Thingiverse
QAV 400 Dragonlink Receiver Bracket by Mochaboy
by Thingiverse
Last crawled date: 3 years ago
This is a mounting bracket I printed off for my QAV400. The bottom plate has 2 sets of 4 holes which I think were originally intended for mounting landing gear, but otherwise go unused.
You'll need 4 - M4 nuts and screws. I purposely made the nut hole a little undersized because the nuts get melted in place to lock them in permanently. Use a soldering iron to heat the nut and press into place.
This mounting bracket was part of a series of modifications to relocate the UHF transmitter as far away from the other RF emitting sources. Scanning with a spectrum analyzer showed slightly better noise levels below the rig than above the rig which is what led to this being located where it is.
I've attached the SKP file in case you need to make any changes to it.
One other note - it's hard to make out in the photo but I soldered in a 300ma 5v step down regulator from Pololu into the power distribution board and routed the wires right to the bracket so you can power the receiver from a separate power source.
Quite a few folks have reported dropouts and motor cutoffs so the current recommendation is to power the UHF receiver separately from the CC3D. If that's not possible, power the receiver directly from a 5v source, then connect a set of jumper cables from the receiver to the power pins of the CC3D, not the other way around.
You'll need 4 - M4 nuts and screws. I purposely made the nut hole a little undersized because the nuts get melted in place to lock them in permanently. Use a soldering iron to heat the nut and press into place.
This mounting bracket was part of a series of modifications to relocate the UHF transmitter as far away from the other RF emitting sources. Scanning with a spectrum analyzer showed slightly better noise levels below the rig than above the rig which is what led to this being located where it is.
I've attached the SKP file in case you need to make any changes to it.
One other note - it's hard to make out in the photo but I soldered in a 300ma 5v step down regulator from Pololu into the power distribution board and routed the wires right to the bracket so you can power the receiver from a separate power source.
Quite a few folks have reported dropouts and motor cutoffs so the current recommendation is to power the UHF receiver separately from the CC3D. If that's not possible, power the receiver directly from a 5v source, then connect a set of jumper cables from the receiver to the power pins of the CC3D, not the other way around.
Similar models
thingiverse
free
Anet A8 Mounting Bracket for a MeanWell NES-350-12 Power Supply by mskressin
...bracket to the power supply. then you can simply put the m3 screws through the existing holes in the frame to attach the bracket.
thingiverse
free
Prusa Power Supply Mounting Bracket by LittleDangerous
...ve 4 holes on the bottom, so i designed a combination of brackets to fit each unique mounting situation.
source files inside zip.
thingiverse
free
TomTom CD Slot Mount With Ball Joint by Gadget08
...in use as shown. one of the brackets as you can see i didn't print, the smooth shiny j bracket but i have added one to print.
thingiverse
free
Raspberry Pi headless server case
...al)
1x 6mm power switch (optional)
1x 40x40x10mm 5v fan (optional)
3-pin female connector
wires (suggested: red 10cm, black 10cm)
thingiverse
free
Quanum RC540R 5.8Ghz RX Mount by bmsweb
...ke a 3d printed part like the one in the image.
the orange part i need to find on my computer, once i do, i'll upload it here
thingiverse
free
IP Camera Non-Invasive Mounting Bracket
...n holes.
mounting holes are 3mm (m3) which matches the mounting bracket.
i can design for other dimentions if you make a request.
thingiverse
free
Meanwell LRS-150-12 Power Supply Mounting Brackets by USWaterRockets
...on a monoprice select mini 3d printer. you can see how it was done on our hack-a-day page here: https://hackaday.io/post/48839/
thingiverse
free
Joyo Power 4 pedal board power supply mount bracket by Cameronspg
...the case together hold the power supply into the bracket (i substituted longer bolts, but i don't know what thread they are).
thingiverse
free
Migbot Adjustable Z Sensor mount remix by veaceonee
... iron to "smoosh" the nut into the cavity. there by encapsulating the nut and making it a permanent part of the mount.
thingiverse
free
Prusa i3 Y Motor Bracket Adapter by NoenDex
...e 3 mm nuts to push them into the plastic not to block the rods. as a side effect of that is they a sealed good into the plastic.
