Thingiverse
quadrocopter by yoveo
by Thingiverse
Last crawled date: 2 years, 12 months ago
a very easy to print quadcopter. you'll need:
aluminium profile 10x10mm (I used 2x 500mm length)
KK2.0 flight controller
Q Brain 4 x 20A Brushless Quadcopter ESC 2-4S 3A SBEC
4x Turnigy 1100KV Brushless Motors
NIMH/LiPo Battery
4 Channel Sender/Reciever
You will have to use araldite or similar glue to glue in the aluminium profiles into the base and motor mount.
print with 0.8mm wall thickness, 40% infill:
2x base
4x motormount
1x controller
1x batteryholder_a
1x batteryholder_b
2x foot_30mm
2x foot_40mm
Assembly as shown in build_complete.stl
This is a work in progress... Detailed infos and additional parts follow... (though it is flyable as it is!)
Update 1:
I just added a prototype of the landing gear. the battery holder is right now fit for a 8 cell nimh battery but will soon be replaced by a lipo pack...
Update 2:
I added build_complete as a 3d build instruction (not meant for printing)
Update 3:
I wasn't happy with the motor mounts and feet so I redesigned them. Tested the quadracopter today and the flight was great! I'm quite happy with the current design but I'm waiting for my LiPo battery to arrive... The redesign also results in having to print less items.
aluminium profile 10x10mm (I used 2x 500mm length)
KK2.0 flight controller
Q Brain 4 x 20A Brushless Quadcopter ESC 2-4S 3A SBEC
4x Turnigy 1100KV Brushless Motors
NIMH/LiPo Battery
4 Channel Sender/Reciever
You will have to use araldite or similar glue to glue in the aluminium profiles into the base and motor mount.
print with 0.8mm wall thickness, 40% infill:
2x base
4x motormount
1x controller
1x batteryholder_a
1x batteryholder_b
2x foot_30mm
2x foot_40mm
Assembly as shown in build_complete.stl
This is a work in progress... Detailed infos and additional parts follow... (though it is flyable as it is!)
Update 1:
I just added a prototype of the landing gear. the battery holder is right now fit for a 8 cell nimh battery but will soon be replaced by a lipo pack...
Update 2:
I added build_complete as a 3d build instruction (not meant for printing)
Update 3:
I wasn't happy with the motor mounts and feet so I redesigned them. Tested the quadracopter today and the flight was great! I'm quite happy with the current design but I'm waiting for my LiPo battery to arrive... The redesign also results in having to print less items.
Similar models
thingiverse
free
High-Speed Planing RC Boat by awseiger
...l the cable holes in with hot glue or epoxy. i recommend hot glue, as it can be re-heated to allow for replacement of the motors.
grabcad
free
65mm Frame 615 Brushed Motors
... stick out. some people use velcro and don't need the tabs at all. you have options!
the photos show how i placed everything.
thingiverse
free
Drone Quadcopter by SmartBlug
...
1x 11.1v 5200mah 30c lipo lion battery
1x radio system receiver
available here:https://cults3d.com/fr/jeu/drone-quadcopter
thingiverse
free
Delta wing motor mount by coldmake
...ation screws is 16 mm.
you need to print:
1x base
1x motor
2x side
assembly:
just click it together and secure it with superglue.
thingiverse
free
Arduino multiwii quadcopter by cescmentation_folch
...p flight controller w/ftdi & dsm2 port (1x)
other material:
-380 mm long aluminium bar with square section of 10 mm side (4x)
grabcad
free
X4 Quadcopter
... models from grabcad community like brushless motors, props, camera (thanks a lot!).
any questions i will reply in the comments.
thingiverse
free
Quadcopter undercarriage Lipo battery mount by chriseslick
...secure the battery. the mount attaches to the inner outrigger screws. 4x m3 10mm screws are required to mount the battery holder.
thingiverse
free
Budget and Better than DJI! 3D Printed/ Laser Cut 10" Drone
...he nuts in place.
electronics i used:
4x t-motor 2216 11 900kv motors
mamba f405 stack
bn880 gps
bmp280 barometer
4000mah 3s lipo
thingiverse
free
Brushless Whoop Quadcopter by RalphHilton
...fc and 4 in 1 esc.
i used 4 8mm nylon spacers between the top and bottom sections.
tx01 camera mount. battery housing.
5cm props.
thingiverse
free
Quadcopter F450 frame enclosure by Maker023
...e to attach the gps to the base. the base should snap on.
if you have any questions, please let me know. i will be happy to help.
Quadrocopter
3d_export
$5
Quadrocopter
...quadrocopter
3dexport
quadrocopter
3d_export
$50
quadrocopter
...quadrocopter
3dexport
assembled quadrocopter according to an individual concept.
turbosquid
$10
Quadrocopter
... free 3d model quadrocopter for download as 3ds, obj, and c4d on turbosquid: 3d models for games, architecture, videos. (1390839)
turbosquid
$45
Quadrocopter drone
...odel quadrocopter drone for download as c4d, max, ma, and fbx on turbosquid: 3d models for games, architecture, videos. (1608857)
turbosquid
$19
Drone Quadrocopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
cg_studio
$55
Drone Quadrocopter With Camera Rigged3d model
....fbx .max .3ds - drone quadrocopter with camera rigged 3d model, royalty free license available, instant download after purchase.
3d_ocean
$29
3D quadrocopter DJI Phantom 2 model
...the model contains animations. you get 3d model with 11 v-ray materials with hdri. also you get 3 high resolution 1920...
3d_ocean
$29
Drone Quadrocopter With Camera Rigged
...ry with turbosmooth in history. all object rigged or linked to easy manipulate. 3 special controller for camera rotation in 3 ...
3d_export
$30
LotusRC T580 quadcopter 3D Model
...lotusrc t580 quadcopter 3d model 3dexport lotusrc t580 quadrocopter drone copter helicopter quadrotor quadcopter quad rc camera go...
3d_ocean
$19
Hovercopter (concept)
...hovercopter (concept) 3docean concept helicopter hover bike prototype quadrocopter you probably heard about the hover bike. of course...