Thingiverse
Plaster mold kit by sstarrr
by Thingiverse
Last crawled date: 2 years, 11 months ago
Mold kit for to be cast with plaster of Paris. Can be used to make resin pendants or other items.
Directions:
Place the flat rectangles plates into the bottom of each mold tray, spray each piece with coconut oil spray on all sides for easy release once set.
Pour plaster into mold tray and place the molds into the tray aligning the holes on each corner. Place the mold and tray upright into a vice and gently squeeze them together, top up each mold with plaster.
Once set after 24 hours, carefully remove the top of the mold from the tray being careful to not snap the alignment pins.
Use the pressing tool to release the molds from the bottom and remove the plates from the bottom of each mold, alternately, you can cast in the casting tray halves when aligned with the pins in each corner.
Allow to dry for at least 48 hours.
Spray each mold with release spray or other release agent
Align molds and gently clamp together (preferably with some kind of metal plate on each side to ensure even pressure) and pour casting material into the spout on the top.
Tips:
If the molds aren't entirely flush with each other once cast gently rub them against each other, or on some sandpaper on a flat surface.
Use a bit of salt in the plaster mix to set the mix faster, you will need to work quicker though as it can quite rapidly set the mix.
Give the molds a tap while the plaster is wet to help remove air bubbles in the mold which can be dangerous when casting with your chosen casting material.
Visible holes in the mold can be filled with plaster prior to casting, ensure any filling plaster is completely dry before casting.
Ensure molds are completely dry before casting.
USE SAFETY EQUIPMENT AND PROTECTIVE GEAR (vapor filtered respirator, goggles, apron, welders gloves, leather boots, thick clothing etc) WHEN HANDLING ANY CASTING MEDIUM, CONCRETE OR PLASTER OF PARIS MIX!
Ensure casting is always done preferably outdoors in a well ventilated area away from children and others. Most casting medium is highly toxic especially to women and children.
Disclaimer: I am not responsible for your health and wellbeing. By your act of printing this model and using it to cast models with you are accepting full responsibility for any losses or damage suffered by you or anyone else through your use of them as a cast making device, or for any other use that you use them for.
Printing material: PLA
Wall line count: 3
Infill density: 50% or more
Bottom and top layers: 3
Quality: Fine
Printer: Creality CR-10 Mini
Build program: 3D Builder
Print program: CURA
Directions:
Place the flat rectangles plates into the bottom of each mold tray, spray each piece with coconut oil spray on all sides for easy release once set.
Pour plaster into mold tray and place the molds into the tray aligning the holes on each corner. Place the mold and tray upright into a vice and gently squeeze them together, top up each mold with plaster.
Once set after 24 hours, carefully remove the top of the mold from the tray being careful to not snap the alignment pins.
Use the pressing tool to release the molds from the bottom and remove the plates from the bottom of each mold, alternately, you can cast in the casting tray halves when aligned with the pins in each corner.
Allow to dry for at least 48 hours.
Spray each mold with release spray or other release agent
Align molds and gently clamp together (preferably with some kind of metal plate on each side to ensure even pressure) and pour casting material into the spout on the top.
Tips:
If the molds aren't entirely flush with each other once cast gently rub them against each other, or on some sandpaper on a flat surface.
Use a bit of salt in the plaster mix to set the mix faster, you will need to work quicker though as it can quite rapidly set the mix.
Give the molds a tap while the plaster is wet to help remove air bubbles in the mold which can be dangerous when casting with your chosen casting material.
Visible holes in the mold can be filled with plaster prior to casting, ensure any filling plaster is completely dry before casting.
Ensure molds are completely dry before casting.
USE SAFETY EQUIPMENT AND PROTECTIVE GEAR (vapor filtered respirator, goggles, apron, welders gloves, leather boots, thick clothing etc) WHEN HANDLING ANY CASTING MEDIUM, CONCRETE OR PLASTER OF PARIS MIX!
Ensure casting is always done preferably outdoors in a well ventilated area away from children and others. Most casting medium is highly toxic especially to women and children.
Disclaimer: I am not responsible for your health and wellbeing. By your act of printing this model and using it to cast models with you are accepting full responsibility for any losses or damage suffered by you or anyone else through your use of them as a cast making device, or for any other use that you use them for.
