Thingiverse
Mosquito by Diymik
by Thingiverse
Last crawled date: 3 years ago
ATTENTION: Maiden flight shows the thrust angle is wrong, will update soon.
DeHavilland Mosquito.
Original 3d model: https://grabcad.com/library/de-havilland-dh-98-mosquito-1
Wingspan- 600mm
Weight of printed parts- 310g
Work in progress, if you print it and fly it, give some feedback, and suggestions for improvements.
I designed it to use my old racing quadcopter parts.
This uses 2205 to 2306 size motors. These motors typically will deliver 1kg+ thrust each. So it should have unlimited vertical flight. It will take 5-6 inch props.
It is designed to fit a 1300-1500mah 4 cell battery, 3 or 4 9g servos (rudder optional) and there is a nose option to fit a Hs1177 style fpv camera.
You will need 6mm carbon tube for the wing spars, and fuselage spine. An ice cream stick ( we call it a paddlepop stick, in Australia) for the tailplanes.
Space inside is tight, and you may have to get creative to fit an fpv antenna in there.
The wing profile and area is straight from the original model, and is not optimised for RC models, so it might not have much lift. Depending on how well it goes, i may do another wing at a later stage.
This is a difficult print and you will need to have your printer calibrated. Advanced knowledge of your slicer settings is essential. Overhangs and support structures have been minimised, but you must follow the printing instructions for it to work.
Recommended printer size: 200x200x180. Might just fit on 180x180x120.
You can print the elevator and aileron hinges with flexible filament. If you use something else for the hinges, you will need to fill the gaps with something, im sure you can figure it out.
Option parts:
noseHS1177 will fit an fpv camera the same size as a HS1177.
Shortcowl allows you to grip the motor to change props.
Motormountthick has a thicker base, and is for mounting the motor with no motor cowl.
Covers for the elevator and rudder servos have a deep version, depends on your servo which will fit best.
DeHavilland Mosquito.
Original 3d model: https://grabcad.com/library/de-havilland-dh-98-mosquito-1
Wingspan- 600mm
Weight of printed parts- 310g
Work in progress, if you print it and fly it, give some feedback, and suggestions for improvements.
I designed it to use my old racing quadcopter parts.
This uses 2205 to 2306 size motors. These motors typically will deliver 1kg+ thrust each. So it should have unlimited vertical flight. It will take 5-6 inch props.
It is designed to fit a 1300-1500mah 4 cell battery, 3 or 4 9g servos (rudder optional) and there is a nose option to fit a Hs1177 style fpv camera.
You will need 6mm carbon tube for the wing spars, and fuselage spine. An ice cream stick ( we call it a paddlepop stick, in Australia) for the tailplanes.
Space inside is tight, and you may have to get creative to fit an fpv antenna in there.
The wing profile and area is straight from the original model, and is not optimised for RC models, so it might not have much lift. Depending on how well it goes, i may do another wing at a later stage.
This is a difficult print and you will need to have your printer calibrated. Advanced knowledge of your slicer settings is essential. Overhangs and support structures have been minimised, but you must follow the printing instructions for it to work.
Recommended printer size: 200x200x180. Might just fit on 180x180x120.
You can print the elevator and aileron hinges with flexible filament. If you use something else for the hinges, you will need to fill the gaps with something, im sure you can figure it out.
Option parts:
noseHS1177 will fit an fpv camera the same size as a HS1177.
Shortcowl allows you to grip the motor to change props.
Motormountthick has a thicker base, and is for mounting the motor with no motor cowl.
Covers for the elevator and rudder servos have a deep version, depends on your servo which will fit best.
