Thingiverse
MTW Suppressor by mcmik3
by Thingiverse
Last crawled date: 3 years, 4 months ago
It's a suppressor specifically designed for Wolverine Airsoft MTW. Fits inside the m-lok handguard. Hexagonal pattern on the outside.
Note that you can't mount anything on the sides, or the lower 45° mlok holes. You want to mount a flashlight etc, it needs to go on the upper 45° holes. Grips etc on the bottom are fine.
More volume means better suppression, and I didn't want to make the suppressor any longer, so the first chamber goes back around the barrel. The size is roughly 42mmx200mm.
Use foam/scotch-brite/whatever on the inside. You can also add a layer of painters tape on the baffles and shoot a hole through. Keep in mind that this might affect accuracy, but its better for suppression.
Depending on your printer, some parts might need some grinding to make a tight fit.
There is an option for a M4 brass insert to secure the suppressor, but if you make it fit tight enough, it shouldn't be necessary.
Correct orientation of the parts shown above, no supports needed. Use whatever material you like, I used eSun PA-CF.
Parts list:
End plate (Needs a tight fit around the barrel,+ 3x M3x10)
Rear chamber (3x M3x10)
"Flash hider" (M14x1 CCW, also needs a very tight fit)
Middle chamber (4x M3x20)
Insert (Needs a tight fit)
Outer shell
Note that you can't mount anything on the sides, or the lower 45° mlok holes. You want to mount a flashlight etc, it needs to go on the upper 45° holes. Grips etc on the bottom are fine.
More volume means better suppression, and I didn't want to make the suppressor any longer, so the first chamber goes back around the barrel. The size is roughly 42mmx200mm.
Use foam/scotch-brite/whatever on the inside. You can also add a layer of painters tape on the baffles and shoot a hole through. Keep in mind that this might affect accuracy, but its better for suppression.
Depending on your printer, some parts might need some grinding to make a tight fit.
There is an option for a M4 brass insert to secure the suppressor, but if you make it fit tight enough, it shouldn't be necessary.
Correct orientation of the parts shown above, no supports needed. Use whatever material you like, I used eSun PA-CF.
Parts list:
End plate (Needs a tight fit around the barrel,+ 3x M3x10)
Rear chamber (3x M3x10)
"Flash hider" (M14x1 CCW, also needs a very tight fit)
Middle chamber (4x M3x20)
Insert (Needs a tight fit)
Outer shell
Similar models
thingiverse
free
integrated suppresor for KJ Works MK 1 Ruger by DrakeElric
...iant. you will also have to drill and tap a new hole in the part and the receiver as the hole for fixing is in a different place.
thingiverse
free
MONSTERENERGY Suppressor! (airsoft) by Pinus0079
... want to put the sponge inside the monsterenergy-suppressor, remove the inner barrel.
the screw hole is a 14 mm left-hand thread.
thingiverse
free
Suppressor airsoft (not actually suppressing anything) by 3DSGN
...k. does not really work
does not have any treads its a press fit sollution so you can deside how far over the barrel you want it.
thingiverse
free
10 inch Airsoft Suppressor by jomarx
...erse
10 inch airsoft suppressor, although it doesn't have any 'suppressing' capabilities, use it as a barrel shroud.
thingiverse
free
Airsoft Suppressor Chamber by Sidenius
...tried to make it with chambers and here are my results.
its 30x30x19mm by default but you can scale them to your liking :) enjoy!
thingiverse
free
Fake suppressor for airsoft L96 by Myrmecoman
...bove the screw part (to make the suppressor grip the barrel better). then screw (4mm screw needed and a nut). it's installed.
thingiverse
free
Henry Front Sight by Crashin_Machines
...g it, the mag tube will be brought down so keep that in mind. files are included if you wanted to modify it to your own desires.
thingiverse
free
Pellet Gun Suppressor by Teubert1162
...r barrel. may need to run a drill bit through it to make sure there's enough clearance for the pellet. customize as you wish.
thingiverse
free
First Strike Mock Suppressor by FullPlasticAlchemist
...ock suppressor to work with a 9" first strike t8.1 barrel. it's a tight fit and stays on that way. no set screws needed.
thingiverse
free
Airsoft USP.45 Silencer/Suppressor by TherminalMirror
...t sure about that.
what you need:
2x m5 screws with nuts
note: this is a mock silencer, i does not suppress the sound in any way!