Printing material: PLA
Wall line count: 3
Infill density: 50% or more
Bottom and top layers: 3
Quality: Fine
Printer: Creality CR-10 Mini
Build program: 3D Builder
Print program: CURA
Similar models
thingiverse
free
2014 holiday ornament mold tray by mikelkunz
...tray.
mix plaster of paris and pour into your silicone mold.
remove the finished plaster ornament.
paint, decorate, repeat!
thingiverse
free
Vibration Isolating Silicone Dampers by Mochaboy
.....then let it sit and cure. once it's cured - remove the top of the mold then trim with a sharp pair of scissors.
enjoy :)
thingiverse
free
Flexy-Hand 2 multi-part hinge molds by crashwebster
... hinges. the multi-part design makes removal a snap. be sure to spray the inside of the mold with a release agent before casting.
thingiverse
free
Ticket to Ride America Organizer by bencolt45
...ign board game inserts for any other games, i welcome suggestions! if i do not have the game, donations can help me acquire them!
thingiverse
free
Street light mold by impY
...le it to fit your needs.
for the best results you might want to sand the mold a bit after printing to make sure it's smooth.
cg_trader
$4
Minimalist planter mold - 3D pot printing | 3D
...next use. mould 3dprint concrete mold pla vase pot planter cement pour diy handmade minimalist geometric decor cast casting house
grabcad
free
Edging Brick Mold, Circular Pattern
...uick-set concrete, sand, a tan colorant and a liberal amount of mold release / non-stick spray as well. project pics coming soon.
thingiverse
free
plasticine mold
...hell for plasticine mold.
fill shell with plasticine, imprint object for casting. fill with plaster of paris to duplicate parts.
cg_trader
$4
Soccer Ball Planter mold - 3D Pot Printing | 3D
...ot plant planters decor concrete minimalist cast reusable soccerball football geometric shape printable hobby diy hobby diy other
thingiverse
free
100 "00" Capsule Filler Machine
...ed, and then you are done. (you will normally hear a click when a capsule is closed.)
*note: top half is the small capsule plate.
Plaster
3ddd
$1
Plasters
...plasters
3ddd
plaster
enjoy
3ddd
$1
Decorative plaster
...decorative plaster
3ddd
decorative plaster
3ddd
$1
Decor plaster
...decor plaster
3ddd
decor plaster
3d_ocean
$2
Decorative plaster
...decorative plaster
3docean
arab arabic decorative plaster door islam islamic single wall
decorative plaster
3ddd
$1
Sealing Plaster
...sealing plaster
3ddd
розетка
decorative sealing plaster
3ddd
$1
plaster
...plaster
3ddd
молдинг
3dsmax2013+vray
3d_ocean
$3
Plaster 1
...plaster 1
3docean
a seamless tileable plaster texture with bump and normal maps.
3d_export
free
plastered wall
...plastered wall
3dexport
plastered mud wall texture base jpeg texture.
3ddd
$1
symmetric islamic plaster
...symmetric islamic plaster
3ddd
plaster islamic
symmetric islamic plaster
3d_ocean
$3
Plaster 2
...plaster 2
3docean
a seamless tileable plaster texture with diffuse, ao, bump and normal maps.
Mold
3ddd
$1
molding
...molding
3ddd
молдинг
molding
3ddd
$1
molding
...molding
3ddd
молдинг , резьба
molding
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
3d_export
$10
molding
...molding
3dexport
molding, casting, baguette, decoration
design_connected
$16
Mold
...mold
designconnected
eternit mold computer generated 3d model. designed by charlot, michel.
Kit
turbosquid
$3
Bathroom Kit Baño kit
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Kit
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$20
Drift Kit
...drift kit
3dexport
turbosquid
$40
BitCoin Kit
...urbosquid
royalty free 3d model bitcoin kit for download as on turbosquid: 3d models for games, architecture, videos. (1519068)
turbosquid
$9
Industrial kit
...osquid
royalty free 3d model industrial kit for download as on turbosquid: 3d models for games, architecture, videos. (1144117)
turbosquid
$6
Kit Vases
...
turbosquid
royalty free 3d model kit vases for download as on turbosquid: 3d models for games, architecture, videos. (1285114)
turbosquid
free
Survival Kit
...rbosquid
royalty free 3d model survival kit for download as on turbosquid: 3d models for games, architecture, videos. (1637721)
turbosquid
$50
Ninja Kit
...rbosquid
royalty free 3d model ninja kit for download as fbx on turbosquid: 3d models for games, architecture, videos. (1672364)
turbosquid
$35
Brushes Kit
...osquid
royalty free 3d model brushes kit for download as max on turbosquid: 3d models for games, architecture, videos. (1216721)
turbosquid
$19
Medical kit
...osquid
royalty free 3d model medical kit for download as fbx on turbosquid: 3d models for games, architecture, videos. (1486089)