Thingiverse
Motor Mount for SSS 4092 Motor by Daniel_Blake
by Thingiverse
Last crawled date: 3 years, 4 months ago
The Motor mount included in this rc boat model would not hold/fit the needs for myself. This was then created to allow me to fit a SSS 4092 motor in to the boat.
This includes two parts. Front end and rear end of the mount.
Front is used to hold the motor inplace. so it does not shift left or right.
Rear is there to hold the motor in tight. as this uses a clasping method. This will need an M3 nut and nylon nut. With washers to keep the screw and nut from damaging the mount.
When installing. Mount the front end of the mount to the motor and move it to the point where there is little to no slack with the drive train.
Then attach the rear end mount. tighten it up and place in the slot of the boat. This essentually means the motor is in place.
But best to use CA Glue on the rear mount against the hull of the boat.
The way this is designed will allow the user to remove the motor freely by untightening the rear clasp and sliding the motor forward and then up. But also have the regidity to hold such a monster of a motor!!.
This includes two parts. Front end and rear end of the mount.
Front is used to hold the motor inplace. so it does not shift left or right.
Rear is there to hold the motor in tight. as this uses a clasping method. This will need an M3 nut and nylon nut. With washers to keep the screw and nut from damaging the mount.
When installing. Mount the front end of the mount to the motor and move it to the point where there is little to no slack with the drive train.
Then attach the rear end mount. tighten it up and place in the slot of the boat. This essentually means the motor is in place.
But best to use CA Glue on the rear mount against the hull of the boat.
The way this is designed will allow the user to remove the motor freely by untightening the rear clasp and sliding the motor forward and then up. But also have the regidity to hold such a monster of a motor!!.
Similar models
thingiverse
free
Boat Canopy Tube Supports by 3geeks
...g straps. we used these ends to create a rigid rear support so the bimini top could be folded back without dropping to the rear.
thingiverse
free
Mini z buggy MB-010 rear mount plates for rocket 1410 motor by synco
...ed to fit 1410 brushless motors, original front mount plate is used without modification.
sizes 2 and 3 like the original plates.
thingiverse
free
Zippa 250 Motor Mounts by ixlix
...images, so the inside clearance for the arm is a perfect square. the mounts are the same left to right so just print two of each.
thingiverse
free
Z Axis Adjsutable Motor Mount (one-sided) by jprizzle
...is for a second z motor on the opposite side of the printer.
required hardware:
4 m3 x 6mm screws
2 m4 x 10mm screws
2 m4 t-nuts
thingiverse
free
Telescope Worm Drive by mcdewey
...ks hold skate board bearings. the fit for the bearings is a little lose but the nuts hold everything in place so all is good ;-).
thingiverse
free
E3d upgrade for Wombot Exllis by Paul3163
...y screws from jaycar.
design files are included
40mm fan adaptor was from the link belowhttps://www.thingiverse.com/thing:2572641
thingiverse
free
Motor Retainer Set for 29mm Rocket Motors by JMillsCabrilloHS
...to the aft end of the motor mount tube, similar to an estes retainer. easier than using nuts &...
thingiverse
free
Anet A8 Rear Acrylic sides, remade by Goodwynn89
...ylic frame, these are the ends of the rear most part that holds the all thread rods, the y motor mount, y end stop, and what not
thingiverse
free
Great Planes Motor Mount PBY Catalina by GalaxyClass
... 180 degrees before printing. (need to figure out how to rotate my exports)
i did this in cubify invent. ask for the .fun file.
thingiverse
free
Rear Skid Guard for Traxxas E-Revo by DZeek
...rd for traxxas e-revo that holds rear pins in place. will need to print with supports for the two upper front screw hole mounts.
Sss
thingiverse
free
sss by kchumbo35
...sss by kchumbo35
thingiverse
thingiverse
free
sss by isaacpuder6
...sss by isaacpuder6
thingiverse
s
thingiverse
free
sss by vvvccd
...sss by vvvccd
thingiverse
ssss
thingiverse
free
sss by yanggensnake
...sss by yanggensnake
thingiverse
sssssss
gawg
wahwaaawawww
thingiverse
free
SSS Logo (rough) by probesport
...sss logo (rough) by probesport
thingiverse
this is just a quick render of my schafer speed shop logo. nobody needs this.
thingiverse
free
SSS Plaque for filament by LoZa
...sss plaque for filament by loza
thingiverse
plaque for filament, you can identify very easy the filament inside de spool holder
thingiverse
free
Skydivers Supporting Sobriety (SSS) Coin by markrickert81
...porting sobriety facebook group.
print settings
printer: any
rafts: doesn't matter
supports: no
resolution: 0.2mm
infill: any
thingiverse
free
Replacement pins for Siedle (SSS) Intercom system HT-351-0 B by Timothy_McPrint
...y siedle (sss). name of the system: ht-351-0 b.
this system is over 35 years old now, and the pins are very often already broken.
thingiverse
free
SSS - Saubermacher Scan Session by nischi
...r firma saubermacher. mein netter kollege hannes bat mit da 2 personen zu scannen - es wurden dann aber in summe doch etwas mehr.
