterkookus
...bout 9" diameter. the fusion360 archive files are attached so that you can add the mounting holes for the hinge you select.
thingiverse
free
Rope Light Brackets by Masterkookus
... masterkookus
thingiverse
clips i made for 8mm (harbor freight) rope lights, brackets were secured with a #4 1/2 inch wood screw
thingiverse
free
PHIL - Stand by Masterkookus
...ces and 6-32 inserted nuts to either secure to a platform or to apply rubber "feet" as i have.
hope you find it useful.
19
3d_export
$15
rocks 19
...rocks 19
3dexport
rocks 3d model 19
3d_export
$50
covid-19
...covid-19
3dexport
3d obj model. covid-19
3ddd
$1
PLANTS 19
...plants 19
3ddd
цветок , горшок
plants 19.. enjoy
3d_export
$11
covid-19
...covid-19
3dexport
this is 3d model about covid-19 virus
turbosquid
$25
COVID-19 coronavirus-19 virus microorganism
...virus-19 virus microorganism for download as ma, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1598091)
3ddd
$1
Curtains 19
...curtains 19
3ddd
ламбрекен
curtains 19
other models:http://3ddd.ru/users/brast/models
3d_export
$5
covid-19 korona
...covid-19 korona
3dexport
covid-19
3d_export
$6
tap-19
...tap-19
3dexport
3d_export
$8
coronavirus covid-19
...coronavirus covid-19
3dexport
coronavirus covid-19
3d_export
$5
coronavirus covid-19
...coronavirus covid-19
3dexport
coronavirus covid-19
Rack
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 6 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 3 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 5 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...ack
archibase planet
rack paper rack rack for paper
rack 7 office n060914 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...for magazines rack for notebooks notebooks notebook
rack notebook n120614 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack umbrella umbrella rack
rack n180811 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack book rack stand
rack - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack rack for glasses
rack 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Rack
...rack
archibase planet
rack rack for glasses
rack 2 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
free
rack
...rack
3dexport
rack
System
archibase_planet
free
System
...m
archibase planet
fire alarm system fire alarm box
security light system - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Spider system
...stem spider glass system
spider system to fix glass stefano galli n050912 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
Euforia System
...euforia system
3ddd
euforia
euforia system
3d_export
$50
Roof system Truss system 3D Model
...oof system truss system 3d model
3dexport
roof system truss truss stage
roof system truss system 3d model aleksbel 38970 3dexport
3ddd
$1
DVD System
...dvd system
3ddd
dvd , schneider
dvd system
design_connected
free
Seating system
...seating system
designconnected
free 3d model of seating system
3d_export
$5
solar system
...solar system
3dexport
solar system in c4d, with 8k nasa textures
3ddd
$1
Quanta System
...quanta system
3ddd
медицина
quanta system.
лазерное оборудование для медицинских центров
3d_export
$15
solar system
...nd the other the sun, the earth and the moon, the latter has an animation with camera movement included, the files are in spanish
3d_export
$14
missile system
...missile system
3dexport
Mount
3d_export
free
mounting bracket
...mounting plate is the portion of a hinge that attaches to the wood. mounting plates can be used indoors, cabinetry and furniture.
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)