Thingiverse
Prusa Rework X-Carriage for LM8LUU by GiulianoM
by Thingiverse
Last crawled date: 3 years, 1 month ago
Designed a new X-Carriage for the Prusa Rework (1.0 or 1.5), meant to be used with the longer LM8LUU linear bearings (8x15x45mm).
You can optionally use this with 4 x LM8UU bearings, but they'll stick out a few mm.
The carriage block is designed to be strong, yet simple.
The bearings are press-fit into the holes, and then (optionally) retained by 4 x M3-10mm screws and M3 washers. You'll need to take apart your X and Z axis to install this.
The back of the block has recessed holes for the socket head cap screws.
You will need:
4 x M4-30mm socket head cap screws, to mount the extruder.
2 x M3-20mm socket head cap screws, to attach the X-axis belt.
The 2x M3 screws are used to secure the ends of the X-carriage belt:
At each end of the belt, form a loop with the teeth facing in - the length of the loop should be about 18-20mm. Clamp the loop with two zip-ties on each end.
Insert one end of the loop into the block, and insert one of the M3 screws through the loop to secure it.
Repeat the same for the other side, and then tension the belt.
You can optionally use this with 4 x LM8UU bearings, but they'll stick out a few mm.
The carriage block is designed to be strong, yet simple.
The bearings are press-fit into the holes, and then (optionally) retained by 4 x M3-10mm screws and M3 washers. You'll need to take apart your X and Z axis to install this.
The back of the block has recessed holes for the socket head cap screws.
You will need:
4 x M4-30mm socket head cap screws, to mount the extruder.
2 x M3-20mm socket head cap screws, to attach the X-axis belt.
The 2x M3 screws are used to secure the ends of the X-carriage belt:
At each end of the belt, form a loop with the teeth facing in - the length of the loop should be about 18-20mm. Clamp the loop with two zip-ties on each end.
Insert one end of the loop into the block, and insert one of the M3 screws through the loop to secure it.
Repeat the same for the other side, and then tension the belt.
Similar models
thingiverse
free
LM8LUU Bearing Blocks for Prusa Y-Axis by GiulianoM
...the blocks to the y-carriage. 20mm are long enough if your plate is threaded - use 25-30mm with nuts if yours is drilled through.
thingiverse
free
Y Axis Idler (Heavy-duty) by TK_DESIGN
...y axis idler (heavy-duty) by tk_design
thingiverse
for prusa i3 rework
parts
hex socket head cap screw
m3 x 20mm x 4
nut
m3 x 4
thingiverse
free
Blacktooth laser cutter X-axis belt end block by MurphysLawyer
...ot holes first!).
the .stl file can be opened with cura or repetier-host. the .skp file can be opened and modified in sketchup.
thingiverse
free
Hephestos Prusa i3 X Carriage by Hakulukiam
...can use the original m3*10 screws.
various improvments to reduce overhang.
changed hole of the thogh belt clip to fit a m3 screw
thingiverse
free
i3 Rework X-Carriage for LM8LUU (geeetech) by djask
...ginal prusa rework carriage modified to use lm8luu bearings.
two files for geeetech with endstop and other for standard carriage.
thingiverse
free
Cherry pi III Mini V Wheel Carriage for OpenBuild with Cable tightener by mikes3ds
...ointys design 8mm balls, and for the rexroth/motedis see this link.http://forums.reprap.org/read.php?178,361141,470341#msg-470341
thingiverse
free
HicTop Prusa i3 X Axis End Cap by Duc76
...hole straight through the x axis and the protruding portion of the cap with a m5 socket head to secure it. but, my plans changed.
thingiverse
free
X Slide T Belt Adjuster by G3DBuilder
...equested. the pma clamp utilizes 2-56 x 1/2" screws for the top cover and 4 m4 x 8mm to attach to the linear bearing blocks
thingiverse
free
Prusa MK2 x carriage LM8LUU by stefanino
...prusa mk2 x carriage lm8luu by stefanino
thingiverse
prusa mk2 x carriage with lm8luu bearings
thingiverse
free
Bushing holder for 20mm hole-separation by misan
...the holder and the holder has nut-traps for m3 that with 12mm m3 screws will allow the part to be securely fixed to the carriage.
