Thingiverse
Precision Piezo 20mm disc to LM8UU bearing mount by SupraGuy
by Thingiverse
Last crawled date: 3 years ago
Edit 8/13/2018:
So... I actually built and tested this. I deprecated the long version, as the small one is plenty strong enough, and has more than enough advantages to decide not to need the long version.
A couple of problems that I've addressed in the new version:
Using the 4 screws to hold the whole assembly together puts the stress of holding the bearings on the piezo disc. If your printer didn't make this exactly to dimensions, or if your LM8UU bearings were slightly larger than spec, this results in a lack of sensitivity. It can still be tuned, but I'm not sure about longevity of the setup that way, and I don't want to introduce any slop in the bed mount. Solution: Make 2 of the holes in the plunger piece larger, to allow the socket head cap screws to float. These can be tightened to keep cap pressure on the bearings, while the other 2 hold the entire assembly together. This is only possible on the small version and was the major deciding factor for deprecating the large version.
Using 2 screws to mount the assembly to the bed was excessive, and not necessary. A single screw at leach location is more than adequate to prevent lateral motion of the bed particularly if it is mounted tightly, as intended. A single screw CAN also allow a spring tension height adjustment for levelling, though I am not certain what this will do to sensitivity. (PIezo discs are very sensitive, so this might still work, but result in more possible false triggers.) Solution: move the mount screw to the center of the plunger. Certainly you could opt to just use one of the 2 screw locations from before, though this would be unbalanced if you were to opt for the spring mount.
It was possible to mount the system so that the disc was already at the allowed maximum motion. This is a combination of factors, including the first issue addressed by making the 2 screws float. I increased the depth of the opening, to allow for more flex in the piezo disc, and increased the height of the plunger by 0.25mm. This should not damage the pieze ceramic in the event that the plunger is pressed fully to the disc mount cup, but does allow for a little more adjustment range.
Original description follows:
Mounting system for heated bed. you will need 3 of these (Though I see no reason you couldn't use 4, you should only need 3)
2 versions included, one is 30mmX50mm, the other is 30mmX30mm. This might be a little weaker, as the screw holes are closer to the actual bearing opening, but will save a little space.
Each set holds one 20mm piezo disc sensor. A plunger piece is mounted to your bed via 2 screws spaced at 40mm. The plunger piece should hold 2 standard 3mm nuts (5.5mm wrench size) Each set has 4 pieces. An upper and lower "cap" piece to hold the LM8UU bearing. The lower cap will hold 4 3mm nuts. A bed to hold the 20mm piezo disc goes on the upper cap, and then the plunger should take a set of 3mm screws into it. The whole assembly will then have the disc and the LM8UU bearing sandwiched into it and have a slight pre-tension applied via the 4 screw/nut combinations holding it together.
The mounting deck should be between 21.5 and 22.5mm from the centre point of the LM8UU bearing, with some slight allowance for the piezo disc itself. I set up my drive axis to assume 22mm between mounting deck and rod centres.
The upside to this is that automatic bed leveling should be easy as pie. The downside is that this leaves practically nothing for making adjustments. The piezo disc itself is some 9mm away from the bed material. This along with whatever mounting strata should insulate it from the heated bed adequately for function.
This is a work in progress. I'm publishing this here as an addemdum to my beltless printer design, since I had to redesign the bed mechanism anyway, and I want to implement the Precicion Piezo sensors anyway, it seemed like a good idea.
So... I actually built and tested this. I deprecated the long version, as the small one is plenty strong enough, and has more than enough advantages to decide not to need the long version.
A couple of problems that I've addressed in the new version:
Using the 4 screws to hold the whole assembly together puts the stress of holding the bearings on the piezo disc. If your printer didn't make this exactly to dimensions, or if your LM8UU bearings were slightly larger than spec, this results in a lack of sensitivity. It can still be tuned, but I'm not sure about longevity of the setup that way, and I don't want to introduce any slop in the bed mount. Solution: Make 2 of the holes in the plunger piece larger, to allow the socket head cap screws to float. These can be tightened to keep cap pressure on the bearings, while the other 2 hold the entire assembly together. This is only possible on the small version and was the major deciding factor for deprecating the large version.
Using 2 screws to mount the assembly to the bed was excessive, and not necessary. A single screw at leach location is more than adequate to prevent lateral motion of the bed particularly if it is mounted tightly, as intended. A single screw CAN also allow a spring tension height adjustment for levelling, though I am not certain what this will do to sensitivity. (PIezo discs are very sensitive, so this might still work, but result in more possible false triggers.) Solution: move the mount screw to the center of the plunger. Certainly you could opt to just use one of the 2 screw locations from before, though this would be unbalanced if you were to opt for the spring mount.