Mcmik3
thingiverse
free
Safariland QLS Wall Mount by mcmik3
...safariland qls wall mount by mcmik3
thingiverse
lets you mount your safariland qls holster almost anywhere. 4mm mounting holes.
thingiverse
free
Wolverine MTW Spade Grip by mcmik3
... threaded rod, around 300mm, cut to size
m8 lock nut
7pcs m4 threaded inserts, i used ruthex m4x8
mlok mounting screws & nuts
thingiverse
free
Surefire pressure switch mount for M-Lok V4 by lolikongpoi
...mount for m-lok v4 by lolikongpoi thingiverse remix from mcmik3 add additional structure to lock in m-lok mount. may...
Mtw
thingiverse
free
Skywing MTW-TD80K Bracket by rolfbartels
...thingiverse
this is a canister bracket for the mtw-td80k to fit the skywing can tunnels, i printed this with 100% infill and abs
thingiverse
free
BLTouch Mount for MTW Create by bgor
...e slots align with the holes in the x carriage plate where the ir sensor would attach.
designed for m3 screws; holes 12.5mm deep.
thingiverse
free
Wolverine MTW Maxx Hop-up spacer by Sniper_is_Silent
...acer by sniper_is_silent
thingiverse
the maxx hop-up chamber has terrible wobble in the wolverine mtw so i designed this spacer.
thingiverse
free
MTW Minimax adjustable Z-endstop by capro71
...u will need to add a 40mm m5 or possibly m4 button head hex bolt with a couple teflon locknuts and you're in business.
enjoy!
thingiverse
free
MTW Create Spool Holder
...tform). v1.75 is made to be an easier print than v1.7, but v1.75 might use more material. as of now, v1.7 and v1.75 are untested.
thingiverse
free
Easy bed levelers for MTW Minimax by Beerglut
...semble as shown in the assembly detail stl that i've also included. don't print this! then come back and post your pic.
thingiverse
free
Wolverine MTW Spade Grip by mcmik3
... threaded rod, around 300mm, cut to size
m8 lock nut
7pcs m4 threaded inserts, i used ruthex m4x8
mlok mounting screws & nuts
thingiverse
free
Blower Fan Duct for MTW Minimax by Beerglut
... reuse the screws from the original y end stop. you won't need those pesky teeny m2 nuts as it is designed to take a thread.
thingiverse
free
Fusematic Inductive sensor & fan mount by latrolobos
...leveling this bed. i remixed the fan holder from mtw to hold an inductive sensor. going to remix again...
Suppressor
turbosquid
$10
Suppressor
...turbosquid
royalty free 3d model suppressor for download as on turbosquid: 3d models for games, architecture, videos. (1218207)
turbosquid
$3
Suppressor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Suppressor Trak
...squid
royalty free 3d model suppressor trak for download as on turbosquid: 3d models for games, architecture, videos. (1395793)
turbosquid
$10
Suppressor Micro
...quid
royalty free 3d model suppressor micro for download as on turbosquid: 3d models for games, architecture, videos. (1380433)
turbosquid
$10
Suppressor Lunar
...quid
royalty free 3d model suppressor lunar for download as on turbosquid: 3d models for games, architecture, videos. (1380407)
turbosquid
$10
Suppressor Hornet
...uid
royalty free 3d model suppressor hornet for download as on turbosquid: 3d models for games, architecture, videos. (1380352)
turbosquid
$4
Pistol Suppressor
...
royalty free 3d model pistol suppressor for download as c4d on turbosquid: 3d models for games, architecture, videos. (1155814)
turbosquid
free
Futuristic Rifle with Suppressor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
Sniper with Suppressor, Scope and Laser
...sor, scope and laser for download as blend, dae, stl, and obj on turbosquid: 3d models for games, architecture, videos. (1549030)
turbosquid
$35
Riffle with Suppressor and Red Dot Sight
...iffle with suppressor and red dot sight for download as blend on turbosquid: 3d models for games, architecture, videos. (1548942)