GrabCAD
Pressure Sensor SPC01B1A
by GrabCAD
Last crawled date: 1 year, 11 months ago
Enclosure:
The assemble printed circuits fits in a small two pieces enclosure with snap latches. Overall dimensions are with the connector: length 25,6mm x wide 8,0mm x height 17,0mm.
Circuit Design:
Pressure sensor is a piezo resistive element. Very small size and low power consumption and temperature influence. Pressure range is from 0..37kPa . Also available with a range of -50 to 50kPa.
Sensor is connected to a integrated analog sensor signal conditioner. This device provides amplification, calibration, and temperature compensation to enable an overall performance approaching the inherent repeatability of the sensor. The signal path is fully analog while it is digitally controlled. The trimming of the offset and span are calibrated digitally with integrated 16-bit DACs. Advantage are no external components required for trimming. Therefore a low count components and simple printed circuit design.
Signal conditioner IC’s also provides overvoltage Protection to 45V and Reverse-Voltage Protection to 45V. Sensor fault detection. The signal conditioner provides a high-performance ratiometric output that is proportional to the power-supply voltage. Circuit also includes 3 test pins for during production testing, trimming and calibration in a test jig. The analog output pin functions also as a digital in- and output serial interface. Used for a one wire asynchronous serial data communications between the device and a host calibration test system. Hole device power supply is 5V, +/-4mA.
Electronic assembly:
All components are from surface mount type, so that they can be placed automatically by a pick and place machine. For this purpose the printed circuit board is also panelized in a configuration of 5x10 devices, a total of 50 device per panel. Therefore better and easier to handle during production en testing. This is also the reason for the holes in the sides of the panel. These are for alignment purposes during differed stages in the production. Panel is provide with strategy placed milling and V-curves. To facilitate easier separation each sensor devices from the panel. Before separations the panel format can be used in a test jig for testing, trimming and calibration. Holes in the side of the panel can be used for alignment in de test jig. So that the test point on the bottom of the printed circuit board line up with de test pins on the jig. By these pins the totally analog output devices can be digitally trimmed, calibrated and tested.
The assemble printed circuits fits in a small two pieces enclosure with snap latches. Overall dimensions are with the connector: length 25,6mm x wide 8,0mm x height 17,0mm.
Circuit Design:
Pressure sensor is a piezo resistive element. Very small size and low power consumption and temperature influence. Pressure range is from 0..37kPa . Also available with a range of -50 to 50kPa.
Sensor is connected to a integrated analog sensor signal conditioner. This device provides amplification, calibration, and temperature compensation to enable an overall performance approaching the inherent repeatability of the sensor. The signal path is fully analog while it is digitally controlled. The trimming of the offset and span are calibrated digitally with integrated 16-bit DACs. Advantage are no external components required for trimming. Therefore a low count components and simple printed circuit design.
Signal conditioner IC’s also provides overvoltage Protection to 45V and Reverse-Voltage Protection to 45V. Sensor fault detection. The signal conditioner provides a high-performance ratiometric output that is proportional to the power-supply voltage. Circuit also includes 3 test pins for during production testing, trimming and calibration in a test jig. The analog output pin functions also as a digital in- and output serial interface. Used for a one wire asynchronous serial data communications between the device and a host calibration test system. Hole device power supply is 5V, +/-4mA.
Electronic assembly:
All components are from surface mount type, so that they can be placed automatically by a pick and place machine. For this purpose the printed circuit board is also panelized in a configuration of 5x10 devices, a total of 50 device per panel. Therefore better and easier to handle during production en testing. This is also the reason for the holes in the sides of the panel. These are for alignment purposes during differed stages in the production. Panel is provide with strategy placed milling and V-curves. To facilitate easier separation each sensor devices from the panel. Before separations the panel format can be used in a test jig for testing, trimming and calibration. Holes in the side of the panel can be used for alignment in de test jig. So that the test point on the bottom of the printed circuit board line up with de test pins on the jig. By these pins the totally analog output devices can be digitally trimmed, calibrated and tested.
Similar models
grabcad
free
Hardware Design of Analog and Digital TestBed
...al through switches and leds. rs485 to uart and smps voltage regulator 24v to 12v, 5v, 3.3v and adjustable voltage 0v to 17.667v.