It was possible to mount the system so that the disc was already at the allowed maximum motion. This is a combination of factors, including the first issue addressed by making the 2 screws float. I increased the depth of the opening, to allow for more flex in the piezo disc, and increased the height of the plunger by 0.25mm. This should not damage the pieze ceramic in the event that the plunger is pressed fully to the disc mount cup, but does allow for a little more adjustment range.
Original description follows:
Mounting system for heated bed. you will need 3 of these (Though I see no reason you couldn't use 4, you should only need 3)
2 versions included, one is 30mmX50mm, the other is 30mmX30mm. This might be a little weaker, as the screw holes are closer to the actual bearing opening, but will save a little space.
Each set holds one 20mm piezo disc sensor. A plunger piece is mounted to your bed via 2 screws spaced at 40mm. The plunger piece should hold 2 standard 3mm nuts (5.5mm wrench size) Each set has 4 pieces. An upper and lower "cap" piece to hold the LM8UU bearing. The lower cap will hold 4 3mm nuts. A bed to hold the 20mm piezo disc goes on the upper cap, and then the plunger should take a set of 3mm screws into it. The whole assembly will then have the disc and the LM8UU bearing sandwiched into it and have a slight pre-tension applied via the 4 screw/nut combinations holding it together.
The mounting deck should be between 21.5 and 22.5mm from the centre point of the LM8UU bearing, with some slight allowance for the piezo disc itself. I set up my drive axis to assume 22mm between mounting deck and rod centres.
The upside to this is that automatic bed leveling should be easy as pie. The downside is that this leaves practically nothing for making adjustments. The piezo disc itself is some 9mm away from the bed material. This along with whatever mounting strata should insulate it from the heated bed adequately for function.
This is a work in progress. I'm publishing this here as an addemdum to my beltless printer design, since I had to redesign the bed mechanism anyway, and I want to implement the Precicion Piezo sensors anyway, it seemed like a good idea.
Similar models
thingiverse
free
20mm Precisions Piezo underbed mounts by SupraGuy
...small amount of movement that the sensor should require. there are 2 slots for the sensor wires, though you should only need one.
thingiverse
free
Reduced Binding Y bearing Block for Zaribo & Haribo by ocieward
...ular one suited to the zaribo and haribo. fyi, the two mounting screws are spaced 20mm apart.
video: https://youtu.be/nvczhgm9ipk
thingiverse
free
Underbed Piezo Mounts by RandomFactoid
...and 3 base/top layers from petg. i would probably want to avoid using pla if using a heated bed, although it might still work ok.
thingiverse
free
Beefy Y Axis screw and nut bed mount for LM8UU by engineglue
...from scratch, these y axis bed mounts secure to lm8uu bearings with a 3mm screw and nut instead of zip ties. plus they are beefy!
thingiverse
free
LM8UU bearing holder by Wired1
...into your carriage design.
20 september - added a one-screw version, identical except only one machine screw to secure the lm8uu.
thingiverse
free
(Beta) Piezo UnderBed Mounts by Precision Piezo by DjDemonD
...sulation to the mounts to keep heat from the bed away from the piezos.
future release might include some clamps on the top parts.
thingiverse
free
LM8UU Bearing Holder by walter
...e for a m5 screw (which i use to trigger the z-limit switch).
the holes are placed 1.25 inches apart, and sized for a m3 screw.
thingiverse
free
Hypercube Evolution - HEVO Fusion RC - Piezo 27mm Mount by otaku521
...ps://www.tinkercad.com/things/kc8tdyrguhe-hevo-sml-27mm-piezo-plate/editv2?sharecode=_77z-n0nrz_aszmqffpru-tr07xbymg-yhdvkch_oqq=
thingiverse
free
Saw jig for 3mm rod by ledeev001
...ut 3mm carbon rod with a hacksaw.
use 3.5mm x 20mm(+) countersunk screws to hold it to a bench or piece of wood to allow cutting.
thingiverse
free
Low-profile print bed LM8UU holder by kedibekar3D
... just clear an sk8 holding the linear rails. no zip-ties required!
edit 03/04/2018: added version that can hold 2 lm8uu bearings.