Similar models
thingiverse
free
LED Search Light by Kojoe
...small piece mirror
arduino pro
some electronics component
you can make a fitting that takes the 23mm hole to the size you require
thingiverse
free
FPV Pan Mount for Insta360 Go2 by t4obrien
...o knife to chamfer the opening a little after printing. bolt it on and you're ready to rock!
post a make when you make yours!
thingiverse
free
GoPro Session and Foxeer HS1177 dual camera mount
...winch servo. i can not guarantee this will fit any servo mount you might have.
print this at your own risk, you have been warned.
thingiverse
free
HS1177/RunCam FPV Camera to 9g Servo Mount (metal and plastic gears) by Painless360
...s and use acetone to soften the plastic for mounting to the servo to make sure the teeth are engaged to support.
happy printing!
thingiverse
free
400 mm Drone FPV Racing by Javi17
...king for the camera mount for an hs1177
if you have any question ask me and i will answer as soon as posible.
i hope you like it.
thingiverse
free
Circular corner connector by Thralil
...ending on precision of your printer.
i have also included test rings so you can test the fit without needing to print whole part.
thingiverse
free
Walkera FPV Lens Cap by Stevengineer
...veryone's print settings are different, you will likely have to re-size it very slightly to get a good fit from your printer,
thingiverse
free
30.5mm x 30.5mm FPV Pod by baril792
...ike). you might need to chase some of the holes with a drill bit depending upon if your printer tends of over-extrude like mine.
thingiverse
free
Toothbrush holder by mcotton
...rse
i made this in two pieces to make printing easier. depending on your printer it might need a little glue to stick together.
thingiverse
free
FPV BiCopter by DzikuVx
...fpv bicopter by dzikuvx thingiverse bicopter frame. flight concept similar to avatar copter. you will need: 4 10x4x3 bearings...
Diymik
thingiverse
free
Handything V2 by Diymik
... v2 by diymik
thingiverse
version 2 of the handything. its a lot smaller, more suitable for some pens and maybe some paperclips.
thingiverse
free
Flight controller soldering jig by Diymik
...flight controller soldering jig by diymik
thingiverse
soldering jig for standard size (36x36mm) flight controllers.
thingiverse
free
Handything by Diymik
... handything v3 is the biggest and most practical.http://www.thingiverse.com/thing:1751022http://www.thingiverse.com/thing:1752414
thingiverse
free
Handything V3 by Diymik
...or building or modifying racing quadcopters.
or for holding my 3d printing stuff.
it holds some tools and some screws and things.
thingiverse
free
Frsky L9R enclosure by Diymik
...ue this box in your model, and snap in the l9r.
no glue on the l9r.
allows you to access all the ports and remove the l9r easily.
thingiverse
free
FRSKY antenna mount by Diymik
...ingiverse
super simple antenna mount for frsky.
45 deg.
took me about 5 mins to design, could easily be improved. (hint hint) ;)
thingiverse
free
vortex generator by Diymik
...ors for full size light aircraft.
"vortexgen" has a 0.5mm base.
added "vortexthin" file. it has a 0.3mm base.
thingiverse
free
Bungee tow hook by Diymik
...kid so it wont dig in when landing.
use tape to spread the load, so it wont rip a hole in the bottom of your fuselage. see photo.
thingiverse
free
Eagle Tree Vector mount by Diymik
...and your vector can clip in.
keeps the glue off the vector, tight fit, so it wont wobble.
has clearance for all cables and plugs.
thingiverse
free
XT60 cap by Diymik
... easy and a lip to grab so you can pull it off the plug. prints real easy. yes i thought it through, this one works for everyone.
Mosquito
design_connected
$16
Mosquito
...mosquito
designconnected
rex kralj mosquito computer generated 3d model. designed by kralj, niko.
3d_export
$5
Mosquito
...of some place that is destroyed or abandoned long ago. with such models the application would top the charts and prove its worth.
turbosquid
$100
Mosquito
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$69
Mosquito
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$22
mosquito
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Mosquito
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$15
mosquito
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$3
Mosquito
... model mosquito for download as 3ds, obj, fbx, blend, and dae on turbosquid: 3d models for games, architecture, videos. (1311331)
3d_export
$25
mosquito
...mosquito
3dexport
simple rendering of the scene file
3d_export
$10
Mosquito 3D Model
...mosquito 3d model
3dexport
mosquito insect bug hexapod flyer
mosquito 3d model def 19400 3dexport