Blake
thingiverse
free
Blake Moore
...blake moore
thingiverse
....
thingiverse
free
Nametag Blake
...nametag blake
thingiverse
adgrddrg
thingiverse
free
blake by davabran
...blake by davabran
thingiverse
scan of a bust
thingiverse
free
Flexbot Blake by bbutler
...flexbot blake by bbutler
thingiverse
this is a design for a flexbot.
thingiverse
free
Blake Keychain by Argo118
... freedom20a blake_keychain. the model was cleaned up and flattened in areas that were not flat and changed the loop to a circle.
thingiverse
free
Blake's 7 The London by Tobz
...blake's 7 the london by tobz
thingiverse
the "london" prison transport from blake's 7 , found on sketchup
thingiverse
free
Howdahs for Blake
...wdahs for blake
thingiverse
for riding atop elephant. scaled for a schleich elephant.
i printed 4 serpents and glued to base.
thingiverse
free
Blakes Snowflake by blakemoss1234
...blakes snowflake by blakemoss1234
thingiverse
my snowflake design for the 3d printer challenge.
thingiverse
free
William Blake - Plates Litho/ Mural by nuggyblake
...william blake - plates litho/ mural by nuggyblake
thingiverse
william blake - plate litho/ mural
thingiverse
free
William Blake - Work The last Judgement by nuggyblake
...william blake - work the last judgement by nuggyblake
thingiverse
william blake litho/ mural from plate work
Daniel
thingiverse
free
Daniel-snowman by kpcampbell07
...daniel-snowman by kpcampbell07
thingiverse
created by daniel
thingiverse
free
Daniels Logo by wreynolds75
...daniels logo by wreynolds75
thingiverse
logo for daniels handmade
thingiverse
free
Daniel Tree by HuskieCAD
...daniel tree by huskiecad
thingiverse
christmas tree by daniel
thingiverse
free
Jack Daniels Mug
...jack daniels mug
thingiverse
i created a mug with the jack daniels logo on
thingiverse
free
Daniel by schmidjon
...daniel by schmidjon
thingiverse
scan with structure.io
thingiverse
free
Dear Daniel by christophe94
...kitty.
original source:https://b2b.partcommunity.com/community/partcloud/index?route=part&name=dear+daniel&model_id=54577
thingiverse
free
Daniel by thoxbui
...daniel by thoxbui
thingiverse
scanned with kinect and skanect
thingiverse
free
Scarpetta Neonato "Daniel" by MiguelBi
...scarpetta neonato "daniel" by miguelbi
thingiverse
daniel scarpette
thingiverse
free
Dear Daniel by Dape
...itty.
original source:
https://b2b.partcommunity.com/community/partcloud/index?route=part&name=dear+daniel&model_id=54577
thingiverse
free
ashtray jack daniels by balkaii
...ashtray jack daniels by balkaii
thingiverse
ashtray jack daniel's whisky
Motor
thingiverse
free
Motor test
...motor test
thingiverse
motor stand for test rc motors
thingiverse
free
Motor Halter Conrad Motor by Kortie
...motor halter conrad motor by kortie
thingiverse
motor halterung für tamiya trucks 1:14 in verbindung conrad motor
thingiverse
free
motor mount for 550 brushed motor by lijingwei
...motor mount for 550 brushed motor by lijingwei
thingiverse
motor mount for 550 brushed motor
thingiverse
free
Motor Guard for 2306 Motors by Simongotnews
...motor guard for 2306 motors by simongotnews
thingiverse
should work with the most common motors in 2306 standarts.
thingiverse
free
Motor mount
...motor mount
thingiverse
motor mount
thingiverse
free
ZMR250 Motor protector for 1806 Motor by king_draki
...otector for 1806 motor by king_draki
thingiverse
nice an light motor protector for 1806 motors.
m2.5 max.
12 -16 mm motor mount.
thingiverse
free
Motor Mounts for YoYo Motors by drmcland
...line following and or semi autonomous robots using these motors.
the image above is the bottom of a self balancing robot.
enjoy
thingiverse
free
Motor base
...motor base
thingiverse
base do motor regulavel
thingiverse
free
Motor Estrella
...motor estrella
thingiverse
motor estrella 6 cilindros.
thingiverse
free
Motor fitting
...motor fitting
thingiverse
wrap's around motor
Mount
thingiverse
free
Pen Mount on BLTouch mount by jetspot
...pen mount on bltouch mount by jetspot
thingiverse
pen mount on bltouch mount
thingiverse
free
RAM Mount, Mount by seanmclean
...ram mount, mount by seanmclean
thingiverse
bridging plate to attach ram mount to yamaha 242, for chartplotter placement.
thingiverse
free
Mount for mount for Garmin GPS by GNOBLIN
...you can use this mount for prevent rotation simple mount around hendelbars.
d handelbar 31.8mm
use m3 screw and din 16903 plug.
thingiverse
free
Permanent mount for Modular Mounting System by WIR14
...permanent mount for modular mounting system by wir14
thingiverse
permanent mount for modular mounting system.
thingiverse
free
Gopro Mount and antenna mount by SuperYoyo
...gopro mount and antenna mount by superyoyo
thingiverse
cut the carbon platform to pass the gopro mount and enjoy !
thingiverse
free
Hexagon Mount for 50mm Mount (Sparkcube) by Draman
...for 50mm mount (sparkcube) by draman
thingiverse
hexagon mount remix from skimmys hotend-mount for sparkcube or other 50mm-mount
thingiverse
free
mount by gixster
...mount by gixster
thingiverse
custom mount
thingiverse
free
Mount by Matrxi999
...mount by matrxi999
thingiverse
shelf mount
thingiverse
free
Motor mount
...motor mount
thingiverse
motor mount
thingiverse
free
GoPro Mount
...gopro mount
thingiverse
gopro mount