3dwarehouse
free
Toradex Oak Usb sensor - Pressure
...p mode, allows using the device not only in fixed installations, but also in mobile applications. #pressure #sensor #toradex #usb
grabcad
free
Pressure Sensor SPC01B2A
...ment, but also a part of the enclosure.
starting point small and compact, w 16mm x l 20mm x h 11mm.
one part for the enclosure.
3dwarehouse
free
Fast response stepped-wave switching power converter circuit
...ge is outside the control band limits. an application is a fast response switching power amplifier for driving sonar transducers.
thingiverse
free
Input adapter for filament sensor by flipper
...o inaccurate output.
this is not needed for a general purpose analog input because the current draw is very low for these inputs.
thingiverse
free
DIY Energy consumption counter for power meters by m1n1m
...can all be done on a arduino or something similar also. the stl file provided fits the sensor and...
grabcad
free
Compression jig
...press round objects.
the digital gauge and pressure sensor are attached to check the press force and the length of the pressure.
grabcad
free
Scroff Case with PCB & E3D Connector
...the digital signal to analog to drive an earphone or loudspeaker amplifier in order to produce sound (analog air pressure waves).
thingiverse
free
D1M BLOCK - 2xAMUX (custom) by IOT123
...rip are required for this build.
video (slight sync issue with the serial console overlay).
instructions
code examples
d1m blocks
3dwarehouse
free
FRC Analog Pressure Sensor
...ure sensor. check out the collection below for other frc parts! enjoy. #analog #digital #first_robotics #frc #pneumatic #robotics
Pressure
3d_export
$5
pressure gauge
...pressure gauge
3dexport
pressure gauge
3d_export
$40
Pressure Vessel
...pressure vessel
3dexport
pressure vessel assembly render 3d modelling design
3d_export
$5
Pressure cooker
...pressure cooker
3dexport
simple low-poly pressure cooker model. not removable parts.
3d_export
$5
protected pressure gauge
...protected pressure gauge
3dexport
protected pressure gauge
turbosquid
$25
Vintage US Gauge Co Cluster, Pressure, Oil Pressure & Vacuum Fuel Pressure
...re for download as 3ds, dxf, obj, c4d, fbx, 3dm, dwg, and stl on turbosquid: 3d models for games, architecture, videos. (1367117)
turbosquid
$20
PRESSURIZATION FAN
...
royalty free 3d model pressurization fan for download as max on turbosquid: 3d models for games, architecture, videos. (1269534)
turbosquid
$20
Pressurization Pumps
...oyalty free 3d model pressurization pumps for download as max on turbosquid: 3d models for games, architecture, videos. (1270559)
turbosquid
$23
Pressure cooker
...ee 3d model pressure cooker for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1440991)
turbosquid
$25
pressure cooker
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$3
Pressure Controller
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Sensor
3d_export
free
parking sensor
...parking sensor
3dexport
car parking sensor
turbosquid
$1
Sensor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Smoke sensor
...port
smoke sensor, can be an impressive element for your projects. easy to use, realistic image, low polygon, quality materials.
3d_export
$5
Air Quality Sensor v1
...air quality sensor v1
3dexport
air quality sensor v1
3d_export
$15
float sensor
...e up render. - all parts and materials are logically named. other formats ================= - collada (.dae) - autodesk fbx - obj
turbosquid
$26
Wind sensor C
...free 3d model wind sensor c for download as 3ds, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1328943)
turbosquid
$26
Wind sensor B
...free 3d model wind sensor b for download as 3ds, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1328168)
3d_export
$5
ultrasound sensor
...ivers convert ultrasound into electrical signals, and transceivers can both transmit and receive ultrasound. export in: -obj -fbx
3ddd
free
Вытяжка Shindo pallada sensor
... вытяжка
вытяжка shindo pallada sensor. в двух размерах - 600 и 900. текстуры в комплекте.
turbosquid
$52
Wind sensor A B C
...
royalty free 3d model wind sensor a b c for download as fbx on turbosquid: 3d models for games, architecture, videos. (1408406)