Thingiverse
Optimized Nonlethal Door Stop Multitool by ChrisMUC
by Thingiverse
Last crawled date: 3 years ago
Nonlethal Door Stop Multitool
Optimized downside to Maximize the grip performance for holding the door in place, while on the other hand smoothly slipping in under the door when placed. If you want to add more-extra-ultra grip to the downside of the door stop you can use a rubbercoating. I tried the spray-on version of Plastidip and it works really great for this purpose.
For your information, this is what I used: http://www.plastidip.de.com/produkte/plasti-dip-flussiggummi/
And best of it: you can remove the coating easyly if you don't like the result. Probably you can find something similar near you in some DIY store, hardware store, home improvement store or in a shop for car supplies. I found it in an electronics store.
Buckled upside to hold the door in a firm and secure grip.
Extra Big hole (~42mm diameter) with Extra smoothly rounded edges to pull it out comfortably with 2 Fingers or even with gloves.
Safekeeping by hanging it over the handle of the door is possible for most doors due to the Extra Big hole. So you have it at hand in a door stop / self defense emergency.
Easier slipping under the door even with a small gap to the floor, due to smoothly rounded tip and optimized design of the downside of the tip (reduced size of the first to teeth).
Suitable for ~4mm-40mm gaps without scaling. (Just a guess based of the dimensions, to be verified in experiment. Could be up to 50mm max.)
Wall and handle protector. Put it behind the door to avoid slamming the door against the wall. (Try it with the round end facing the door, too. Depending on the size of the handle and the character of the floor this can give better results.)
Windows can be kept open with it, too. (Not talking about the software.) Try to put it in the gap at the hinged side of the window.
Optimized for easy printing on FDM machines (i.e. Ultimaker, RepRap,...). You should be able to print it without outer support, for details see the section instructions.
Childsave. It is big enough that it can't be swallowed and does not have sharp edges. If you print it with the right material it is non toxic, too.
Portable. It is light weight and has an Extra Big hole to grab and attach to things so it is really portable. If you want to transport it with your bike, you could just hang it around the handlebar. You could also attach a string and hang it around your neck for transport. If you transport it with your car you can attach a string to the hole and hang it around your rear mirror as an ornament, too.
No assembly needed. It is just one piece so you don't have to worry about a difficult and time consuming assembly. It is usable right off the printbed.
Customizable. You can add some rubber coating to the downside to adjust the grip needed to the floor and door you want to use.
Nonlethal self defense tool. Hold it with two fingers in the Extra Big hole and just think about it. If you know what a tactical pen is, you know what I mean. Probably this is the first tool you have at hand when the Zombies try to rush into your home... Update: I thought about it again and probably this is not such a good idea, because the Nonlethal Door Stop Multitool is nonlethal and the Zombies are already dead. Seems not to match. You could instead try to impress them with your printing abilities and try to involve them into some kind of communication about it. (It is even more probable that a Zombie will communicate with you about 3D-printing than the Nonlethal Door Stop Multitool will do any serious harm to him or her...) Caution: Update: As Gyrobot mentiond in the comment, there is a chance that the Optimised Nonlethal Door Stop Multitool could be lethal, too. You could bore someone to death with it. I wonder if this could work with the Zombie issue mentiond above....
You can use it as an ornament by hanging it around your neck. The rappers hung alarm clocks around their neck in the '80s, so why not?
You can use it to build a trap. Remove the handle of the door on the inner side, hold the door open with the door stop, attach a tripwire to the door stop. When somebody enters the room they release the door by the tripwire and the door closes. Works best with self-closing doors...
Use it as communication enabler. Just put it on your desk at work. Somebody will ask what it is. And whoosh, you are right in the middle of a 3d-printing discussion. Don't forget to print the Thing Tag. Just in case you are asked... http://www.thingiverse.com/thing:200571/attribution_card
Use it to test your 3d-printer. The Door stop is pretty easy to print, so the frustration factor should be minimal. And after printing you have something useful to play around with. And even if the print is not fully completed, it will probably work to stop a door. And failed prints tend to attract people, who ask you about it. A perfect print is good, but to induce communication a failed print is far better.
