Thingiverse
Micro 105 FPV Quadcopter - 8.5mm Motors, Micro Scisky by punkkills
by Thingiverse
Last crawled date: 3 years ago
This frame was inspired by the FireFlo V2 and the Alpine Drones Micro H. My goals were to keep it crash resistant, light weight and offer good protection for onboard gear.
It measures ~105mm. The V1 frame weighs ~10g and the V2 frame weighs ~8g when printed in PLA. My full build (currently V2 base and V1 top) weighs ~38g without the battery. It is designed around 8.5mm motors and the Micro Scisky flight controller. The camera mount is angled up 13 degrees to accommodate fast forward flight.
Build Instructions
See the full build instructions on instructables.
Base Setup
Flight Controller: You need a Flight Controller with a receiver that matches your radio. I list radio options for the different protocols below.
Eachine F3 FrSky
Eachine F3 FlySky
Eachine F3 DSM2
FlySky Micro Scisky
FrSky Micro Scisky
DSMX/DSM2 Micro Scisky. You might need to remove the motor plugs from this one in order to fit inside the frame.
Motors: Hubsan X4 H107c 8.5mm Motors
Battery: I use a mix of a few batteries. 380mAh Hubsan, 500mAh Hubsan and 300mAh Nano-Techs CAUTION: When using the Nano-Techs, make sure the battery polarity is correct. I have had to switch the connector position on these.
Props: I am currently using Ladybird props. They hold up a lot better than the Hubsan props.
Battery Pigtail: I cut one of the leads off of a charging adapter.
Nylon Hardware: M3 nylon nuts and machine screws. I used the 20mm machine screws and cut them to size after attaching to the frame.
Printable Standoff And Clip: As an alternative to using nylon hardware, navyblueboss made a very nice pin and clip set. I have not yet printed a set of these but they look great.
JST SH Connector: A JST SH connector can be used to get get a 5v supply for fpv gear straight from the Scisky. CAUTION: I managed to fry the power supply on one of my Scisky boards. Other users have reported the same when using the FC to power FPV gear. Another option is to use straight battery power or a voltage regulator from battery for VTX and camera.
All in One FPV Gear
There are a few new options for an all in one FPV setup. You can connect these straight to battery power and don't need a voltage regulator. These camera and video transmitter modules can be used with the v4 frame. Here are a few options that I have tested with.
FX798T
FX797T
DIY FPV Gear
These components will allow you to build the FPV setup yourself. These components are for v1, v2, and v3 frames.
VTX: FX758-2 5.8G 200mW Video Transmitter
Antenna: I used the inner wire from the coaxial cable of a broken clover leaf antenna. I used the default frequency on the FX758-2 which is 5865. After soldering the wire on, I cut the antenna to 12.8mm which is the quarter wavelength of that frequency
Camera: 170 Degree Wide Angle Camera
5v Step-Up Voltage Regulator: Use a pololu 5v step-up instead of the JST SH connector to avoid burning up the voltage regulator on the Scisky.
Radio Options
You need a radio that matches the protocol of your FC. Here are some options for a few protocols.
FlySky
FlySky FS-i6
FlySky FS-i6X
FrSky
Taranis Plus
Taranis QX7
DSM2/DSMX
Spektrum DX6i
Spektrum DX5e
FsFly T-Six
Video Options
Eachine EV800 Goggles - These are inexpensive goggles that can double as a standalone screen. These would make a good pair of starter goggles.
Fatshark Dominator V3 Goggles + Receiver Module
Alternate Electronics
People have had success transplanting the flight controller and motors from a Hubsan X4 H107C. Going this route, you would get motors, flight controller, a battery, a radio and a set of props for relatively cheap. You could then add FPV with a camera, VTX and a voltage regulator. I have not tried this route yet, but plan to build one soon for a friend. I will post my results when I do.
Updates
1/9/2016 - Added bottom-v2-experimental. I was able to reduce the weight of the bottom of the frame to ~5.5g. This saves ~1.5g from v1. I don't think the frame durability will be affected much.
1/10/2016 - Added top-v2-experimental. I was able to reduce the weight of the top of the frame to ~2.3g. This save ~0.5g from v1. The v2 top and bottom combined should be ~8g when printed in PLA. Both the v2 top and bottom will feel a bit flexy separately, but once they are connected the quad will feel solid but still allow some give in crashes. I recommend using M3 nylon hardware to secure the pieces together. I do not anticipate the v2 top compromising durability in any way. NOTE: I have printed, but not flown with this top. My camera is hot glued to the v1 top so I will need to find some time to make the switch.