Supraguy
thingiverse
free
Rounded version of thing 619672 -- 20 sided die shift knob (5 speed) by SupraGuy
...ners rounded (not too comfortable on the hands when pointy) and added a 1.25mm thread to the inside for mounting to most toyotas.
thingiverse
free
ESP32 Camera Case by SupraGuy
...2 camera pieces that i have. the overall fit is far superior now, and using a 2 pin dupont connector for power works well for me.
thingiverse
free
20mm Precisions Piezo underbed mounts by SupraGuy
...small amount of movement that the sensor should require. there are 2 slots for the sensor wires, though you should only need one.
thingiverse
free
Spectre Pro 23030 Fan grille with Imperial Cog by SupraGuy
...in mounting to your case.
the third file is a plain grille, with the hexagonal pattern covering the entire area of the fan blade.
thingiverse
free
RAMPS 1.4 case with mount for 80mm fan by SupraGuy
... the holes for the screws after all, as drilling out the tiny holes is annoying. motherboard mounting screws should work perfect.
thingiverse
free
Mks GEN L v1.0 case w/ 5015 cooling fan by SupraGuy
... and hot air exhaust. an additional exit is present for ribbon cables connecting a reprap discount controller on the curved side.
thingiverse
free
T8 Leadscrew Driven I3 Printer modification by SupraGuy
...is, so this should be regarded as beta, if not alpha. i believe that this is ready to try at least, and i intend to use it as-is.
Piezo
turbosquid
$5
Buzzer Piezo
...odel buzzer piezo for download as max, max, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1607700)
3d_export
$7
buzzer piezo
...;all materials are logically named<br>the main format is in 3ds max 2013.<br>satisfaction guarranteed<br>thanks
3d_export
$15
Buzzer 3D Model
...audio electronic component signalling piezoelectric disk alarm timer electric piezo industrial part electrical bell doorbell buzzer 3d model download...
thingiverse
free
Hypercube_evolution E3D_Titan_Aero with piezo
...ercube_evolution e3d_titan_aero with piezo
thingiverse
hypercube_evolution a piezo z-axis sensor was attached to e3d_titan_aero.
thingiverse
free
Precision-Piezo Probe with 3 Piezo 15mm by Tech-Raton
...if bigger, you'll lose the piezo marks)
you just have to slide the part between the heatsink and the effector (or your mount)
thingiverse
free
Piezo Chimera mount by RKS7204
...piezo chimera mount by rks7204
thingiverse
mount for e3d chimera hotend and piezo sensor
thingiverse
free
Piezo v1.22 Mount by Suggy
...piezo v1.22 mount by suggy
thingiverse
mount for under bed piezo censor pcb
thingiverse
free
Precision Piezo - 27mm and 20mm Piezo Disc drill guide. by DjDemonD
... djdemond
thingiverse
drilling guide for piezo discs to centre your drill.
see youtube video here: https://youtu.be/ms1fd0v5z68
thingiverse
free
Underbed Piezo Mounts by fcollingwood
...the piezos are smooth. two of the arms a required and two of the mirror arms are required
everything else can be printed at 0.2mm
thingiverse
free
(Beta) Piezo UnderBed Mounts by Precision Piezo by DjDemonD
...sulation to the mounts to keep heat from the bed away from the piezos.
future release might include some clamps on the top parts.
Lm8Uu
thingiverse
free
Lm8uu Bearing
...lm8uu bearing
thingiverse
lm8uu bearing
thingiverse
free
2020 lm8uu
...2020 lm8uu
thingiverse
lm8uu 2020 bosch
thingiverse
free
LM8UU spiral & LM8UU linear by Dmawzx
...lm8uu spiral & lm8uu linear by dmawzx
thingiverse
replace lm8uu linear ball bearing type.
size: 8x15x24 mm
thingiverse
free
LM8UU by Emyx74
...lm8uu by emyx74
thingiverse
printable linear beating lm8uu
thingiverse
free
lm8uu holder
...lm8uu holder
thingiverse
simple holder for lm8uu
screw hole distance is 38mm
thingiverse
free
Printed LM8UU by peke
...printed lm8uu by peke
thingiverse
a spare lm8uu
thingiverse
free
LM8UU holder by Modellaner
...lm8uu holder by modellaner
thingiverse
another lm8uu holder.
thingiverse
free
Adapter LM12UU to LM8UU
...adapter lm12uu to lm8uu
thingiverse
adapter lm12uu to lm8uu
thingiverse
free
lm8uu holder by yusuf_uzun
...lm8uu holder by yusuf_uzun
thingiverse
lm8uu holder for 3d printer
thingiverse
free
LM8UU Small by haldemir55
...lm8uu small by haldemir55
thingiverse
small size lm8uu support
Disc
archibase_planet
free
Discs
...discs
archibase planet
compact discs cd compact disk
discs - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$7
SS with Disc Bonbon with disc
...ee 3d model ss with disc bonbon with disc for download as max on turbosquid: 3d models for games, architecture, videos. (1285181)
3d_export
$20
Car discs
...car discs
3dexport
car discs
3d_export
$5
disc knob
...disc knob
3dexport
disc knob
3d_export
$5
disc knob
...disc knob
3dexport
disc knob
3d_ocean
$2
Compact Disc
...compact disc
3docean
album audio cd compact disc dvd laser disc movie music
a cd
turbosquid
$30
Protrusion and slipped disc herniated disc
...usion and slipped disc (herniated disc) for download as blend on turbosquid: 3d models for games, architecture, videos. (1572177)
turbosquid
free
disc
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$5
Realistic Floppy Disc
...op storage usb
this is a model of a floppy disc. floppy discs were used as computer storage devices before the invention of usbs.