Use it as door stop this is what it is intended to be. And it works pretty well for this purpose.
Probably no one here reads so much text, so it seems not to matter so much what else I write here about the mere unlimited possibilities you have with this piece of plastics. But if you have more ideas about how to use this tool, you are invited to post a comment.
Credits
The door stop was build from scratch and
inspired by thing 144708, Stopper of door No2:http://www.thingiverse.com/thing:144708.
The description was inspired by thing 35518, Blockystar:http://www.thingiverse.com/thing:35518
and thing 35560, The Warble Wobble:http://www.thingiverse.com/thing:35560.
Thank you for your inspiration.
The design was developed in FreeCAD. http://www.freecadweb.org
Thank you for making such a powerful software available to the public!
Thank you for visiting!
Chris
Remixes:
Remixed Non-Lethal Door Stop By arod24 [Amauris Rodriguez]:http://www.thingiverse.com/thing:368257
Door Stopper by alexhbaiu [Alex Hbaiu]:http://www.thingiverse.com/thing:563123
Thank you for sharing your creativity!
Optimized downside to Maximize the grip performance for holding the door in place, while on the other hand smoothly slipping in under the door when placed. If you want to add more-extra-ultra grip to the downside of the door stop you can use a rubbercoating. I tried the spray-on version of Plastidip and it works really great for this purpose.
For your information, this is what I used: http://www.plastidip.de.com/produkte/plasti-dip-flussiggummi/
And best of it: you can remove the coating easyly if you don't like the result. Probably you can find something similar near you in some DIY store, hardware store, home improvement store or in a shop for car supplies. I found it in an electronics store.
Buckled upside to hold the door in a firm and secure grip.
Extra Big hole (~42mm diameter) with Extra smoothly rounded edges to pull it out comfortably with 2 Fingers or even with gloves.
Safekeeping by hanging it over the handle of the door is possible for most doors due to the Extra Big hole. So you have it at hand in a door stop / self defense emergency.
Easier slipping under the door even with a small gap to the floor, due to smoothly rounded tip and optimized design of the downside of the tip (reduced size of the first to teeth).
Suitable for ~4mm-40mm gaps without scaling. (Just a guess based of the dimensions, to be verified in experiment. Could be up to 50mm max.)
Wall and handle protector. Put it behind the door to avoid slamming the door against the wall. (Try it with the round end facing the door, too. Depending on the size of the handle and the character of the floor this can give better results.)
Windows can be kept open with it, too. (Not talking about the software.) Try to put it in the gap at the hinged side of the window.
Optimized for easy printing on FDM machines (i.e. Ultimaker, RepRap,...). You should be able to print it without outer support, for details see the section instructions.
Childsave. It is big enough that it can't be swallowed and does not have sharp edges. If you print it with the right material it is non toxic, too.
Portable. It is light weight and has an Extra Big hole to grab and attach to things so it is really portable. If you want to transport it with your bike, you could just hang it around the handlebar. You could also attach a string and hang it around your neck for transport. If you transport it with your car you can attach a string to the hole and hang it around your rear mirror as an ornament, too.
No assembly needed. It is just one piece so you don't have to worry about a difficult and time consuming assembly. It is usable right off the printbed.
Customizable. You can add some rubber coating to the downside to adjust the grip needed to the floor and door you want to use.
Nonlethal self defense tool. Hold it with two fingers in the Extra Big hole and just think about it. If you know what a tactical pen is, you know what I mean. Probably this is the first tool you have at hand when the Zombies try to rush into your home... Update: I thought about it again and probably this is not such a good idea, because the Nonlethal Door Stop Multitool is nonlethal and the Zombies are already dead. Seems not to match. You could instead try to impress them with your printing abilities and try to involve them into some kind of communication about it. (It is even more probable that a Zombie will communicate with you about 3D-printing than the Nonlethal Door Stop Multitool will do any serious harm to him or her...) Caution: Update: As Gyrobot mentiond in the comment, there is a chance that the Optimised Nonlethal Door Stop Multitool could be lethal, too. You could bore someone to death with it. I wonder if this could work with the Zombie issue mentiond above....
