Thingiverse
Mouthpiece Remover by Puglife
by Thingiverse
Last crawled date: 3 years, 1 month ago
A mouthpiece getting stuck is SOOOO annoying. Unfortunately, they cost $40 on Amazon! In preparation for the marching band season, I decided to make a cheap, 3D printed mouthpiece remover. This was made to work on trumpet mouthpiece, however it should work on most other small mouthpieces like french horn, mellophone, cornet, and fugal. In total this project cost $7 to make and 30 minutes to assemble. Total printing time was 5 hours at .1 mm with the Tevo Tornado.
How to remove a mouthpiece:
loosen the crown bolts at the bottom of the mouthpiece remover until the sliders can slide.
move the two sliders away from each other to make room form the mouthpiece.
turn the bottom wing nut on the threaded rod clockwise (bottom point of view), and alternate this process on both sides until the mouthpiece can be placed in with the sliders above the lip were the mouthpiece connects to the lead pipe.
move the sliders inwards to secure the base of the mouthpiece. Tighten the two crown bolts to lock the sliders in places.
alternate turning the top two wing nuts clockwise (top point of view) until the mouthpiece pops out. WARNING: They can really pop out quite aggressively, I'm not responsible if any mouthpiece gets dents by falling on the floor.
Here's a video of me using it:https://www.youtube.com/watch?v=AeP1htOAiFo
Materials:
All the supplies were found at Home Depot.
1/4 in threaded rod
1/4 in - 20 nylon lock nut (2 needed)
1/4 in - 20 nut (2 needed)
1/4 in - 20 wing nuts (4 needed)
number 8-32 x 3/8" wing/crown screw (2 needed)
number 8 metal washer (2 needed)
Assembly:
Print all the parts out (no supports required!)
Cut the threaded rod to an appropriate length (mine were 3.75 in long)
Insert the threaded rod into both the threaded holes in the top section of the mouthpiece remover to break away any lose plastic/defects in the print. Remove the rod afterwards.
At one end of each of the threaded rod, put on a lock nut. They can be twisted on part of the way by hand, but then you need to use a wrench and pliers to twist the nut until the end is flush with the rod.
Insert one of the rods with the nut into the bottom of the build. Then, put on that sides slider and hold it in with it's corresponding crown bolt and washer.
Insert the rod into the top section of the build. Use the wing nuts and regular nuts to help twist it on (see picture for nut setup)
Insert the other rod into the other whole, again put on its wing nuts and nut to twist it in.
Put on the other slider and its crown bolt and washer and you're done!
I designed this using fusion 360 and by looking at pictures of existing mouthpiece removers. If you enjoyed this project, a tip/like would be very much appreciated!
How to remove a mouthpiece:
loosen the crown bolts at the bottom of the mouthpiece remover until the sliders can slide.
move the two sliders away from each other to make room form the mouthpiece.
turn the bottom wing nut on the threaded rod clockwise (bottom point of view), and alternate this process on both sides until the mouthpiece can be placed in with the sliders above the lip were the mouthpiece connects to the lead pipe.
move the sliders inwards to secure the base of the mouthpiece. Tighten the two crown bolts to lock the sliders in places.
alternate turning the top two wing nuts clockwise (top point of view) until the mouthpiece pops out. WARNING: They can really pop out quite aggressively, I'm not responsible if any mouthpiece gets dents by falling on the floor.
Here's a video of me using it:https://www.youtube.com/watch?v=AeP1htOAiFo
Materials:
All the supplies were found at Home Depot.
1/4 in threaded rod
1/4 in - 20 nylon lock nut (2 needed)
1/4 in - 20 nut (2 needed)
1/4 in - 20 wing nuts (4 needed)
number 8-32 x 3/8" wing/crown screw (2 needed)
number 8 metal washer (2 needed)
Assembly:
Print all the parts out (no supports required!)
Cut the threaded rod to an appropriate length (mine were 3.75 in long)
Insert the threaded rod into both the threaded holes in the top section of the mouthpiece remover to break away any lose plastic/defects in the print. Remove the rod afterwards.
At one end of each of the threaded rod, put on a lock nut. They can be twisted on part of the way by hand, but then you need to use a wrench and pliers to twist the nut until the end is flush with the rod.
Insert one of the rods with the nut into the bottom of the build. Then, put on that sides slider and hold it in with it's corresponding crown bolt and washer.
Insert the rod into the top section of the build. Use the wing nuts and regular nuts to help twist it on (see picture for nut setup)
Insert the other rod into the other whole, again put on its wing nuts and nut to twist it in.
Put on the other slider and its crown bolt and washer and you're done!
I designed this using fusion 360 and by looking at pictures of existing mouthpiece removers. If you enjoyed this project, a tip/like would be very much appreciated!
Similar models
3dwarehouse
free
Bolt, Washer, Wing Nut, Spring, Threaded Insert and T-Nut - 1/4'
...rt and t-nut - 1/4'
3dwarehouse
bolt, washer, wing nut, spring, threaded insert and t-nut - 1/4' (drawn with sketchup 8)
3dwarehouse
free
1/2' bolt with washers and threaded nut
...hreaded nut
3dwarehouse
1/2' bolt (with threads) with washers and threaded nut. #12 #bolt #flat #lock #nut #threaded #washer
3dwarehouse
free
Threaded Rod - 1/4 - 20 x 1'
...threaded rod - 1/4 - 20 x 1'
3dwarehouse
1' threaded rod segment with washer and nut #threaded_rod_nut_bolt_washer
thingiverse
free
The qInch Project : Elbow Joint by sketchpunk
...nch neoprene washer
one 1 1/2 inch 1/4-20 bolt and 3 nuts.
whatever length bolt needed or threaded rod with nut or lock nuts.
