Thingiverse
Piezoelectric Pneumatic Valve by Ndrew
by Thingiverse
Last crawled date: 3 years, 1 month ago
A prototype electric valve designed for printability. After it has been tested and tuned I'll probably redesign it for better airflow and faster printing.
Each time the piezo transducer is supplied current it should flex, idealy upward. This should allow a .1 mm gap between the bottom of the transducer and the top of the outlet 'cone', allowing the air to escape through the hole in the middle of the bottom half and out the side.
If all goes well I would like to use this to power my other thing:
Wobble Ring Stepping Motor.http://www.thingiverse.com/thing:33853
Imagine: a steam powered reprap :P
I designed it around the 20mm wide piezo element sold by sparkfun:https://www.sparkfun.com/products/10293?
For better printability, I borrowed whosawhatsis' teardrop hole code.http://www.thingiverse.com/thing:3457
I am really wondering what kind of throughput I will get out of this, as the piezo flexes so little. Perhaps I will need a second larger valve that is opened by this one.
Any ideas on how to better seal the whole thing up so that it doesn't leak out the sides/top would be great.
This is my second thing, I hope it is at least interesting to look at. All advice welcome.
Each time the piezo transducer is supplied current it should flex, idealy upward. This should allow a .1 mm gap between the bottom of the transducer and the top of the outlet 'cone', allowing the air to escape through the hole in the middle of the bottom half and out the side.
If all goes well I would like to use this to power my other thing:
Wobble Ring Stepping Motor.http://www.thingiverse.com/thing:33853
Imagine: a steam powered reprap :P
I designed it around the 20mm wide piezo element sold by sparkfun:https://www.sparkfun.com/products/10293?
For better printability, I borrowed whosawhatsis' teardrop hole code.http://www.thingiverse.com/thing:3457
I am really wondering what kind of throughput I will get out of this, as the piezo flexes so little. Perhaps I will need a second larger valve that is opened by this one.
Any ideas on how to better seal the whole thing up so that it doesn't leak out the sides/top would be great.
This is my second thing, I hope it is at least interesting to look at. All advice welcome.
Similar models
thingiverse
free
12 Volt Power Supply Cover - Remixed v2 by Xyk0
...d one i removed from a dell psu);
made it taller, so cables can fit better inside the cover;
added 2mm holes for optional screws.
thingiverse
free
Din scuba valve cap by submatixsms100
... this where the line is able to come out the side of the cap to allow for better sealing from the elements than the first version
thingiverse
free
DeWalt 611 Air Diffuser ver 1 by menerso
... access to the lock button.
this was my first use of onshape.com cad which is awesome... you should try it out (it's free).
thingiverse
free
Bike phone holder Lower extension with charging hole by Cyberzoid
...iginal thing http://www.thingiverse.com/thing:256213
original file and step export included.
tldr: 20mm longer and charging hole.
thingiverse
free
Kcs Yubikey cover
... would unintentionally fall out of the cover
it should be attachable to a key chain
so this is what i came up with... have fun :)
thingiverse
free
iPhone Dock for Side Display by ChrisMagno
...i do not have my own i-device, so i grabbed measurements for the connector base from here: http://www.thingiverse.com/thing:9459
thingiverse
free
Goes to 11 Wheelchair Joystick by Liv2xplore
...d out the bottom, and added a hole for the joystick to mount on my wife's permobile power wheelchair. did it all in tinkercad
thingiverse
free
My Second Spinning Top by KenR
...d it's just as nice as the first. i've printed it in pla but it should come out fine in any other filament type. enjoy!
thingiverse
free
Drill Jig for 20mm Piezo Disk by trevmas
...verse.com/thing:2319993https://www.precisionpiezo.co.uk
for my ormerod 2 mount look at:-https://www.thingiverse.com/thing:2834328
thingiverse
free
Printer Cabinet iPhone 5s Mount by hbh7
... at least some cases, but definitely not thicker ones unless you scale it a bit.
monitoring app used is octoclient for octoprint
Ndrew
thingiverse
free
S&W 40 Clip Holster (DRAFT) by Ndrew
... holster (draft) by ndrew
thingiverse
a clip holster for a double stack mag.
update: made the belt slot wider for thicker belts.
thingiverse
free
Bellowed Air Piston (100% printable) by Ndrew
...to make a "pneumatic stepper motor" like my other thing:http://www.thingiverse.com/thing:33853
any feedback is welcome.
thingiverse
free
Wobble Ring Stepping Motor v2 SV by Ndrew
...'s fastener library
thingiverse.com/thing:15915
also uses mechadense's epi-hypocycloids from:
thingiverse.com/thing:28237
thingiverse
free
Wobble Ring Stepping Motor V2!! by Ndrew
...mm to be productive. i also don't know how easy it will be print 45 degree overhangs that are airtight and slightly flexible.
thingiverse
free
The Wobble Ring Stepping Motor MK1 by Ndrew
...m first.
oh and for now there are no solenoids included. at this point i really don't know enough yet to design capable ones.