Giulianom
thingiverse
free
Lumia 640 Mount by GiulianoM
...l shrink to the correct size. abs will also more likely resist high temperatures in a car, so i wouldn't recommend using pla.
thingiverse
free
Dust Collector Blower to 6" Duct by GiulianoM
...l fit in sdr pipes of slightly varying diameters.
used for venting the blower outside or otherwise into some other 6" input.
thingiverse
free
4" x 6" Oval Hole Template by GiulianoM
... 7", and the distance between the two walls is 6.04".
clamp it down over a 6" board and the oval will be centered.
thingiverse
free
MicroSwiss Ender 5 Plus Direct Drive Plate by GiulianoM
...ve-extruder-for-creality-ender-5
i am using the stl to design a cooling shroud since there are extra mounting holes on the plate.
thingiverse
free
Dial Indicator Mount for MGN12H Linear Block by GiulianoM
...m3 10mm screws for mounting the adapter block to the mgn12h carriage.
1 x m3 screw, 10-15mm long for securing the dial indicator.
thingiverse
free
Arducam 5MP OV5647 Camera Mount by GiulianoM
...e should come with the camera kit.
if not, you'll need 4 x m2 15mm screws and 4 x m2 nuts.
m2 - 2mm screws, not m2.5 - 2.5mm.
thingiverse
free
LM8LUU Bearing Blocks for Prusa Y-Axis by GiulianoM
...the blocks to the y-carriage. 20mm are long enough if your plate is threaded - use 25-30mm with nuts if yours is drilled through.
thingiverse
free
i3 Z-Ends for LM8LUU and 8mm Anti-Backlash Nut by GiulianoM
...44
these are the z-end parts that correspond with the x-ends i designed:http://www.thingiverse.com/thing:1060956
work in progress
thingiverse
free
Mini Height Differential IR Sensor Board Mount for E3D v6 / Prusa i3 Rework by GiulianoM
...t onto the bottom two m4 bolts for the "e3d v6 compact extruder for i3 rework":
http://www.thingiverse.com/thing:725082
thingiverse
free
Dual Melzi Box for RepRapPro Tricolor Mendel by GiulianoM
...clips on the top piece snapped off really easily, so i modified the top to make the clip walls a little thicker (2.0mm vs 1.5mm).
Lm8Luu
thingiverse
free
X-Carriage for LM8LUU by Huang_yung
...x-carriage for lm8luu by huang_yung
thingiverse
x-carriage for lm8luu
thingiverse
free
lm8luu by ngandalf
...lm8luu by ngandalf
thingiverse
lm8uu for geetech prusa i3 pro b
thingiverse
free
lm8luu printable bearing by laughingman
...lm8luu printable bearing by laughingman
thingiverse
// lm8luu
lm8uu_od = 15;
lm8uu_length = 45;
lm8uu_id = 8.1;
thingiverse
free
Lm8luu casing by Toroddandre
...aring.
edit: new picture of lm8luu casing
i recommend using brim on this if printed standing up.. my first test got knocked of :)
thingiverse
free
LM8LUU bearing clip by dspirov
...or the lm8luu and made the back a little thinner.
see this page for standard bearing sizes: http://reprap.org/wiki/linear_bearing
thingiverse
free
Prusa MK2 x carriage LM8LUU by stefanino
...prusa mk2 x carriage lm8luu by stefanino
thingiverse
prusa mk2 x carriage with lm8luu bearings
thingiverse
free
LM8LUU by PulseNeko
... and you didnt want to play around with trying to get the right scaling percentage.
these are designed to work with m4 fasteners.
thingiverse
free
LM8LUU Packer for super lube grease by PigeonPrint
...r super lube grease by pigeonprint
thingiverse
modified to fit the super lube grease threads a little better and fit the lm8luu.
thingiverse
free
LM8UU LM8LUU linear bearings bed holder by CyfroN
...lm8uu lm8luu linear bearings bed holder by cyfron
thingiverse
lm8uu lm8luu linear bearings bed holder
thingiverse
free
LM8LUU Bearing Mount by walter
...part. designed to fit the rigidbot z-axis bearings.
printer:
-- rigidbot
filaments:
-- colorfabb black pla/pha
*affiliate link
Rework
3d_export
$25
riva aquarama 1970
...visualization, as well as, if desired, it can be reworkd for 3d printing. in the near future, a model...
