Thingiverse
Pipe Diamieter Reduction Fitting by ripetomatofetish
by Thingiverse
Last crawled date: 3 years, 4 months ago
This is a simple pipe diameter reduction, where on one end you enter a larger pipe into the part, and on the other end the part goes into a smaller pipe. Good for gutters, air ducts etc.
PLA may not be a good choice here. PETG or ABS should do the job.
PLA may not be a good choice here. PETG or ABS should do the job.
Similar models
thingiverse
free
Tube reduction 12x34 by Penax
...tube reduction 12x34 by penax
thingiverse
tube reduction 12x34 to the waste pipe.
thingiverse
free
Pipe hose Reduction - Hydroponics by mati_chomi
...ingiverse
pipe reduction made on sketchup
used for my hydroponic system.
1/2 inch in and a 5mm out for the aquarium tubing.
thingiverse
free
Reduction for Vorwerk kobold EB370 by lukin
...rse
i made this reduction for vorwerk kobold eb370 vacuum cleaner. reduction is for pipe which is 35 mm diameter. material: pla.
thingiverse
free
Miniature Railway Vacuum Brake Reservoir by peter_the_steam
...pe for the actual joints. if your printer does not seal properly, then give the ends a couple of coats of undercoat to seal them.
thingiverse
free
garden pipe end holder by oferfrid
...garden pipe end holder by oferfrid
thingiverse
garden pipe end holder for trimming the end of the pipe
thingiverse
free
Pipe mount for Slim Jim ham radio antenna by Proxy303
...except fits onto the end of the pipe instead.
tophook is used the same as pipehook, except fits onto the end of the pipe instead.
thingiverse
free
Hookah (no Pipes) by DeathShiva
...ice: madness returns. feel free to remix it. it has no pipe ends, but i figure that's probably good to add in your own hoses.
thingiverse
free
Reduction trapezoidal nut T8 from Prusa to China by Jarins
... after screwing together of both parts it is necessary to drill holes for 3 mm screws to mount the new nut t8 from china products
thingiverse
free
Pipe valve reduction G 3/8"
...pipe valve reduction g 3/8"
thingiverse
g 3/8" to 7,55mm
thingiverse
free
simple pipe end cap by Spirit00
...ipe end cap by spirit00
thingiverse
i was in need for a pipe end cap in my garden to close a pipe end. so here is my solution...
Reduction
thingiverse
free
reduction bobine PLA - coil reduction PLA by plumachau
...reduction bobine pla - coil reduction pla by plumachau
thingiverse
reduction bobine pla - coil reduction pla
thingiverse
free
Bose Reduction by BeStRiPeR
...bose reduction by bestriper
thingiverse
is the reduction of the standard support bose speakers.
thingiverse
free
Tube Reduction by NicoNeo
...tube reduction by niconeo
thingiverse
test model tube reduction 100mm to 99,5mm
thingiverse
free
Hp pen reduction
...hp pen reduction
thingiverse
pen reduction for hp plotters. especially for special pcb pens.
thingiverse
free
Reduction of vibration dampers by urusa
...reduction of vibration dampers by urusa
thingiverse
reduction of vibration dampers
thingiverse
free
ETA Robot reduction by geniv
...eta robot reduction by geniv
thingiverse
reduction for eta robor
thingiverse
free
Reduction for IBC barrel
...reduction for ibc barrel
thingiverse
reduction from 110 mm tube to 70 mm tube into ibc tank (inlet and overflow).
thingiverse
free
Gas mask reduction
... sure that it is gas tight. (it close gaps between layers).
use at your own risk! it is not designed for use against real danger.
thingiverse
free
Tube reduction 12x34 by Penax
...tube reduction 12x34 by penax
thingiverse
tube reduction 12x34 to the waste pipe.
thingiverse
free
Reduction for a clima by Majkeen
...atisation
inner diameter is 150mm
outer rectangle is 150x185mm
inner output rectangle is 130x165mm
used black pet-g 1,75 filament
Pipe
thingiverse
free
Pipe Rack for 4 pipes by hugomir
...pipe rack for 4 pipes by hugomir
thingiverse
pipe rack for 4 pipes -
thingiverse
free
pipe labeling with pipe clamps by gerdo
...pipe labeling with pipe clamps by gerdo
thingiverse
label a pipe using pipe clamps
thingiverse
free
pipes by Syzguru11
...pipes by syzguru11
thingiverse
pipes
thingiverse
free
pipe by miminadeo1980
...pipe by miminadeo1980
thingiverse
pipe
thingiverse
free
Pipes for the Matchbox 10D Pipe Truck by ReadTheFactoryManual
...pipes for the matchbox 10d pipe truck by readthefactorymanual
thingiverse
pipes for the matchbox 10d pipe truck
thingiverse
free
Sewer pipe cap for 110 mm pipes
...sewer pipe cap for 110 mm pipes
thingiverse
a pipe cap for 110 mm sewer pipes.
thingiverse
free
Mouthpiece for pipe
...mouthpiece for pipe
thingiverse
mouthpiece for pipe
thingiverse
free
double pipe
...double pipe
thingiverse
double pipe
thingiverse
free
pipe by SkyLeopard
...pipe by skyleopard
thingiverse
a pipe for reddit user
thingiverse
free
Pipe Stand
...pipe stand
thingiverse
simple pipe stand to display or hold your pipe between packing and puffing.
enjoy!
Fitting
thingiverse
free
High Quality Filament Box Fittings (6mm pneumatic push fit fittings) by therealarod
...6mm pneumatic push fit fittings) by therealarod
thingiverse
high quality filament box fittings (6mm pneumatic push fit fittings)
thingiverse
free
6mm Push Fit Fitting Clip by SurgeFF
...6mm push fit fitting clip by surgeff
thingiverse
a real simple retaining clip for 6mm tubing.
thingiverse
free
Hose Fitting by lowenski
...hose fitting by lowenski
thingiverse
hose fitting
thingiverse
free
Tapered fitting by abessetti
...tapered fitting by abessetti
thingiverse
tapered fitting
thingiverse
free
T fitting by abessetti
...t fitting by abessetti
thingiverse
t fitting
thingiverse
free
Sonication Fitting by evanfloyd570
...r with a hole to fit a 50ml plastic test tube. there is a channel on the lid to allow for the spout of the beaker to fit through.
thingiverse
free
Bathroom fitting by Sunstream
...bathroom fitting by sunstream
thingiverse
fitting for bathroom appliances
thingiverse
free
Water Tap Fitting
...water tap fitting
thingiverse
water tap fitting
thingiverse
free
Fitting Blocker by PowerSupplyUnit
...fitting blocker by powersupplyunit
thingiverse
3d printer fitting blocker
thingiverse
free
Manifold fitting by abessetti
...manifold fitting by abessetti
thingiverse
manifold fitting, hot tub