1/11/2016 - Added top-v2-no-cam-experimental. I've been doing some indoor LOS flying and wanted to see how it preformed without the FPV gear. Wow, there is a lot of pop.
1/16/2016 - Added top-v2-cam-down-7. This points the camera down 7 degrees. In order to clear the base plate, I had to push the camera forward just a bit and I made the standoffs of cam-down 1mm taller so the camera does not extend below the bottom plate. I also removed the word "experimental" from v2 filenames.
5/9/2016 - Added bottom-v3. This version should be much stronger than v2 but it weighs only ~0.2g more. I was able to increase the thickness of the arms while saving some weight with a few other modifications. I also added some relief to the back to make it easier to plug a USB cable into the Scisky.
7/25/2016 - Added v4 top and bottom which allow for all in one FPV modules. The bottom has hooks for an underslung battery and the top has a recessed seat for the FPV gear. I also added a 7mm version of the v4 bottom. I did not test the 7mm version as I don't have any 7mm motors. Please let me know how it works if you use this frame.
Videos
https://youtu.be/qZ-qDsXewZI
It measures ~105mm. The V1 frame weighs ~10g and the V2 frame weighs ~8g when printed in PLA. My full build (currently V2 base and V1 top) weighs ~38g without the battery. It is designed around 8.5mm motors and the Micro Scisky flight controller. The camera mount is angled up 13 degrees to accommodate fast forward flight.
Build Instructions
See the full build instructions on instructables.
Base Setup
Flight Controller: You need a Flight Controller with a receiver that matches your radio. I list radio options for the different protocols below.
Eachine F3 FrSky
Eachine F3 FlySky
Eachine F3 DSM2
FlySky Micro Scisky
FrSky Micro Scisky
DSMX/DSM2 Micro Scisky. You might need to remove the motor plugs from this one in order to fit inside the frame.
Motors: Hubsan X4 H107c 8.5mm Motors
Battery: I use a mix of a few batteries. 380mAh Hubsan, 500mAh Hubsan and 300mAh Nano-Techs CAUTION: When using the Nano-Techs, make sure the battery polarity is correct. I have had to switch the connector position on these.
Props: I am currently using Ladybird props. They hold up a lot better than the Hubsan props.
Battery Pigtail: I cut one of the leads off of a charging adapter.
Nylon Hardware: M3 nylon nuts and machine screws. I used the 20mm machine screws and cut them to size after attaching to the frame.
Printable Standoff And Clip: As an alternative to using nylon hardware, navyblueboss made a very nice pin and clip set. I have not yet printed a set of these but they look great.
JST SH Connector: A JST SH connector can be used to get get a 5v supply for fpv gear straight from the Scisky. CAUTION: I managed to fry the power supply on one of my Scisky boards. Other users have reported the same when using the FC to power FPV gear. Another option is to use straight battery power or a voltage regulator from battery for VTX and camera.
All in One FPV Gear
There are a few new options for an all in one FPV setup. You can connect these straight to battery power and don't need a voltage regulator. These camera and video transmitter modules can be used with the v4 frame. Here are a few options that I have tested with.
FX798T
FX797T
DIY FPV Gear
These components will allow you to build the FPV setup yourself. These components are for v1, v2, and v3 frames.
VTX: FX758-2 5.8G 200mW Video Transmitter
Antenna: I used the inner wire from the coaxial cable of a broken clover leaf antenna. I used the default frequency on the FX758-2 which is 5865. After soldering the wire on, I cut the antenna to 12.8mm which is the quarter wavelength of that frequency
Camera: 170 Degree Wide Angle Camera
5v Step-Up Voltage Regulator: Use a pololu 5v step-up instead of the JST SH connector to avoid burning up the voltage regulator on the Scisky.
Radio Options
You need a radio that matches the protocol of your FC. Here are some options for a few protocols.
FlySky
FlySky FS-i6
FlySky FS-i6X
FrSky
Taranis Plus
Taranis QX7
DSM2/DSMX
Spektrum DX6i
Spektrum DX5e
FsFly T-Six
Video Options
Eachine EV800 Goggles - These are inexpensive goggles that can double as a standalone screen. These would make a good pair of starter goggles.
