Thingiverse
PXFlow Mount by simondlevy
by Thingiverse
Last crawled date: 3 years, 1 month ago
This plate allows you mount a PX4Flow optical flow / sonar unit on the bottom of a miniature aerial vehicle. Four M3 nylon screws (approx 6mm long) and 5mm standoffs allow you to remove the unit as needed. You can glue the mount to the bottom of your vehicles frame with E6000.
Similar models
thingiverse
free
DJI Air Unit Mount for other RC Applications
... built into the bottom to allow you to use straps to affix it to your rc vehicle, whether it be a plane or a car, or even a boat.
thingiverse
free
Google Home Wall Mount by RobsVirtualCave
...
google home wall mount. this item will require 2 x 10mm magnets to allow you to attach the bottom part of the unit to the top.
thingiverse
free
DJI Air Unit Mount / Holder for Digital FPV System VTX by thedoble
...ver the top of the air unit.
i use some double-sided tape on the bottom.
i print the unit in petg on it's edge with supports.
thingiverse
free
Kitchen unit plinth clip by Glyn
...to make your own plinth, i.e. the blank plate at the bottom of a kitchen unit, then this will allow you to attach it to the legs.
thingiverse
free
SG90 Servo Case by renzema
...m for drilling.
there are channels in the case and bottom for the servo wire.
fit for the servo into the base is by friction only
thingiverse
free
Garmin Bottom Light Mount by camazusa
...er cylinder that allows you to mount under your garmin gps any accessory that would otherwise be mounted to your bike handlebars.
grabcad
free
Tripod Camera Mount
...tripod camera mount
grabcad
a component screwed into the bottom of a digital camera to allow it to be mounted to a tripod
thingiverse
free
RadioMaster TX16S ImmersionRC PowerPlay Mount by karlpablo
...rlpablo
thingiverse
allows you to mount your powerplay dvr to your tx16s pots. use double-sided tape on top, optional on bottom.
3dwarehouse
free
Heliatos Solar Bottom Feed Connector V.2
...ain valve allows you to drain the unit normally. #hybrid_solar_water_heater #solar #solar_water #solar_water_heater #water_heater
thingiverse
free
Taranis Antenna Bracket by Dale_w
...he bottom bracket are 2.5mm to allow for tapping in a thread.
this was inspired by this https://www.thingiverse.com/thing:2327649
Simondlevy
thingiverse
free
130mm quadcopter frame by simondlevy
...130mm quadcopter frame by simondlevy
thingiverse
130mm quadcopter frame for 36mm flight controllers.
thingiverse
free
Long Hot Legs by simondlevy
...long hot legs by simondlevy
thingiverse
70mm legs for zmr250 250mm quadcopter -- when you need a little extra clearance!
thingiverse
free
MaxBotix sonar mount for quadcopter by simondlevy
...adcopter by simondlevy
thingiverse
use this mount in conjunction with http://www.thingiverse.com/thing:1250391 for easy removal.
thingiverse
free
LidarLite mount for quadcopter by simondlevy
...sensor to the bottom of a quadcopter. attach m3 nylon bolts and standoffs, then glue onto quadcopter with e6000 "goop"
thingiverse
free
HiTEC 5645MG Servo Mount by simondlevy
...
this is a bracket for mounting a hitec 5644mg high-torque servo to a flat surface. it will probably fit many other servos too.
thingiverse
free
IQuad Mark III by simondlevy
...amp; lee iq center, by iq center director dave pfaff. vertical posts support infrared-reflective spheres used in motion capture.
thingiverse
free
Tabbed Leg for mini quadcopter by simondlevy
...faff (washington & lee university) and a suggestion by bert wagner (a2usa, inc.) use e6000 ("goop") to secure tab.
thingiverse
free
ODROID U-3 platform for 250mm quadcopter by simondlevy
...imondlevy
thingiverse
connects a hobbyking power distro board to a 36mm flight controller (naze, cc3d, flip32) and an odroid u-3
thingiverse
free
Quanum Pico mount for Syma X5C by simondlevy
... you must first remove the existing flight controller from the x5c before attaching the plate, using e6000 or a similar adhesive.
Mount
3d_export
free
mounting bracket
...mounting plate is the portion of a hinge that attaches to the wood. mounting plates can be used indoors, cabinetry and furniture.
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)