Mochaboy
thingiverse
free
Armattan Morphite Legs / Landing Gear by Mochaboy
...phite 180mm quadcopter available here:
http://www.armattanminis.ca/
screw hole is inset 8mm deep and designed for an m3 screw
thingiverse
free
Armattan Morphite 180 Clip on Battery Bracket by Mochaboy
... enables me to strap a 1300mah 40c battery that weighs about 109g and shift it's position to get the right center of gravity.
thingiverse
free
QAV 400 Feet by Mochaboy
...ro dynamics.
you'll need 2 mini zip ties to attach each foot - the holes are 3mm wide so make sure you have the right size.
thingiverse
free
Mochaboy's "Tool less" Tensioner Printrbot Jr / XL and GT2 belts by Mochaboy
...)
i found that after about 50 hours on my printer, it needed a belt adjustment - the knobs make this effortless now :)
enjoy!
thingiverse
free
Armattan Morphite 10 degree Camera Seat by Mochaboy
...t it works very well.
this part was designed for an armattan morphite 180mm quadcopter. will update it when the build is done.
thingiverse
free
Fatshark Battery Case for 18650 Batteries by Mochaboy
...ils or headers and crimps and some 26awg silicone wire. pigtails are quite common on ebay just search for 2s balance connectors.
thingiverse
free
Vibration Isolating Silicone Dampers by Mochaboy
.....then let it sit and cure. once it's cured - remove the top of the mold then trim with a sharp pair of scissors.
enjoy :)
thingiverse
free
PZ0420 / 600TVL Board Camera Housing by Mochaboy
...e the swivels and over time i may incorporate curved edges. i'll be adding front plates for other cameras as well over time.
thingiverse
free
QAV-500 UHF Rx mount by bobunobu
...rx mount by bobunobu thingiverse this is based on mochaboy qav-400 uhf antenna bracket: http://www.thingiverse.com/thing:152510 i made this to...
Dragonlink
thingiverse
free
DragonLink antenna protector by Alextattoo
...ector by alextattoo
thingiverse
this is protector for dragonlink 433mhz antenna. the end with the arrow should be mounted upside
thingiverse
free
ADVANCED RX DRAGONLINK MOUNT
...advanced rx dragonlink mount
thingiverse
advanced rx large dragonlink mount >>> push & click
thingiverse
free
Dragonlink mini RX case by armyatcdude
...dragonlink mini rx case by armyatcdude
thingiverse
here is a case for a dragonlink mini rx receiver. enjoy!
thingiverse
free
Dragonlink V2 Cradle by brentd
...dragonlink v2 cradle by brentd
thingiverse
nice snug fit.
thingiverse
free
DragonLink V3 case by robinbw
...ink v3 transmitter, it uses the mounting bracket from dl. i have included the dwg file if anyone wants to make mods. happy fpving
thingiverse
free
Dragonlink v2 Upright cradle by Matador2k7
...link v2 rx upright after i added a notch filter. it was no longer practical to have it mounted sideways on my radio tx fpv frame.
thingiverse
free
Frsky Horus x12s Mount for Dragonlink V2 Transmitter by tomausteltow
...frsky horus x12s mount for dragonlink v2 transmitter by tomausteltow
thingiverse
tiny mount for dragonlink on your x12s horus.
thingiverse
free
Dragonlink Transmitter Mount by Toombinator
...ther transmitters, especially the taranis.
included inventor .ipt files and the assembly .iam file if you need to change things.
thingiverse
free
Dragonlink Transmitter Antenna Cap by vi3telit3
... the antenna can then be stowed in a bag safely and nothing can mess up the pin inside the antenna. print with flexible filament.
thingiverse
free
Dragonlink V3 slim Module stand for Taranis by Blacksea
...onlink v3 slim stand for jr type modules , allows connection of trainer cord for head trackers to the trainer socket on the back.
Qav
thingiverse
free
QAV-R/QAV-210/QAV-180/Generic Quad Landing Pad by tes4p00ner
...qav-r/qav-210/qav-180/generic quad landing pad by tes4p00ner
thingiverse
this is a replacement qav-r landing pad.
thingiverse
free
QAV-R Antenna Tube Holder and Antenna Caps For QAV-R, QAV 210, and QAV 180 by jason51873
...caps for qav-r, qav 210, and qav 180 by jason51873
thingiverse
print this with flexible material and slide over rear stand offs.
thingiverse
free
QAV-250 by Hermes1229
...qav-250 by hermes1229
thingiverse
qav-250
thingiverse
free
Foxeer_switcher Mount for QAV-X and QAV-210 by NyeinChanZaw
... is the mount for foxeer switcher vtx. it can be used in qav 210, qav x or others which have 31mm distance between two stand off.
