Thingiverse
PEX tie-down collection by ottomyman
by Thingiverse
Last crawled date: 3 years ago
This is a collection of some simple PEX 1/2" tie-downs I've decided to share from rebuilding my water heater closet and upgrading the plumbing in my house.
The screw holes tightly fit regular drywall and concrete board type screws with countersunk heads. DO NOT crank the screws down too tightly because the countersunk head on the screw can flare and crack the plastic. Just a heads up. Careful installing them.
There are 2 versions of the dual tie-down... one with a centered screw hole, and one with the screw hole on the side. When I ran hot and cold pex together up the corner of one wall, I found that I needed the screw as close to the wall corner as possible so it lined up with the joist under the concrete board. So you have options...
No supports, no rafts, very simple design... strong and should work well printed at almost any infill. I used 40% and had no problem. You could probably go down to 20-25% and get an equivalent result.
Enjoy your plumbing...
The screw holes tightly fit regular drywall and concrete board type screws with countersunk heads. DO NOT crank the screws down too tightly because the countersunk head on the screw can flare and crack the plastic. Just a heads up. Careful installing them.
There are 2 versions of the dual tie-down... one with a centered screw hole, and one with the screw hole on the side. When I ran hot and cold pex together up the corner of one wall, I found that I needed the screw as close to the wall corner as possible so it lined up with the joist under the concrete board. So you have options...
No supports, no rafts, very simple design... strong and should work well printed at almost any infill. I used 40% and had no problem. You could probably go down to 20-25% and get an equivalent result.
Enjoy your plumbing...
Similar models
thingiverse
free
eye plate / tie down by winand
...print preferrably in abs (for strength)
i increased the wall thickness and bottom/top thickness to 1.2mm for additional strength.
thingiverse
free
Skateboard Wall/Ceiling Hanger
...d 3" for my old tony hawk medallion board that has a lot of kickup on both ends.
any questions or suggestions, let me know!
thingiverse
free
Hyppercube SKR 1.3 Case
... to run my wiriing and one of the holes to screw down the cover wasn't lining up with the cover hole so it was moved as well.
thingiverse
free
simple sturdy screw down cable tie
...ngiverse
simple yet sturdy screw down cable clamp/tie, it holds a cable neatly unto for example a wall.
i use 4mm screws with it
thingiverse
free
Motorcycle Helmet wall mount by mOs_cOww
...i have countersunk the hardware holes for an 8mm head drywall screw with an added hole for ease of tightening with a screwdriver.
thingiverse
free
Anet A8 - Y-Axis Linear Shaft Holder by Darkestnoir
...er
or:
four ∅4mm countersunk head screws for a complete set
optional:
the same amount of screws for the second hole of the holder
thingiverse
free
90° Glue Up Corners Clamp by sjdennis
... would recommend printing 8 to create 2 separate units, one for the top corners and one for the bottom corners of the box.
cheers
thingiverse
free
Corner Routing Guide by jsu3960862
...ler putty. use short #4 flat head wood screws to attach.
the image shown is the one i had purchased from amazon. it worked well.
thingiverse
free
Karcher Wall Hanger by cantfindausername
... so i drew this one which is close. there are 2 versions here, one for a countersunk screw the other for a non-countersunk screw.
thingiverse
free
ikea persby plugs by djhoma
...able) plug for those screw holes. also i mounted the shelves upside down (holes facing up) so that nothing is visible from below.
Ottomyman
thingiverse
free
12g to 16g CO2 canister adapter by ottomyman
...g this plastic cup under one it fills the compartment for a 16g and works well.
it was an easy 5-10 minute print, and works well.
thingiverse
free
bottle drying rack (dovetail) by ottomyman
... of course become stronger.
the dovetail joints fit tight, with 0.3mm object to object. you could file the sides to loosen it.
thingiverse
free
CR20xx lithium battery holder cylinder by ottomyman
...de in nicely but not pop off.
i've printed (and revised) this a couple times, so it should work "out of the box".