You can use it as an ornament by hanging it around your neck. The rappers hung alarm clocks around their neck in the '80s, so why not?
You can use it to build a trap. Remove the handle of the door on the inner side, hold the door open with the door stop, attach a tripwire to the door stop. When somebody enters the room they release the door by the tripwire and the door closes. Works best with self-closing doors...
Use it as communication enabler. Just put it on your desk at work. Somebody will ask what it is. And whoosh, you are right in the middle of a 3d-printing discussion. Don't forget to print the Thing Tag. Just in case you are asked... http://www.thingiverse.com/thing:200571/attribution_card
Use it to test your 3d-printer. The Door stop is pretty easy to print, so the frustration factor should be minimal. And after printing you have something useful to play around with. And even if the print is not fully completed, it will probably work to stop a door. And failed prints tend to attract people, who ask you about it. A perfect print is good, but to induce communication a failed print is far better.
Use it as door stop this is what it is intended to be. And it works pretty well for this purpose.
Probably no one here reads so much text, so it seems not to matter so much what else I write here about the mere unlimited possibilities you have with this piece of plastics. But if you have more ideas about how to use this tool, you are invited to post a comment.
Credits
The door stop was build from scratch and
inspired by thing 144708, Stopper of door No2:http://www.thingiverse.com/thing:144708.
The description was inspired by thing 35518, Blockystar:http://www.thingiverse.com/thing:35518
and thing 35560, The Warble Wobble:http://www.thingiverse.com/thing:35560.
Thank you for your inspiration.
The design was developed in FreeCAD. http://www.freecadweb.org
Thank you for making such a powerful software available to the public!
Thank you for visiting!
Chris
Remixes:
Remixed Non-Lethal Door Stop By arod24 [Amauris Rodriguez]:http://www.thingiverse.com/thing:368257
Door Stopper by alexhbaiu [Alex Hbaiu]:http://www.thingiverse.com/thing:563123
Thank you for sharing your creativity!
Similar models
thingiverse
free
Wall Mount Case for Nonlethal Door Stop Multitool by shahirn
...ded tape to fix it on the wall or anywhere you want.
the door stopper can be found here:https://www.thingiverse.com/thing:200571
3dwarehouse
free
Optimized Nonlethal Door Stop Multitool by ChrisMUC - for CFNA IT dept
...muc published on december 11, 2013 www.thingiverse.com/thing:200571 creative commons - attribution - non-commercial - share alike
thingiverse
free
Doorstop carpet by ellioal
...inspired by the 'optimized nonlethal door stop multitool'.
i needed more grip for a heavy door + thin carpet combination.
thingiverse
free
Thinner Non-leathal Door Stop Multitool by mbainrot
...i've shaved a little off the bottom to enable better bed adheasion without me having to locate my ipa to go and clean the hbp
thingiverse
free
door hook by stevecooley
... on the front door, but i suppose you could hang any arbitrary thing you like. my door is ~43mm thick, so i made this 44mm wide.
thingiverse
free
Extended Wall Mount Case for Nonlethal Door Stop Multitool by Dioragno
...it of brim and support at the base just to help a bit (brim and supports add about 1g of material and 3-4 minutes printing time).
thingiverse
free
Make It Float Challenge Floaty Boat by ISH2020
...e after you painted it or something). you could probably think of many more uses for this boat, and i hope you like my design! :)
thingiverse
free
Dwarven Tower III by TwoRoads
...eople.https://www.thingiverse.com/thing:2760949https://www.thingiverse.com/thing:3968634https://www.thingiverse.com/thing:2958021
thingiverse
free
DOOR OPENER WITH HOLDER AND CLIP by Ivankahl
...s door opener, so nobody things you have a knive :p
please stay safe during this harsh times.
happy 3d printing!
notouchchallenge
3dwarehouse
free
Vispring Castor Grip
...u can use to stop wheels from rolling. simply put this castor grip around the wheels of your bed. the model is ready to 3d-print.