thingiverse
free
qav 210 by Ravvinoff
...qav 210 by ravvinoff
thingiverse
racing drone qav 210
thingiverse
free
Support Runcam Skyplus for QAV-R OR QAV 210 by Strangers
...trangers
thingiverse
support for mounting runcam skyplus on qav-r or qav 210 180.
added version with bumper for 2.1 and 2.5 lens
thingiverse
free
Lumenier Action Camera Mount Vibration Dampening Pins and Circlips (QAV-180 QAV-210 QAV-R ) by tes4p00ner
...pro 250 pin and circlips by alessandroame, in order to fit the lumenier qav-r / qav-180 / qav-210 gopro / mobius / runcam mount.
thingiverse
free
Lumenier QAV-S QAV S Hero 8 Hero8 mount by sun573
...lumenier qav-s qav s hero 8 hero8 mount by sun573
thingiverse
hero 8 mount remixed for the qav s
thingiverse
free
nox5" and qav-x and qav-r session mounts by MichaelJFPV
...nox5" and qav-x and qav-r session mounts by michaeljfpv
thingiverse
make in tpu super slow
thingiverse
free
QAV-R / QAV 210 Go Pro Mount by Mr_Anderson88
...qav-r / qav 210 go pro mount by mr_anderson88
thingiverse
printed out of tpu to absorb vibrations.
400
design_connected
$11
400
...400
designconnected
artek 400 armchairs computer generated 3d model. designed by alvar aalto.
3d_export
$17
Boeing-747-400
...boeing-747-400
3dexport
boeing-747-400
turbosquid
$249
Boeing767 400
...quid
royalty free 3d model boeing767 400 for download as max on turbosquid: 3d models for games, architecture, videos. (1635314)
turbosquid
$25
B747-400
...uid
royalty free 3d model boeing 747-400 for download as skp on turbosquid: 3d models for games, architecture, videos. (1260135)
3ddd
$1
Armchair 400
... tank
the armchair 400, designed by alvar aalto in 1936 and better known as tank.
pelt coat idea by studioilse.
3ddd
$1
Weinsberg Caraone 400
...weinsberg caraone 400
3ddd
прицеп
weinsberg caraone 400
салона нет, все окна прикрыты шторами.
3ddd
free
Розетка d-400
...розетка d-400
3ddd
розетка
диаметр: 400 мм
производитель: мастер гипс
код товара: 50rz_009gp
3d_export
$59
B747 400 3D Model
...b747 400 3d model
3dexport
aircraft jumbo b747-400 star alliance b744 jetplane jet 747
b747 400 3d model puma83ffm 7898 3dexport
3ddd
$1
Goossen licht Zeppel 400
...goossen licht zeppel 400
3ddd
goossen licht , zeppel
goossen licht zeppel 400
3ddd
$1
Jotul I 400 FL
...jotul i 400 fl
3ddd
jotul , камин
jotul i 400 fl
jotul.com
Receiver
archibase_planet
free
Receiver
...receiver
archibase planet
receiver receiving set radio set
receiver n170311 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Receiver
...receiver
archibase planet
receiver equipment
receiver - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Receiver
...receiver
archibase planet
radio tuner receiver
receiver n120108 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Receiver
...receiver
archibase planet
receiver denon
denon avr3805- 3d model for interior 3d visualization.
turbosquid
$62
RECEIVER
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$40
Receiver
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$6
Receiver for 20m3
...receiver for 20m3
3dexport
receiver for 20m3 of compressed air
archive3d
free
Receiver 3D Model
...iver receiving set radio set
receiver n170311 - 3d model (*.3ds) for interior 3d visualization.
3d_ocean
$6
DVD Receiver
...yer. can also be used as a receiver. original design dvd player or stereo design with exceptional detail. dvd receiver 3d models.
3d_ocean
$25
Television receiver
...cial plugin needed to open scene. - correctly scaled accurate representation of the original objects. - model is all materials...
Bracket
archibase_planet
free
Bracket
...bracket
archibase planet
bracket corbel holder
bracket 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
bracket corbel console
bracket 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
corbel holder bracket
bracket 6 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
bracket corbel console
bracket 8 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
bracket corbel holder
bracket n280911 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
holder corbel bracket
bracket 9 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
corbel holder bracket
bracket 10 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
corbel console bracket
bracket 11 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
holder console bracket
bracket 12 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bracket
...bracket
archibase planet
bracket corbel holder
bracket 13 - 3d model (*.gsm+*.3ds) for interior 3d visualization.