3d_export
$8
Mosaic 1 3D Model
...outdoor indoor vector ceramic glass mosaic decorative mosaic manually reworkd into a vector. the image is then modified in...
3d_export
$65
sci-fi scene for rendering restyling - tesla
...colors with the name, metal, light metal, dark metal, reworkd renders for preview and processed in photoshop using a...
3d_export
$22
a filter assembly and inspection line
...laser marking station (op40), one packaging station (op50), one rework and pump water detection station (op60), and two assembly...
3d_export
$19
muuto raw chair
...the muuto raw chair.<br>raw chair is a striking functional reworkng of a recognizable everyday object. a part of the...
3d_export
$12
desert rocks stock in blender
...in obj format (non-textured), together with the textures, for reworkng them in other programs.<br>notes: the scene include 12 simple...
3d_export
$10
arclinea principia
...the essence, with the basic principles of the kitchen, reworkd: new steel technology and natural wood cutting. the extraordinary...
thingiverse
free
Doughnut Rework by Johhnny
...doughnut rework by johhnny
thingiverse
i reworked tzani's mobius doughnut for dual extrusion.
thingiverse
free
Beanie the Transformer rework by Whirl55
...beanie the transformer rework by whirl55
thingiverse
found and reworked head pin
and all files
thingiverse
free
AM10 - am8 rework Y
...am10 - am8 rework y
thingiverse
totaly rework to turn your am8 into an am10 with only 2 pieces
Carriage
archibase_planet
free
Carriage
...arriage
archibase planet
perambulator baby carriage pram
carriage n250908 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
free
carriage
...carriage
3dexport
old fashion carriage model, more files here:
turbosquid
$140
Carriage
...urbosquid
royalty free 3d model carriage for download as max on turbosquid: 3d models for games, architecture, videos. (1482052)
turbosquid
$25
Carriage
...urbosquid
royalty free 3d model carriage for download as max on turbosquid: 3d models for games, architecture, videos. (1285944)
3d_export
free
carriage
...carriage
3dexport
game cart
3d_ocean
$15
Barrel Carriage
...ieval oak old transport wheels wine wood
this model contains a barrel and a carriage. it is a medieval type of wood oak carriage.
turbosquid
$40
Carriage
...ty free 3d model carriage for download as obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1290094)
turbosquid
free
Carriage
...yalty free 3d model carriage for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1239157)
3d_export
$5
Medieval carriage
...medieval carriage
3dexport
medieval carriage in fairy style
turbosquid
$58
Carriage
...d model carriage with scene for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1276262)
Prusa
turbosquid
$2
Frame Filament Guide Clip-On for Prusa Mk3
...rame filament guide clip-on for prusa mk3 for download as stl on turbosquid: 3d models for games, architecture, videos. (1634730)
3d_export
free
prusa i3 mk3s laser mount for opt lasers
...to learn more about the blue laser technology that conceived the cutting and engraving laser heads from opt lasers, please visit:
turbosquid
free
Prusa small printer adapter holder
...er for download as ipt, skp, dwg, dxf, fbx, ige, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1642936)
3d_export
$30
geisha by jonathan adler
...** i did a 3d printing test in the prusa software, you can find it among the attached images.<br>exchange:<br>.blend...
thingiverse
free
Prusa without Prusa (rc2) by madless
...prusa without prusa (rc2) by madless
thingiverse
just the main part of prusa rc2 faceshield, without writing.
enjoy :)
thingiverse
free
Prusa by acejbc
...prusa by acejbc
thingiverse
prusa knob info
m3 8mm screw
thingiverse
free
Prusa house
...prusa house
thingiverse
how prusa house could look like...
thingiverse
free
Prusa Mk2 "Fake Prusa" LCD cover by anraf1001
...r by anraf1001
thingiverse
version of prusa's lcd cover with "fake prusa" instead of "original prusa"
thingiverse
free
Prusa stabilizator by gutiueugen
...prusa stabilizator by gutiueugen
thingiverse
prusa stabilizator
thingiverse
free
Keychain Prusa by rbarbalho
...keychain prusa by rbarbalho
thingiverse
keychain with text prusa.