Thingiverse
Part Lamp by elwood127
by Thingiverse
Last crawled date: 3 years ago
A simple I3 lamp to illuminate the hob gear and build plate. Lamp uses (3) 10mm Super Bright LED's, (1) 470 OHM current limiting resistor and a slide on/off switch. Originally spec'd a 68 ohm but lights started fading after a few weeks. The wiring is based on a 12volt supply. Positive lead goes to middle post on the switch, out of switch to 470 ohm resistor, out of resistor to positive lead of led (1). From there led's connect negative to positive with the final led negative connecting to the ground from the power supply. Sorry, I forgot to convert the stl to metric. Good to go now.
Similar models
thingiverse
free
Targa Pylon by FlynnD273
...fits onto the base from above, then you glue the pylon on top in the indent. the bottom of the base slots in and twists to close.
thingiverse
free
Fibonacci Spiral Night Light by elwood127
...s upside down. it is correct now. thanks.
i would change the 68 ohm resistor for a 470 ohm. led's started to dim over time .
thingiverse
free
Raspberry Pi Switched LED Nightlight
...istor
i've gone as high was 8 whites, or 6 reds powered from a 12v supply, but that's overkill for that small of a light.
thingiverse
free
Lighted Fan Duct by Vyrago
... positive cable connects to one of the v+ terminals on the power supply, the negative cable connects to one of the com terminals.
grabcad
free
Resistor 10k-1k-470-330 Ohms Pitch 10mm
...tor 10k-1k-470-330 ohms pitch 10mm
grabcad
pitch - 10 mm
resistor 10k
resistor 1k
resistor 330
resistor 470
all of them 1/4 watt
thingiverse
free
Gen 5 Camaro Side Markers by JEBariffic
...arker with hot glue. cover harness and leads with hot glue. allow to cool.
press in makers into position and hold for ~ a minute.
thingiverse
free
PS Move DIY VR Headtracker by Nanafalke
...nto the lid and the ball from above. close the lid and you are done.
for software setup, watch the video on daleytechs channel.
thingiverse
free
LED Circuit Board Class Activity by robertvarney1
...tor (yellow,violet,brown)
-9 volt battery
-9 volt battery connector (with stripped positive and negative leads)
-conductive paint
thingiverse
free
USB desk lamp by K_Sherman
...once i've tested the bulb i pot the assembly in hot melt glue.
for hardware i use 2x 1/4-20 x 1in bolts and 2x 1/4-20 nuts.
thingiverse
free
Bear night light by Jaenne
...ar night light by jaenne
thingiverse
you will need :
3 or 4 standard led
1 resistance 470 ohms
1 battery 9 volts
1 light switch
Elwood127
thingiverse
free
Top (Repaired) by elwood127
...top (repaired) by elwood127
thingiverse
repaired file.
thingiverse
free
Card Holder by elwood127
...card holder by elwood127
thingiverse
simple card holder.
thingiverse
free
Tea Set by elwood127
... scaled it up to 1.5 and redrew the cups to be a little beefier and print friendly. great for little girls or tea pot collectors.
thingiverse
free
J Head Mounting Bracket by elwood127
... elwood127
thingiverse
originally designed for the prometheus v2 hotend. has standard j head features.
uses a bowden tube setup.
thingiverse
free
Beer Keg Tap Drip Tray by elwood127
...rip tray by elwood127
thingiverse
a simple anti-splash drip tray that sits at the base of a standard keg.
two part construction.
thingiverse
free
Prusa I3 Feet by elwood127
... endstop mounts
on both sides of the foot. included are (2) endstop spacers for the y
horizontal slot to easily align y carriage.
thingiverse
free
I Love You Desk Gift by elwood127
...i love you desk gift by elwood127
thingiverse
1/2 inch thick x 3/4 inch tall x 4 inch long.
thingiverse
free
Mothers Birthday Heart by elwood127
... wide x 6 inches tall. i printed in red and used a flat eraser dipped in white paint to highlight the raised lettering and heart.
thingiverse
free
Z605 Prusa I3 Extruder Motor Fan Bracket by elwood127
...z605 prusa i3 extruder motor fan bracket by elwood127
thingiverse
a 40mm fan mounting bracket for the extruder motor.
thingiverse
free
Bender Beer Cozy by elwood127
...rcraft gray, gloss black and white. with or without handle. fresh drawing but inspired by cerberus333 full bender model..thanks.
Lamp
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp table lamp reading lamp
lamp - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Lamp
...lamp
archibase planet
lamp reading lamp table lamp lantern
lamp - 3d model (*.3ds) for interior 3d visualization.
3d_ocean
$6
Lamp
...lamp
3docean
lamp
a high quality lamp.
Part
3d_export
$5
Parts
...parts
3dexport
parts
3d_export
$5
Part
...part
3dexport
part
3d_export
$5
Part
...part
3dexport
machine part
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$65
Part
...part
3dexport
simple rendering of the scene file
3d_export
$30
fan part
...fan part
3dexport
this is a part of fan of pedastal
3d_export
$10
machine parts
...machine parts
3dexport
3d part modeling work ,contact for 3d work
turbosquid
$59
Mechanical Part
...id
royalty free 3d model mechanical part for download as c4d on turbosquid: 3d models for games, architecture, videos. (1410833)
turbosquid
$17
Road parts
...bosquid
royalty free 3d model road parts for download as 3ds on turbosquid: 3d models for games, architecture, videos. (1192967)
turbosquid
$9
Cutter Parts
...squid
royalty free 3d model cutter parts for download as stl on turbosquid: 3d models for games, architecture, videos. (1220010)