Pex
3d_export
free
collection of axial press fittings for pex pipes
...s fittings for pex pipes
3dexport
this is collection of axial press fittings for pex pipes. the collection includes next models:
turbosquid
free
Collection of axial press fittings for PeX Pipes
...n of axial press fittings for pex pipes for download as blend on turbosquid: 3d models for games, architecture, videos. (1639018)
3ddd
$1
Смеситель Hansgrohe "PuraVida"
...изменяемым наклоном струи cливной набор push-open 1¼" гибкая подводка pex c накидной гайкой 3/8” подходит для проточных...
3d_export
$22
600900 Compound pendulum jaw crusher
...operations in large and medium-sized mines. the pe and pex jaw crushers produced by sbm are developed by absorbing...
thingiverse
free
pex holder by gadgetstogo
...pex holder by gadgetstogo
thingiverse
this is for 1/2" pex pipe works good
thingiverse
free
DomeStar @ PEX 2016 by glitchpudding
...domestar @ pex 2016 by glitchpudding
thingiverse
pex signage for domestar
thingiverse
free
PEX fitting removal tool for 3/4 inch PEX pipe by klancas165
...pex fitting removal tool for 3/4 inch pex pipe by klancas165
thingiverse
this is a removal fitting tool for 3/4 pex water line.
thingiverse
free
PEX LED Hoop tee
...ex in a loop and bolting it a tripod. i am using inexpensive tripods, the kind used by photographers to hold light or reflectors.
thingiverse
free
PEX Wreath Stabilizer Clip by czajkaej
...ld the pex.
inside the pex, i have 48 leds/meter 2811 pixel strips, controlled by a raspberry pi, running fpp (falcon pi player).
thingiverse
free
Bosch PEX 220 A vacuum hose adapter by lone__wolf
...bosch pex 220 a vacuum hose adapter by lone__wolf
thingiverse
bosch pex 220 a vacuum hose adapter
Tie
archibase_planet
free
Tie
...tie
archibase planet
cravat tie scarf
tie n240308 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
design_connected
$13
Tie
...tie
designconnected
bonaldo tie computer generated 3d model. designed by lipparini, mauro.
3d_export
free
tie
...tie
3dexport
turbosquid
$5
tie
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
archive3d
free
Tie 3D Model
... model
archive3d
necktie tie cravat
tie - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
free
TIE Interceptor
...erceptor
turbosquid
free 3d model tie in for download as fbx on turbosquid: 3d models for games, architecture, videos. (1164790)
archive3d
free
Tie 3D Model
...
archive3d
cravat tie scarf
tie n240308 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$5
Cartoon tie
...urbosquid
royalty free 3d model cartoon tie for download as on turbosquid: 3d models for games, architecture, videos. (1646820)
turbosquid
free
TIE Bomber
...e bomber
turbosquid
free 3d model tie/sa for download as fbx on turbosquid: 3d models for games, architecture, videos. (1164803)
turbosquid
$6
Bow Tie
...turbosquid
royalty free 3d model bow tie for download as stl on turbosquid: 3d models for games, architecture, videos. (1352382)
Collection
3ddd
$1
GIORGIO COLLECTION
...giorgio collection
3ddd
giorgio collection
giorgio collection
turbosquid
$99
Florence collections - furniture collection
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3ddd
$1
Jumbo Collection
...jumbo collection
3ddd
jumbo collection
диван jumbo collection
3ddd
$1
Jumbo collection
...jumbo collection
3ddd
jumbo collection
кресло jumbo collection
3ddd
free
Florence Collections
...florence collections
3ddd
florence collections , кресло
florence collections
3ddd
$1
Giorgio Collection
...и тумбочки giorgio collection , giorgio collection
кровать и тумбочки giorgio collection
3ddd
$1
Jumbo collection
...jumbo collection
3ddd
jumbo collection , капитоне
кресло jumbo collection
3ddd
$1
Giorgio Collection
...giorgio collection
3ddd
giorgio collection
производитель giorgio collection италия
3ddd
$1
Giorgio collection
...giorgio collection
3ddd
giorgio collection , круглый
giorgio collection table
3ddd
$1
Florence Collection
...florence collection
3ddd
florence collection
florence collection, текстуры есть