Thingiverse
Oil catchcan by cameron20020
by Thingiverse
Last crawled date: 3 years ago
Update:
Printed and assembled. Smoothed it off with an acetone treatment, then let it dry. Placed it into the oven at 60C to check if it could handle a hot engine bay. NOPE, bubbled up and deformed badly.
Lesson learnt, will either have to print this in something really high temp rated, or have it machined out of metal and threads/seals added to parts for attachment.
My car has a little problem with oil/moisture on it's positive crankcase ventilation circuit, so I've created my own catch can.
I chose not to buy a catch can, because they are overpriced, and sometimes very poorly designed. Some horrible ones are just two hose barbs into a chamber.
For best results, print all parts separately, expose them to acetone vapour treatment to smooth off layer marks & add strength, then glue together as per the .blend file. Use acetone/abs goo glue for strong joins, and install to your car only after it's FULLY DRIED.
TOP PIPIE: outlet to intake manifold low pressure side (before turbo)
MIDDLE PIPE: Inlet from crank case
Lower pipe: To drain container. Must be completely sealed drain container for this separator to work as per design.
Printed and assembled. Smoothed it off with an acetone treatment, then let it dry. Placed it into the oven at 60C to check if it could handle a hot engine bay. NOPE, bubbled up and deformed badly.
Lesson learnt, will either have to print this in something really high temp rated, or have it machined out of metal and threads/seals added to parts for attachment.
My car has a little problem with oil/moisture on it's positive crankcase ventilation circuit, so I've created my own catch can.
I chose not to buy a catch can, because they are overpriced, and sometimes very poorly designed. Some horrible ones are just two hose barbs into a chamber.
For best results, print all parts separately, expose them to acetone vapour treatment to smooth off layer marks & add strength, then glue together as per the .blend file. Use acetone/abs goo glue for strong joins, and install to your car only after it's FULLY DRIED.
TOP PIPIE: outlet to intake manifold low pressure side (before turbo)
MIDDLE PIPE: Inlet from crank case
Lower pipe: To drain container. Must be completely sealed drain container for this separator to work as per design.
Similar models
thingiverse
free
Sink Drain by _PeterLustig1
...t.
for adjusting the height of the drain sink i simply use an m6 screw. if you don't have one, you can print the m6x35 screw.
thingiverse
free
oil drain pan filter holder by scottymizt
...strength. printed on my anet a8 20% fill .20 layer height, i have printed it with pla, abs and flexable filament all worked great
thingiverse
free
Crankcase Fumes Catch Can by HamDesigner
...from the crankcase blow-by gases.
the cap surface is set up to use a 124mm x 3.5mm o-ring. it might seal well enough without it.
thingiverse
free
LED Shroud by RoboHart
...to glue to the two parts together. then brushed the whole part with acetone, this smoothed the finish and make the part stronger.
thingiverse
free
Spill resistant oil can bottle dipper by Paintballmagic
... the remainder. let dry for at least 15 minutes. this will seal the lid to the can. wear gloves and safety glasses!
enjoy!
thingiverse
free
Automotive oil drain pan cap. by secondjohn
...re slightly smaller diameter. designed this one with openscad using dan kirshner's thread library (thanks!). no leaks yet !
grabcad
free
OIL CATCH CAN
...oil catch can
grabcad
car oil catch can
thingiverse
free
House coin bank by h_spasov
...ose how to print it - all in one, separated house and terrain or part by part. i printed parts one by one and glue them together.
grabcad
free
Hydraulic Jack
...r.
i have designed all parts of this jack (valves, seals, mechanical parts, ..etc.) to be manufacture, replace or maintain easly.
thingiverse
free
Threaded Pipe fitting and nut by gonAlonso
...d by acetone vapor to seal any tiny hole. then used any piping glue to seal it in place. screw the nut into the fitting and done.
Catchcan
thingiverse
free
Audi A4 B8 2.0 TFSI PCV delete kit by LV-426
...this is no to be plumbed to an oil catchcanfiltration system. (this may not be legal in a lot...
grabcad
free
Oil Catchcan
...oil catchcan
grabcad
catchcan designed as per formula bharat specs
grabcad
free
catchcan base
...catchcan base
grabcad
project
grabcad
free
Disposable catchcan
...disposable catchcan
grabcad
baffled disposable catch can with 3 ports
grabcad
free
CB600f Catchcan
...alternative to the big original catch can. will fit on the right side of the radiator. rubber cap from original should be reused.
cults
$21
Vacuum Filter CatchCan
....com/watch?v=un0ngzwiwb0
(purchase of this product is for personal use only. for commercial license, please message me directly)
grabcad
free
air filter
...air filter grabcad air filter for catchcan ...
grabcad
free
Catch Can
...catch can grabcad free drwaing of a catchcan for my car i was...
Cameron20020
thingiverse
free
minimal phone/tablet holder by cameron20020
...minimal phone/tablet holder by cameron20020
thingiverse
simple phone/tablet holder
thingiverse
free
Yet another phone holder by cameron20020
...r phone holder by cameron20020
thingiverse
similar to other ones i made,
but more reinforced so less flexing with heavy tablets.
thingiverse
free
funky car by cameron20020
... interesting. i'll be updating this later on, with suspension parts & wheels/gearbox, so then i'll make it an rc car.
thingiverse
free
Phone Holder -remix by cameron20020
...r some unknown reason, there seems to be some corruption/artifacts in the stl file. will probably fix this when i feel motivated.
thingiverse
free
Simple phone holder with honeycomb pattern by cameron20020
...e
drew up extrusion shape in inscape.
made 3d in blender, then put some honeycomb patterns in to make it a little more pretty.
thingiverse
free
Z1 Table holder... with speaker holes by cameron20020
...der from magnum, with speaker holes at the base of the phone slot, so sound may make its way out through the opening at the front
thingiverse
free
rwd car body by cameron20020
... engine/gearbox. maybe one day when i build a much better 3d printer, i'll print this off, and even make an rc car out of it.
thingiverse
free
Seat bag hook by cameron20020
...s.
if your car is not a ds3, print a super thin low infil/thin wall version to check the profile is correct before going all out.
thingiverse
free
LM2577 LM2596 PCB board enclosure by cameron20020
...t print in pla if there's any real load on the converter module. pla will melt before the lm2577/2596 enter thermal shutdown.
thingiverse
free
Waterproof Box by cameron20020
...uot; or slightly change these parts per your printer. make it fit as well as you can so it's better at sealing out the water.
Oil
3d_ocean
$5
Oil Drum
...oil drum
3docean
gas gasoline industry oil oil barrel oil drum petrol petroleum shell texaco
an oil drum
3d_ocean
$12
Oil lamp
...oil lamp
3docean
candle lamp oil traditional
high poly oil lamp model
3d_export
$5
oil derrick
...oil derrick
3dexport
oil derrick
3ddd
$1
oil lamp
...oil lamp
3ddd
лампа
oil lamp
3d_export
$7
oil map
...l gas production displays the full cycle of production and transportation of oil and gas. created in archicad 22. file in archive
turbosquid
$16
Oil
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
oil
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$5
Barrel and Oil Drum
...barrel and oil drum
3docean
barrel oil drum
oil, barrel, drum, game props
3d_export
$5
Oil storage
...oil storage
3dexport
big oil storage or barrel or storage tank 2 formats lwo & obj
3ddd
$1
Olive Oil
... масло , бутылка
fully detailed olive oil
polygon : 129,872
verts: 65,038