Piezoelectric
3d_export
$15
Buzzer 3D Model
...3d model 3dexport buzzer beeper audio electronic component signalling piezoelectric disk alarm timer electric piezo industrial part electrical bell...
thingiverse
free
Support for piezoelectric ceramics by VictorSeino
...pose of uploading this design here is to openly share it. so that everyone that wants to reproduce my research are able to do it.
thingiverse
free
fumigène piézoélectrique (Piezoelectric smoke) by CMNC71
...zoelectric smoke with continuous feed to the plate by gravity. used in our boats for chimneys to replace traditional resistances.
thingiverse
free
CR-10 Piezoelectric Mount e3d v6 by Festivejelly
...uty e3d mod" by chito. i may also add some of my own "wings" as soon as i get a bit more competent with modelling.
thingiverse
free
Anger-o-lantern by Xials
...inside-out. this is designed to be used with a piezoelectric mister so that fog/smoke comes out of his fuming...
thingiverse
free
Tennis Racquet V2 by johntoth
...tennis racquet v2 that could possibly hold accelerometer, gyroscope, piezoelectric sensor at the top near the head of the...
thingiverse
free
Qav-x 210 Clone Skirt by Stewpid
...210mm clones. there is a place to mount a piezoelectric beeper (12mm dia.) as well as a shelf to...
thingiverse
free
Clarinet Barrel Pickup by jolang
...clarinet barrel with a hollow for a 12mm 2-terminal piezoelectric acoustic generator (known as piezo buzzer). use acetone-based glue...
thingiverse
free
Shearwater Perdix Shim Block by Scubapeks
...block by scubapeks thingiverse i had problems with the piezoelectric buttons getting triggered by my drysuit (with thick thermal...
Pneumatic
3d_export
$7
pneumatic charging car
...pneumatic charging car
3dexport
pneumatic charging car
turbosquid
$20
pneumatic flap
...model pneumatic flap for download as dxf, ige, stl, and sldas on turbosquid: 3d models for games, architecture, videos. (1410890)
turbosquid
$2
pneumatic actuator
...l pneumatic actuator for download as 3ds, obj, blend, and stl on turbosquid: 3d models for games, architecture, videos. (1333375)
turbosquid
$30
Cylinder pneumatic
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
booster pneumatic
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Pneumatic Fitting
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
pneumatic wheel
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Pneumatic Unit 3D Model
...pneumatic unit 3d model
3dexport
pneumatic unit pressure velocity
pneumatic unit 3d model fau 71223 3dexport
turbosquid
$3
Pneumatic grinder
...r download as 3ds, dxf, obj, xsi, wrl, fbx, dwg, dae, and skp on turbosquid: 3d models for games, architecture, videos. (1389593)
3d_export
free
pneumatic manifold block
...atic manifold block
3dexport
modified pneumatic manifold block for shooting particles, using festo valves installed on its face.
Valve
3d_export
$5
Valve
...valve
3dexport
diverter valve
3d_export
$5
valve
...valve
3dexport
this is a 3d model of a valve available in all formats.
3d_export
free
valve
...valve
3dexport
simple valve 3d model, more free models here:
3d_export
$20
gate valve
...gate valve
3dexport
gate valve
3d_export
$10
stop valve
...stop valve
3dexport
stop valve
3d_export
$5
ball valve
...ball valve
3dexport
ball valve
turbosquid
$14
Valve
...e
turbosquid
royalty free 3d model valve for download as c4d on turbosquid: 3d models for games, architecture, videos. (1217741)
3ddd
$1
valve 02
...valve 02
3ddd
клапан
water valve
3ddd
$1
Valve 01
...valve 01
3ddd
клапан
water valve
turbosquid
$19
Valve
...royalty free 3d model valve for download as ige, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1425806)