Thingiverse
Prop Balancer by Powerman3d
by Thingiverse
Last crawled date: 2 years, 10 months ago
Designed this prop balancer to work with the Great Planes finger balancer, or any other finger balancer that has a rod 55.34mm wide.
To account for tolerances, the balancer was designed with two vertical risers spaced 56mm apart. This way if the magnets are not completely flush, the finger spacer will still be able to move freely. The balancer will accommodate props up to 11" in diameter for full rotation; you can use larger propellers but they will not rotate fully.
Printing:
Recommend changing the wall count from 2 to 4. This will ensure the vertical risers do not flex. I believe in Cura if you change the wall thickness to 1.6mm, ,this will automatically change the wall count to 4 as the wall count is calculated based on the nozzle size of 0.4mm (1.6mm wall thickness / 0.4 Nozzle = wall count of 4). In Simplify3D the wall count can be changed in the Layers tab>Outline/Perimeter Shells
Infill is 15%. I printed using PLA+ at 220C so the layer adhesion was very good.
You should be able to use regular PLA.
The magnets are rare earth magnets 8mm in diameter and 3mm thick. The balancer was designed such that the magnets press fit snugly without CA. I used a flat ruler and pushed them in. Note do not force them in with excessive pressure as it could crack the part. if the hole is too tight, just take an Exacto knife and remove a bit of material from the top of the hole. Print with NO Supports
To account for tolerances, the balancer was designed with two vertical risers spaced 56mm apart. This way if the magnets are not completely flush, the finger spacer will still be able to move freely. The balancer will accommodate props up to 11" in diameter for full rotation; you can use larger propellers but they will not rotate fully.
Printing:
Recommend changing the wall count from 2 to 4. This will ensure the vertical risers do not flex. I believe in Cura if you change the wall thickness to 1.6mm, ,this will automatically change the wall count to 4 as the wall count is calculated based on the nozzle size of 0.4mm (1.6mm wall thickness / 0.4 Nozzle = wall count of 4). In Simplify3D the wall count can be changed in the Layers tab>Outline/Perimeter Shells
Infill is 15%. I printed using PLA+ at 220C so the layer adhesion was very good.
You should be able to use regular PLA.
The magnets are rare earth magnets 8mm in diameter and 3mm thick. The balancer was designed such that the magnets press fit snugly without CA. I used a flat ruler and pushed them in. Note do not force them in with excessive pressure as it could crack the part. if the hole is too tight, just take an Exacto knife and remove a bit of material from the top of the hole. Print with NO Supports
Similar models
thingiverse
free
Key Hanger Holder by Powerman3d
... shells
infill is 20%. i printed using pla+ at 225c so the layer adhesion was very good.
you should be able to use regular pla.
thingiverse
free
Magnetic Prop Balancer by thattolleyguy
...magnet based prop balancer.
the magnets i used were 2.75mm thick by 29.5mm in diameter.
you also need a fingertip prop balancer.
thingiverse
free
Poly Planter for Succulants
...s planted was made with 1.6mm thick walls for 0.4mm nozzle.. thus 5 layers thick.
i will update with pics when i have printed it.
thingiverse
free
0.4 Nozzle Wall Thickness Calibrator by AcrimoniousMirth
...and engineering strength parts. your slicer may turn it into 1.5 or 1.6 depending on the algorithms and its useful to know which!
thingiverse
free
Spur Gear Vase by forrestflux
... thickness: 1.6mm is adequate wall and bottom thickness, 0% infill and 0 top layers
if you have any questions, please let me know
thingiverse
free
Fridge Magnet by kobus910
...uot; thick, i dropped it in the hole a couple layers before the covering layer.
prints at any layer thickness, i used 20% infill.
thingiverse
free
DIY Simulation Pedals by Spitintomyjar
...them to a proper position
here is a video of pedals in turkish feel free to ask any related questionshttps://youtu.be/cjuac0l4sj4
thingiverse
free
Mad Catz RAT 5 Finger Rest by Malte92
...t 0.1mm
infill 50%
it took 54min to print
all walls are 2mm thick so it's easy to reheat and adjust to the fingers if desired
thingiverse
free
Survive Escape from Atlantis - component boxes by glitch17
...glued them in and they are staying in. the tops of the boxes you will need to rotate 180 degrees to they print with the top down.
thingiverse
free
filament holder by blackd74
...lament diameter - 1.75mm
nozzle diameter - 0.4mm
i print it and test it... it can hold up to 6.5 kilo!!! in 6.5 kilo its broke!
Powerman3D
thingiverse
free
Tesla Keychain by Powerman3d
...tesla keychain by powerman3d
thingiverse
printed at 200c, no supports.
two sizes. 100% and 80%. the 80% is about 43mm tall.
thingiverse
free
Desktop Organizer by Powerman3d
...is a remix of https://www.thingiverse.com/thing:4696810 ; but was created from scratch.
i needed a version with more compartments
thingiverse
free
Bench test 9g servo holder by Powerman3d
... it easier to tell servo direction.
i oversized the holder a bit to account for variances in the size of 9g servos on the market.
thingiverse
free
LED Strip Remote Holder by Powerman3d
...ted this in fusion 360 so feel free to change the dimensions if that suites you.
i printed the parts vertically without supports.
thingiverse
free
Mini solar panel mount by Powerman3d
...pport to be removed easily
this design was inspired by pavel riedl https://www.prusaprinters.org/prints/12320-solar-panel-holder
thingiverse
free
Key Hanger Holder by Powerman3d
... shells
infill is 20%. i printed using pla+ at 225c so the layer adhesion was very good.
you should be able to use regular pla.
thingiverse
free
Turnigy 130A Precision watt meter replacement housing by Powerman3d
...ing surfaces of each half of the case using 150grit sandpaper placed on a flat surface. i did this and the seam is now invisible.
Balancer
3ddd
$1
balance
...balance
3ddd
balance
design_connected
$11
Balance
...balance
designconnected
vibia balance computer generated 3d model. designed by vilardell, jordi.
3ddd
$1
Windfall | Balance
...windfall | balance
3ddd
balance , windfall
люстра windfall balance
3d_export
$5
balance
...balance
3dexport
3ddd
free
Vibia balance
... vibia , balance
vibia balancehttp://www.vibia.com/en
3ddd
$1
Vibia Balance
...vibia balance
3ddd
vibia
vibia balance
turbosquid
$40
balance
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Balance
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Balance
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$8
Balance
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Prop
3ddd
$1
Props
...props
3ddd
props
3d_ocean
$10
Props
...ject you need this props design this 6 taype for props to get your design perfect and nice file include : 1 max 2 obj 3 3ds 4 zip
turbosquid
$15
Props
...s
turbosquid
royalty free 3d model props for download as max on turbosquid: 3d models for games, architecture, videos. (1249032)
turbosquid
$1
PROPS
...d model props for download as unitypackage, obj, fbx, and tga on turbosquid: 3d models for games, architecture, videos. (1627660)
turbosquid
$5
props
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
PROP
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
kids props
...kids props
3ddd
декоративный набор
kids props
3d_ocean
$8
Street props
...l barrier prop roads street street prop
street props game models barrel barrier roads aircos jerrycan models fbx obj and max file
turbosquid
$39
Apocalyptic Props
...uid
royalty free 3d model apocalyptic props for download as on turbosquid: 3d models for games, architecture, videos. (1380028)
turbosquid
$1
Bunker props
...rbosquid
royalty free 3d model bunker props for download as on turbosquid: 3d models for games, architecture, videos. (1196014)