3dwarehouse
free
Bolt 1/4' - 28 x 1.5'
...3dwarehouse
washers, lock washer, and nut included. ratings and feedback are appreciated. #bolt #lockwasher #nut #thread #washer
thingiverse
free
Improved Z Axis for Cyclone PCB Factory by xxreef
...a site where i'd like to add tutorial and similar stay tuned. www.mischianti.org update 01/02/2019: now you can download...
grabcad
free
1/4-20 Carriage and Hex bolts , washers, and nuts
...d hex bolts from 0.75 to 4.00 long with 1/4-20 thread form per uts standard. also includes hex nuts, nylock hex nuts and washer.
thingiverse
free
Adjustable leveling wedge (jack wedge) by Sekin
...on insert lock nut to prevent spinning of the rod on wrong side. the other side should be accompanied with a washer and wing nut.
thingiverse
free
Front Facing Filament Holder
...ecess in base. add another lock nut onto back of base to secure. you could also use a long enough hex bolt for easier tightening.
thingiverse
free
60ml syringe extruder by hegel
... x 1/4-20 hex nut
2 x 1/4-20 jam nuts
1 x 1/4 all thread approximately 6.5in length
1 x 1/4-20 philips or other driven screw head
Puglife
3d_export
$69
peugeot e-2008
...peugeot e-2008 3dexport peugeot e-2008 https://www.peugeot.es/gama/nuevo-peugeot-e-2008.html#puglife0 clean geometry light weight model, yet completely detailed for...
thingiverse
free
Low Poly Pig by Puglife
...low poly pig by puglife
thingiverse
a simple low-poly pig made in blender.
thingiverse
free
Dapple Dualies - Splatoon 2 by Puglife
... favorite weapons, so i thought i would make one to print. if you want it to be life size, put it at 300% scale.i hope you enjoy!
thingiverse
free
Splatoon Rainmaker by Puglife
... .1 mm layer height to help capture some of the details. also make sure to scale the model to an appropriate size in your slicer.
thingiverse
free
Gear Fidget Spinner by Puglife
... print settings.
parts to print:
1 gear spinner frame male
1 gear spinner frame female
4 fidget spinner gear
2 fidget spinner cap
thingiverse
free
Legend of Zelda Breath of the Wild - Bokoblin by Puglife
...roblems if your print settings are good. i would recommend a .1 mm layer height to help capture all of the details in this model.
thingiverse
free
Nintendo Switch - Charging Stand by Puglife
...
important:
2540% the scale in your slicer. it's trying to convert inches to mm when i export it, sorry for the inconvenience
thingiverse
free
Splatoon Weapon: Splash-O-Matic by Puglife
...dissolvable supports for a clean finish. acrylic paint is best for plastics if you intend to paint it. hope you enjoy the model!
thingiverse
free
Triangle Peg Board Game by Puglife
...tuck.
parts list:
1 peg board
14 pegs
if you print this, i would really appreciate it if you post a make of it, thanks and enjoy!
Mouthpiece
3d_export
$5
hookah mouthpiece
...hookah mouthpiece
3dexport
hookah mouthpiece that you can print on your 3d printer
3d_export
$19
Pipe wood with base capital 3D Model
...with base capital 3d model 3dexport pipe wood capital mouthpiece stove pipe wood with base capital 3d model imagebos...
3d_export
$12
Hookah 3D Model
...relaxation rest fire excitement extravagance intoxication frenzy hookah tobacco mouthpiece coals hookah 3d model bms3d 99517...
3d_ocean
$17
Hookah
...hookah 3docean coals excitement extravagance fire frenzy hookah intoxication mouthpiece relaxation rest smoke smoking tobacco the hookah scene, render...
3d_export
$20
alto saxophone
...of an alto saxophone with a detachable and rotatable mouthpiece and neck. everything is modeled down the last screw...
3d_export
$50
Trombone 3D Model
...perform jazz solo textures materials shiny realistic bass soprano mouthpiece marching trombone 3d model plutonius 27038...
thingiverse
free
Mouthpiece for pipe
...mouthpiece for pipe
thingiverse
mouthpiece for pipe
thingiverse
free
mouthpiece by thomoli
...mouthpiece by thomoli
thingiverse
parametric mouthpiece
thingiverse
free
trombone mouthpiece
...trombone mouthpiece
thingiverse
working trombone mouthpiece that says bone on it
thingiverse
free
BOQUILLA / MOUTHPIECE by jaimecastegym18
...boquilla / mouthpiece by jaimecastegym18
thingiverse
boquilla / mouthpiece
Remover
turbosquid
$15
Staple Remover
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Staple Remover
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$1
Staple Remover
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$25
Staple Remover 3D Model
...remover office supplies pull desk paper remove workplace school work desktop vray
staple remover 3d model plutonius 7699 3dexport
turbosquid
$28
Removable Wall Hatch
... 3d model removable wall hatch for download as , fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1670326)
3d_export
$15
Staple Remover 3D Model
... desktop paper accessories household tool desk workplace instrument equipment pull
staple remover 3d model firdz3d 90012 3dexport
3ddd
free
Missed Maps Remover
...
3ddd
missed maps remover
скрипт находит потерянные карты в файле и позволяет удалить их или открыть в окне редактора материалов.
turbosquid
$29
Eye remover
...bosquid
royalty free 3d model eyeremover for download as 3dm on turbosquid: 3d models for games, architecture, videos. (1695439)
3ddd
$1
Remove Note Track
...аем скрипт чтобы удалить нулевые треки,которые грузят систему при сохранении и файл начинает сохраняться снова нормально и быстро
3d_export
$6
Gas dust removal bag filter
...gas dust removal bag filter
3dexport
gas dust removal, bag filter