Fatshark Dominator V3 Goggles + Receiver Module
Alternate Electronics
People have had success transplanting the flight controller and motors from a Hubsan X4 H107C. Going this route, you would get motors, flight controller, a battery, a radio and a set of props for relatively cheap. You could then add FPV with a camera, VTX and a voltage regulator. I have not tried this route yet, but plan to build one soon for a friend. I will post my results when I do.
Updates
1/9/2016 - Added bottom-v2-experimental. I was able to reduce the weight of the bottom of the frame to ~5.5g. This saves ~1.5g from v1. I don't think the frame durability will be affected much.
1/10/2016 - Added top-v2-experimental. I was able to reduce the weight of the top of the frame to ~2.3g. This save ~0.5g from v1. The v2 top and bottom combined should be ~8g when printed in PLA. Both the v2 top and bottom will feel a bit flexy separately, but once they are connected the quad will feel solid but still allow some give in crashes. I recommend using M3 nylon hardware to secure the pieces together. I do not anticipate the v2 top compromising durability in any way. NOTE: I have printed, but not flown with this top. My camera is hot glued to the v1 top so I will need to find some time to make the switch.
1/11/2016 - Added top-v2-no-cam-experimental. I've been doing some indoor LOS flying and wanted to see how it preformed without the FPV gear. Wow, there is a lot of pop.
1/16/2016 - Added top-v2-cam-down-7. This points the camera down 7 degrees. In order to clear the base plate, I had to push the camera forward just a bit and I made the standoffs of cam-down 1mm taller so the camera does not extend below the bottom plate. I also removed the word "experimental" from v2 filenames.
5/9/2016 - Added bottom-v3. This version should be much stronger than v2 but it weighs only ~0.2g more. I was able to increase the thickness of the arms while saving some weight with a few other modifications. I also added some relief to the back to make it easier to plug a USB cable into the Scisky.
7/25/2016 - Added v4 top and bottom which allow for all in one FPV modules. The bottom has hooks for an underslung battery and the top has a recessed seat for the FPV gear. I also added a 7mm version of the v4 bottom. I did not test the 7mm version as I don't have any 7mm motors. Please let me know how it works if you use this frame.
Videos
https://youtu.be/qZ-qDsXewZI
Similar models
thingiverse
free
Pilotgeek X60 Micro V2 - 85mm FPV Quadcopter for Scisky by Pilotgeek
...t the proper height and don't wobble.
-removed frame weight by making arms hollow and reducing thickness in strategic places.
thingiverse
free
Mini FPV Drone "BILBY" by jij83
....
-props: props for hubsan x4 (55mm)
radio controler:
-flysky fs-t6
-flysky fs-i6
or equivalent..
website:
www.vaptor-studio.tech
thingiverse
free
Micro Scisky FPV Quad by gibo
...d based on naze32 for multirotor)
motors: 8520 coreless motors.
prop: 75mm (0.97motor shaft id).
battery: 3.7 850mah 1s battery
thingiverse
free
Toad 110 Remix - AIO FPV (Brushed 8.5mm Motors) by wiretap
...degree incline on the lower deck for a cam+vtx similar to the eachine tx02. -- added a slot on...
thingiverse
free
Micro FPV Quadcopter 125 | 8.5mm motors and Micro Scisky by phiba
....8 ghz antenna
5.8 ghz receiver equipment
foam rubber, for bottom of quadcopter and camera (see pictures) in case of hard crashes
thingiverse
free
micro fpv drone 8520 90mm by v-cu
...battery, flysky fs-a8s receiver
to put the motors preheat the plastic with hot air and put it in
edit
i added v2 stronger version
thingiverse
free
The Flying Squirrel Micro QuadCopter by mojobromley
...0mm coreless motor
nano qx flight controller
hubsan 380 mah battery (also use 1s nano-tech 750mah)
https://youtu.be/zivhlrf_psg
thingiverse
free
Remix for Micro 105 FPV Quadcopter - 8.5mm Motors, Micro Scisky by t4b_
... a version to mount the mini cmos fpv cam 0.008lux for night flights
get the frame from: http://www.thingiverse.com/thing:1221911
thingiverse
free
Frog 100 - Micro FPV Quad - (8.5mm Hubsan X4 Motors, CC3D) by charlesgershom
... nimble (for flips etc).
would also work nice as a transplant frame for a hubsan x4 if you wanted to make a cheap custom fpv quad
thingiverse
free
Airwave - Micro FPV Quadcopter frame for Micro Scisky, 820 motors and FX797T by ivanwyc
...of 4 (2 cw + 2 ccw) cl-0820-15 or similar ones without the 1.25mm picoblade connector and unknown rpmbattery:...