3d_export
$10
brake-disc-brembo
...brake-disc-brembo
3dexport
brake-disc-brembo
20Mm
3d_export
$20
german 20mm flak
...german 20mm flak
3dexport
german 20mm flak
turbosquid
$58
M-75 20mm AA
...squid
royalty free 3d model m-75 20mm aa for download as obj on turbosquid: 3d models for games, architecture, videos. (1174302)
turbosquid
$5
Drill Bit Set 6mm to 20mm
...ill bit set 6mm to 20mm for download as stl, sldpr, and sldas on turbosquid: 3d models for games, architecture, videos. (1257104)
turbosquid
free
Oerlikon 20mm anti-aircraft gun
...mm anti-aircraft gun for download as lwo, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1430549)
turbosquid
free
20mm Flak 38 Flakveirling (Simple)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$7
Ammo Box WWII US Military 20mm MK3
...mmo box wwii us military 20mm mk3 for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1360607)
cg_studio
$35
German 20mm MG151/20 Sprgr cartridge with cutaway3d model
...j - german 20mm mg151/20 sprgr cartridge with cutaway 3d model, royalty free license available, instant download after purchase.
cg_studio
$35
German 20mm MG151/20 Pzgr cartridge with cutaway3d model
...obj - german 20mm mg151/20 pzgr cartridge with cutaway 3d model, royalty free license available, instant download after purchase.
3d_export
$35
German 20mm MG15120 cartridge with cutaway 3D Model
...ammunition munition granate panzer airforce luftwaffe
german 20mm mg15120 cartridge with cutaway 3d model emeral_d 21635 3dexport
3d_export
$35
German 20mm MG 15120 cartridge with cutaway 3D Model
...mmunition munition granate panzer airforce luftwaffe
german 20mm mg 15120 cartridge with cutaway 3d model emeral_d 21633 3dexport
Precision
turbosquid
$40
Precision Screwdriver
...model precision screwdriver for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1301545)
cg_studio
$59
Precision mountain3d model
...n mountain3d model
cgstudio
.max - precision mountain 3d model, royalty free license available, instant download after purchase.
turbosquid
$10
Lazer Precision rifle
...lty free 3d model lazer precision rifle for download as blend on turbosquid: 3d models for games, architecture, videos. (1313439)
3d_export
$7
Precision Indicator
...includes all scene, lighting, cameras, materials and textures. many file formats are available. the visuals are in 4k resolution.
turbosquid
$59
Dell Precision 7510 Laptop
... dell precision 7510 laptop for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1678133)
turbosquid
$45
11 Precision Metals Bldg03
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$37
Kelly Wearstler Precision bench
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$18
Kelly Wearstler Precision table
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$60
Fender Precision Bass 3D Model
...uitar frets instrument electric bassguitar 4string rock blues pop music
fender precision bass 3d model rendersteel 86834 3dexport
3d_export
$5
precision centrifugal pump
...ceed 180℃ and the inlet pressure does not exceed 0.8mpa.<br>drawings can only be used as a reference for mechanical design!
Bearing
3d_export
$6
Bear
...bear
3dexport
bear
3d_export
$5
bearing
...bearing
3dexport
bearing
3d_export
$12
bear
...bear
3dexport
bear for 3d printing toy
3d_ocean
$9
Bearing
...ne ball ballbea bearing bearings engine hard industrial machine mechanic metal part piece plastic ring screw sphere steel
bearing
archibase_planet
free
Bear
...bear
archibase planet
statuette bear picturesque element
bear - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
bear
...bear
3dexport
bear have a stl.,3dm files
archibase_planet
free
Bear
...bear
archibase planet
bear animals omnivorous animal
bear angry n250907- 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Bear
...bear
archibase planet
bear animals omnivorous animal
bear easy n250907 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3ddd
$1
Teddy bear
...teddy bear
3ddd
teddy bear , медведь
teddy bear :)
3d_ocean
$12
Bear
... formats. created with 3d max 9.0. this file is very useful for learning & rigging. it can be used for any professional work.
Mount
3d_export
free
mounting bracket
...mounting plate is the portion of a hinge that attaches to the wood. mounting plates can be used indoors, cabinetry and furniture.
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)