Thingiverse
PopKeep by ThatDrewLion
by Thingiverse
Last crawled date: 3 years ago
This device is designed to hold a cotton ball soaked in your favorite scent locked in a pretty air-flow restricted chamber and then connect that scent to a number of different connectors.
Included are connectors for:
Standard 40mm nato threaded gasmasks
The 'NosePiece' can be used as a stand-alone oral/nasal inhaler, or connected to a standard padded CPR mask.
The 'NosePillowAdapter' can be used with a standard 'Nose Pillow' found on Amazon: https://www.amazon.com/dp/B06XGLKFFH/
There is one redundant part in the design depending on how you want to assemble it. Either print the 'ValvePlate' or 'Flat_Plate' but you will not need both.
If you print the 'Valve Plate' you will want to glue that part to some kind of light-weight plastic film as either plate is designed to prevent air from flowing backwards through the device.
Assembly:
First assemble the 'ValvePlate' if you want to use that part instead of the 'Flat_Plate'.
Then, place the plate into the 'ValveBody' component (the plate should be loose in the 'Valve Body' so that it forms a one-way airflow seal).
Then carefully glue 'ValveBody' to the 'PrimaryBody' - again being sure to allow the plate free-movement.
Then you can use any of the other adapters to connect it how you wish.
Included are connectors for:
Standard 40mm nato threaded gasmasks
The 'NosePiece' can be used as a stand-alone oral/nasal inhaler, or connected to a standard padded CPR mask.
The 'NosePillowAdapter' can be used with a standard 'Nose Pillow' found on Amazon: https://www.amazon.com/dp/B06XGLKFFH/
There is one redundant part in the design depending on how you want to assemble it. Either print the 'ValvePlate' or 'Flat_Plate' but you will not need both.
If you print the 'Valve Plate' you will want to glue that part to some kind of light-weight plastic film as either plate is designed to prevent air from flowing backwards through the device.
Assembly:
First assemble the 'ValvePlate' if you want to use that part instead of the 'Flat_Plate'.
Then, place the plate into the 'ValveBody' component (the plate should be loose in the 'Valve Body' so that it forms a one-way airflow seal).
Then carefully glue 'ValveBody' to the 'PrimaryBody' - again being sure to allow the plate free-movement.
Then you can use any of the other adapters to connect it how you wish.
Similar models
thingiverse
free
toothbrush case by umutcvc
...s one piece, ı recommend you to print as one piece but ı uploaded all the files in case if you want to use just the bottom maybe.
grabcad
free
Flow rate valve for respirators - COVID19
...th sodium bicarbonate. the part that seems like a hook must be not glue with the rest of the other parts under any circumstances.
thingiverse
free
Hermaphroditic connector (The 69 Connector) by atanasovgoran
...tolerances for the molex pins are quite right, they can't get of from the back, but they can from the front of the connector.
grabcad
free
Ball Bearing Design and Assemble In creo Parametric
... of a mechanism without which a mechanism can not work and can not be simulated either.
i hope it will benefit you in many ways.
thingiverse
free
tiny whoop gates by MadeByNozzle
..., we suggest you print these ~3% lager so it is easier to connect to the pieces. you can use hot glue to make the gate permanent.
thingiverse
free
Model for Developer: Mask with Rd 40 adapter. by JangoKamino
...-5 has to manipulate: ripped of the middle to bend it, i used a lighter to warm it up and then bend it.
more later cu
take care
thingiverse
free
Luke Skywalker lightsaber - NO GLUE assembly
...s a separate part and one where its a single piece.
if you need help understanding how to put it all together please contact me!
thingiverse
free
GoPro plate connection by GesehenFPV
...ate with gopro connector.
the target of this connector you are free to use with you want for example using with veldro, straps...
grabcad
free
Oxygen Splitter:Oxys1
...me for my design "oxys1" is because the word oxys is the ancient greek term for oxygen and it is the first of its kind.
grabcad
free
Oxygen Splitter:Oxys1
...me for my design "oxys1" is because the word oxys is the ancient greek term for oxygen and it is the first of its kind.
Thatdrewlion
thingiverse
free
45º Dremel Edge Jig by ThatDrewLion
...thatdrewlion
thingiverse
a modified version of urtxiki's dremel jig designed to hold the edge to round sharp corners easier.
thingiverse
free
Elastic Foreskin Tugger by ThatDrewLion
...on can be adjusted.
it's designed in mm and fits quite comfortably with platex wide mouth nipples as the gripper cut to fit.
thingiverse
free
Hanging LED Lighting by ThatDrewLion
...holster. this way i can hang them up like track lighting over my campsite and enjoy some nice relaxed mood lighting in the woods.
thingiverse
free
Honeywell Half-Mask Gasmask Conversion by ThatDrewLion
... of the mask. you can then slide one of the 'airoutflow' parts over each of the outlets to protect the thin rubber there.
thingiverse
free
40MM Gasmask Magnetic Quick Connect by ThatDrewLion
...arts so that the connecting surfaces were on the top of the print (rather then against the print-bed) created a much better seal.
thingiverse
free
Venus 2000 Receiver/Pump holder by ThatDrewLion
... excess dip from hose-clamp guides before it dries.
link to the hose clamp i use: https://www.amazon.com/gp/product/b00ewo4lic/
thingiverse
free
FR Tugger device by niftymaker
...una versión remixeada del even tension foreskin stretcher de @thatdrewlion esta nueva versión contempla una conexión a presión entre...