Thingiverse
Phone holder by Fredric
by Thingiverse
Last crawled date: 3 years, 1 month ago
Phone holder adjustable in three angles.
Use:
2 x M3 screw 32mm long.
2 x M3 nylock nut.
2 x M3 4mm long, with a countersunk head.
Drill the two holes to be tapped for M3 screws with 2.5 mm drill.
The other holes are drilled 3mm.
Glue rubber on the bottom for grip.
Use:
2 x M3 screw 32mm long.
2 x M3 nylock nut.
2 x M3 4mm long, with a countersunk head.
Drill the two holes to be tapped for M3 screws with 2.5 mm drill.
The other holes are drilled 3mm.
Glue rubber on the bottom for grip.
Similar models
thingiverse
free
Universal Tripod Phone holder with screw hole by logo8925
...ole is 1/4 inch.
you need to be patient and use a bit force at first to drill it in (create screw thread).
then it works fine.
:)
thingiverse
free
Phone Repair: LCD Holder by umutesenkal
...y umutesenkal
thingiverse
basic lcd holder during the lcd replacement for both phones and tablets.
2 x m3 10mm screws & nuts
thingiverse
free
Window holders (long,medium,short) by Sergei000
..., 29 cm
the distance between the holes on the window frame 25 or 30mm
1 x m3 nut or no
1 x m3x12 screw or 1 x m3x10 screw
2 screw
thingiverse
free
Cable Holder Adapter for IVAR Shelves by hackup
...the latter.
you'll need:
2 of the adapters
2 m3 screws at least 16mm long
2 m3 nuts
1 cable holder linked above
an ivar shelf
thingiverse
free
ROBO3D 60mm RAMPS Fan Bracket by 58webbing
...les in the case. tap the 2 off small holes m3 to take the fan screws. use 2 off 3mm spacers 6mm long as shown in photo. job done!
thingiverse
free
spool holder use 623zz by groyer60
...w 12mm-16mm 2
m3 nut 2
m3 washer 4
623zz 2
3mm drill
thingiverse
free
Parametric drill stop by ksuszka
... it till the nut is in the position
gently unscrew the long screw leaving the nut in the place
put the washer and the final screw
thingiverse
free
hole distance meter by Giovanni1965
... tighten the screw and use a gauge to read the hole center spacer.
to assemble it you need two m3 nuts and a 30 mm long m3 screw.
thingiverse
free
Campfire Letter Holder by phillica
...ca
thingiverse
made larger base that screw into sides
print 1 x base
2 x sides
use small drill through holes then screw together
thingiverse
free
Ramps Mosfet Fan Holder by WTKA321123
...et fan holder by wtka321123
thingiverse
needed a holder this is what i am using. works great. i drill holes and use m3 screw-nut
Fredric
thingiverse
free
Tablet stand by Fredric
...ube with a very tight fit.
the holes for the tube may get drilled with 10mm drill, if they are too tight.
tab 10.1 on the images.
thingiverse
free
Fan bracket for step motor driver K8200. by Fredric
...fredric
thingiverse
cooling fan bracket for step motor driver k8200.
use a 40mm fan.
drill the holes to 2.5mm and use m3 screws.
thingiverse
free
VideoBrain cart shells. by Komb
...videobrain cart shells. by komb thingiverse original designed by fredric cj blaholtz in sweden. i removed the facing to...
Phone
thingiverse
free
phone
...phone
thingiverse
phone
thingiverse
free
Phone holder Phone stand
...phone holder phone stand
thingiverse
phone holder phone stand
thingiverse
free
Phone holder Phone stand by MilanSh
...phone holder phone stand by milansh
thingiverse
phone holder 2 is designed for a mask phone
thingiverse
free
Phone Stand for 6 inches Phones
...phone stand for 6 inches phones
thingiverse
i redesigned the phone stand from emikayee to fit a 6 inches phone.
thingiverse
free
Phone holder / phone stand by ebgdae0
...phone holder / phone stand by ebgdae0
thingiverse
phone stand with two angles.
thingiverse
free
phone stand for phones with cases by RC_Tinker
...ses by rc_tinker
thingiverse
modified the phone stand here on thingiverse to hold a phone with a case like a otterbox or others.
thingiverse
free
phone by Witawat
...phone by witawat
thingiverse
phone
thingiverse
free
phone by yung10938
...phone by yung10938
thingiverse
phone
thingiverse
free
Phone stand
...phone stand
thingiverse
phone stand to keep your phone safe o your desk
thingiverse
free
Phone Stand
...phone stand
thingiverse
this is a phone stand that will hold your phone to make it easier to watch movies.
Holder
thingiverse
free
Stubby holder holder
...der
thingiverse
bottom on the holder is sized for a can or bottle. top of the holder is sized for one in a cooler/stubby holder.
thingiverse
free
Soap holder holder
...soap holder holder
thingiverse
it's a holder to hold the famous soap holder.
thingiverse
free
bottle holder Jar holder can holder
...bottle holder jar holder can holder
thingiverse
hole diameter 38.6mm
thingiverse
free
Spool holder holder by vemotion
...spool holder holder by vemotion
thingiverse
pipe holder (16mm diameter)
thingiverse
free
smartphone holder with usb cable holder and key holder
...other of invention
this is my first creation basically smartphone holder with usb cable holder and key holder
i hope you like it
thingiverse
free
Holder of plate holders by budvar
...t; ;) holder for 5 pieces of modular plate holders from dave o https://www.prusaprinters.org/en/prints/15367-modular-plate-holder
thingiverse
free
Pen Holder/card holder by Pinky561
...pen holder/card holder by pinky561
thingiverse
a pen holder/card holder in one.
thingiverse
free
Toilet paper holder with phone holder
...toilet paper holder with phone holder
thingiverse
toilet paper holder with phone holder
thingiverse
free
Radio equipment holder and microphone holder
...radio equipment holder and microphone holder
thingiverse
radio equipment holder and microphone holder
thingiverse
free
Popsicle Holder Holder by billiamthesecond
...popsicle holder holder by billiamthesecond
thingiverse
keep popsicle holders upright so that they can be set down