Nonlethal
thingiverse
free
Wall Mount Case for Nonlethal Door Stop Multitool by shahirn
...ded tape to fix it on the wall or anywhere you want.
the door stopper can be found here:https://www.thingiverse.com/thing:200571
thingiverse
free
Extended Wall Mount Case for Nonlethal Door Stop Multitool by Dioragno
...it of brim and support at the base just to help a bit (brim and supports add about 1g of material and 3-4 minutes printing time).
thingiverse
free
Doorstop carpet by ellioal
...designed for use with carpet inspired by the 'optimized nonlethal door stop multitool'. i needed more grip for a...
renderosity
$13
Silent Kill:Knife Poses
...partial arm poses are included, as well:<br /> 6 nonlethal m4 attacker poses<br /> 6 nonlethal v4 attacker poses<br...
thingiverse
free
Bed Roller Stop Craddle for 2 Inch Wheels by 0ops1e
...by 0ops1e thingiverse simple scale and flip of "optimized nonlethal door stop multitool" to hold the 2 inch wheels...
thingiverse
free
Thinner Non-leathal Door Stop Multitool by mbainrot
...a quick and dirty meshmixer remix of the optimized nonlethal door stop multitool i made it thinner because i...
thingiverse
free
Psyco Century - The Insurrection Set by Quickfootie
...pistols for point blank kills and also carry the semi-nonlethal maser rifle. these lightweight weapons are only lethal when...
grabcad
free
PFM-1 AP MINE (Historical Prop)
...more will make it function. the charge is usually nonlethal although sufficient to destroy part of the foot if...
3dwarehouse
free
Optimized Nonlethal Door Stop Multitool by ChrisMUC - for CFNA IT dept
...muc published on december 11, 2013 www.thingiverse.com/thing:200571 creative commons - attribution - non-commercial - share alike
Chrismuc
thingiverse
free
Pocket Sun Dial, foldable by ChrisMUC
...put it in your pocket. (not shown in the pictures)
thanks for visiting.
chris
created with freecad http://www.freecadweb.org/
thingiverse
free
canvas blind end cover by ChrisMUC
... http://www.freecadweb.org
thank you for making such a powerful software available to the public!
thank you for visiting!
chris
thingiverse
free
micro wire wrap spool holder by ChrisMUC
...yly replaced when heated too much while soldering.
thanks vor visiting!
chris
created with freecad http://www.freecadweb.org/
thingiverse
free
Door Stopper by alexhbaiu
...change to reduce sliding on my floor.http://www.thingiverse.com/thing:200571 thank you @chrismuc for helping me move...
thingiverse
free
Buckle strong, easy printable supportless by ChrisMUC
...t-buckle (female)by abrokadabra [kevin abramowski]:http://www.thingiverse.com/thing:664775
thank you for sharing your creativity!
thingiverse
free
Case for ATMEL AVR Dragon by ChrisMUC
...ts of the case with my avr dragon and the different mounting possibilities of the 'wing'.
thank you for visiting!
chris
thingiverse
free
tweezers or forceps with round end by ChrisMUC
...ou can read more about this and what exactly i used here: http://www.thingiverse.com/thing:200571
thank you for visiting!
chris
thingiverse
free
Happy Shopping Cart Coin Holder by ChrisMUC
...design was developed in freecad. http://www.freecadweb.org
thank you for making such a powerful software available to the public!
thingiverse
free
GPS Mount Carbiner Adapter by ChrisMUC
...design was developed in freecad. http://www.freecadweb.org
thank you for making such a powerful software available to the public!
thingiverse
free
darning egg or mushroom, Stopfei oder Stopfpilz by ChrisMUC
...d a darning egg or something similar to fix the holes in the socks. hope you find it useful, too.
thank you for visiting!
chris
Multitool
3d_export
free
z-morph 3dp front hook opt lasers
...this file contains a front hook for the z-morph multitool 3d printer. the hook can be used to mount...
