Thingiverse
PiZeroMount by ScottieD369
by Thingiverse
Last crawled date: 3 years, 1 month ago
Here's a Raspberry Pi Zero mount so that you can mount it to something else!
Since nobody else had made one I had to design it! Because I had a project in mind that I needed the use for it! It's a tight fit but it will get in and be flush. Easy removal of TF card.
Since nobody else had made one I had to design it! Because I had a project in mind that I needed the use for it! It's a tight fit but it will get in and be flush. Easy removal of TF card.
Similar models
3dwarehouse
free
P-198 'Ultima'
...p-198 'ultima'
3dwarehouse
i had nothing else to make...
thingiverse
free
Mug by pimage
...lem exporting the joint for the handle so it might be a bit different from the second picture, i had to re-render for the image).
3dwarehouse
free
My sister's dream house
...ster's dream house
3dwarehouse
i sat down with my sister and i made her the house of her dreams... i had nothing else to do!
thingiverse
free
Parametric bike flashlight mount substitute by NeoTheFox
...mount substitute by neothefox
thingiverse
i've had a flashlight for a bike, but it's mount broke. this is a replacement.
thingiverse
free
iMac PS4 Camera Mount by ChrisMayhew
...make a mount for the top of my imac. not sure if anyone else would require such a design but i thought i'd put it out anyway!
thingiverse
free
OSN MX600 Tripod Mounting Plate by akaie
... the screw will be loose, something i might fix in the future. its designed with a 1/4 inch standard screw that's 17 mm long.
thingiverse
free
Focal tripod mount shoe by stevecooley
...nloaded it from thingiverse, but i also have the openscad file, and it doesn't look like anyone else wrote it, so here it is.
thingiverse
free
ATX PSU Corner Mount by firejackal
...breaking off cause i had a support piece of wood under the psu.
i am sharing this on here just in case someone else could use it.
thingiverse
free
Panda Multirotors Cavity parts by mfish
...panda multirotors cavity parts by mfish
thingiverse
could not find anyone else's mounts so i made my own.
thingiverse
free
Adjustable rod mount for impromptu printers, 1" slot spacing by flemdogmillionaire
...ere i could directly mount the smooth rods for my z axis. so i made this. it's not much, but it'll do the job, hopefully.
Scottied369
thingiverse
free
Chillum Holder by ScottieD369
...chillum holder by scottied369
thingiverse
holds upright
thingiverse
free
Jet Ski Key by ScottieD369
...jet ski key by scottied369
thingiverse
jet ski key
thingiverse
free
PIR MOUNT by ScottieD369
...pir mount by scottied369
thingiverse
i made a pir sensor mount. doesn't hold as is. just add super glue.
thingiverse
free
Icon Box by ScottieD369
...our own caps or select some pre-cut ones i made already.
icon box caps page >>>https://www.thingiverse.com/thing:2788475
thingiverse
free
U bracket for motorcycle handlebars by ScottieD369
...ebars by scottied369
thingiverse
i friend of mine asked me to design one for him and print it so i thought to share my version.
thingiverse
free
Spark Gap by ScottieD369
...s.https://www.cirris.com/learning-center/calculators/50-high-voltage-arc-gap-calculator
this setup you can adjust from (0-8.55mm)
thingiverse
free
Icon Box Caps by ScottieD369
... to make .svg file. then insert svg in project to use for a cut.
main project: icon boxhttps://www.instructables.com/id/icon-box/
thingiverse
free
Dryer Vent to 120MM FAN by ScottieD369
... i did pilot drill some holes into the print. then i found some foam padding i can stick inside so that no bugs can crawl inside!
thingiverse
free
4 Channel Relay Solid Mount Snug & Snap Fit by ScottieD369
...m/thing:1285305
i have made code for raspberry pi touchscreenhttps://gist.github.com/scottied369/0aa1ffe21cc59ade7e1899e7a8243d2f