thingiverse
free
card multitool by jvanhook
...card multitool by jvanhook
thingiverse
a quick multitool
thingiverse
free
multitool by norcalz7
...multitool by norcalz7
thingiverse
in progress
thingiverse
free
multitool by norcalz7
...multitool by norcalz7
thingiverse
in progress. commence
thingiverse
free
Parkside multitool wrench by lucibrandus
...parkside multitool wrench by lucibrandus
thingiverse
parkside multitool wrench
thingiverse
free
Multitool
...hingiverse
a multi-tool equiped with:
carpenters square
center finder
metric ruler
45 degree angle
bolts and screws size finder
thingiverse
free
snowboard multitool by norcalz7
...snowboard multitool by norcalz7
thingiverse
yea yea yea
thingiverse
free
Notouch-Multitool by vkngr
...uncher, a paperclip and a reacher-holder for pencils ect. it can be set on a stick and stick can be fixed with a screw or splint.
thingiverse
free
Tacklife Multitool Stand RTD02DC by bvernail
...tacklife multitool stand rtd02dc by bvernail
thingiverse
multitool stand i created using tinkercad.
simple but effective
thingiverse
free
Multitool by gocircuit
...multitool by gocircuit
thingiverse
---needs resizing---
length is only about 30 mm
i found resizing it 6 times is a decent shape
Optimized
turbosquid
$3
VolleyBall Optimized
... model volleyball optimized for download as obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1370381)
turbosquid
free
m4a1 optimized
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
PTERODACTYL Optimized CreatureCharacter
...l pterodactyl optimized creaturecharacter for download as fbx on turbosquid: 3d models for games, architecture, videos. (1705900)
turbosquid
$2
XIOLLA: Optimized Character
...free 3d model xiolla: optimized character for download as fbx on turbosquid: 3d models for games, architecture, videos. (1705725)
turbosquid
$8
Melia Azedarach Optimized
...l melia azedarach optimized for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1634816)
turbosquid
$80
Game Optimized Tools
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$13
Subaru B11S Optimized 3D Model
...ubaru b11s optimized 3d model
3dexport
subaru car cars b11s optimized 3onder
subaru b11s optimized 3d model 3onder 10518 3dexport
turbosquid
$15
Tutanhamon 3D - Unity Optimized
... 3d model tutanhamon 3d - unity optimized for download as fbx on turbosquid: 3d models for games, architecture, videos. (1182225)
turbosquid
$39
Rock Scanned "OPTIMIZED"
...
royalty free 3d model rock for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1292372)
turbosquid
$3
The Dead General Optimized Character Rig
...d model the dead general optimized character for download as on turbosquid: 3d models for games, architecture, videos. (1705429)
Stop
turbosquid
$5
Stop Stop
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
free
stop
...stop
3dexport
classic stop.
3d_ocean
$12
Bus Stop
...bus stop
3docean
bus bus stop station
bus stop model
archibase_planet
free
Bus stop
...bus stop
archibase planet
bus stop bus-stop
bus stop n150111 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
3d_export
$10
stop valve
...stop valve
3dexport
stop valve
archibase_planet
free
Bus stop
...bus stop
archibase planet
bus stop bus-stop bus station
bus stop n070512 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Bus stop
...bus stop
archibase planet
bus stop bus-stop bus station
bus stop n181213 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archibase_planet
free
Bus stop
...bus stop
archibase planet
bus stop bus-stop bus station
bus stop n120514 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
turbosquid
$1
stop
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$9
Stopping Place
...in zip pack the following items: 3d file stopping plac pack/.max/.obj// material and textures. well we hope you enjoy it regards.
Door
3d_export
$5
door handle of doors
...door handle of doors
3dexport
door handle of doors
3d_ocean
$4
Door
...3docean
architecture door gate gothic door old style door
door, 3d door, gothic door, architecture, old style door, gate, 3d gate
3d_ocean
$10
Door
...door
3docean
design door doors home house indoor interior opening doors
door design
archibase_planet
free
Door
...r
archibase planet
door sliding door interior door rail door
door n250515 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Door
...door
archibase planet
door sash door sash-door interior door
door 900 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Door
...door
archibase planet
door sash door sash-door interior door
door 600 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Door
...door
archibase planet
door sash door sash-door interior door
door 800 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Door
...door
archibase planet
door sash door sash-door interior door
door 800 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Door
...door
archibase planet
door sash door sash-door interior door
door 700 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Door
...door
archibase planet
door sash door sash-door interior door
door 600 - 3d model (*.gsm+*.3ds) for interior 3d visualization.