Punkkills
thingiverse
free
TPU Esc Protection by punkkills
... is much lighter than using full esc shields.
for more quadcopter and fpv content, check out my blog at http://fpvobsession.com/!
thingiverse
free
Landing gear for Punkkills Micro 105 FPV Quadcopter by theTESTA
...round. no support nedeed.
the quadcopter's frame is not mine, you can find it here: https://www.thingiverse.com/thing:1221911
thingiverse
free
Screw replacement for Punkkills Micro 105 FPV Quadcopter by navyblueboss
... allready got that..
and as always: please share a picture or leave a comment after you printed this part, really appreciate it!
thingiverse
free
Landing Pin Replacement for Punkkills Micro 105 FPV Quadcopter by rsheldiii
...e pins a bit to get some ground clearance for the battery. note that you'll probably have to rotate the battery to use these!
thingiverse
free
Horizontal Antenna Mount by punkkills
...e. hopefully this will be a good compromise.
for more quadcopter and fpv content, check out my blog at http://fpvobsession.com/!
thingiverse
free
Hubsan x4 flight board mount for Punkkills' Micro 105 FPV Quadcopter by h3lpless
...screw will go through the mount and into the frame.
v1 and v2 have a 1mm thick bottom, v3 has a .6mm bottom with .4mm stand offs.
thingiverse
free
Hubsan x4 105mm FPV Quadcopter (Based off punkkills' Micro 105 FPV) by h3lpless
...nkkills, you may use nylon nuts and machine screws.
personally i have only used the printable screw replacements by navyblueboss.
thingiverse
free
Quadcopter Landing Skid - QAV210 by punkkills
...ended up using the large captive nut version.
for more quadcopter and fpv content, check out my blog at http://fpvobsession.com/!
thingiverse
free
HyperLite EVO Back Washer With Antenna Holder by punkkills
...ince using these.
print in tpu.
for more evo and quad stuff, check out my other things and blog over at http://fpvobsession.com/.
thingiverse
free
HyperLite EVO VTX Sling by punkkills
...og at http://fpvobsession.com/!
if you don't have a printer you can purchase this in a variety of colors from pb3d creations.
Scisky
thingiverse
free
Micro Scisky Board by kolergy
...micro scisky board by kolergy
thingiverse
open scad model of the naze32 based micro scisky board
thingiverse
free
Micro Scisky FPV Quad by gibo
...d based on naze32 for multirotor)
motors: 8520 coreless motors.
prop: 75mm (0.97motor shaft id).
battery: 3.7 850mah 1s battery
thingiverse
free
Scisky plate for Rolling Spider by magictex
...ix a scisky flight controller on a parrot rolling spider frame.
for mode details, please visit www.texfpv.com (in french, sorry).
thingiverse
free
110 quad 8.5 scisky board by hkrug
...0 quad 8.5 scisky board by hkrug
thingiverse
simple frame to hold 8.5 brushed motors and scisky/quanum pico fc. weighs about 5g.
thingiverse
free
eachine e010 scisky tx01 by yoannwyffels
...versions less weight
adding "elevator" to rise up a little bit scisky mount and avoid any interferences with propellers
thingiverse
free
Quanum pico (SciSky board) Cover by ixxe
... to fit smaller x shaped frames. use adhesive tejp to stick it to frame.
top cover is somewhat tight to keep it holding together.
thingiverse
free
Scisky Case (Mounting Plate and Cover) by BrainFever
...commercial frame.
there are two versions... the regular plate and cover as well as a "lightened" version of both parts.
thingiverse
free
Y4 micro scisky 7mm motors multi rotor experimental by Braaping_Pirate
... pusher on the rear motor counter rotating
motors are 7mm
designed to use the scisky board
and fx798t cam
model is glued together
thingiverse
free
Scisky 32bits Brushed Flight Control case by Ipoc78
...2bits brushed flight control case by ipoc78
thingiverse
i need a way to mount the little fc, so i came put with this, works well
thingiverse
free
FunQ Mini FPV Quad - Quanum Pico / Scisky 32 by m4RT1n
...ponents yet to try it out so stay tuned for updates :)
have fun...
if you like it please follow me or/and give it a like :) , thx
105
3ddd
free
МООН 105
...моон 105
3ddd
угловой
модель 105
design_connected
$13
MC 105
...mc 105
designconnected
l'abbate mc 105 armchairs computer generated 3d model. designed by gio ponti.
3ddd
free
Акватон / Мурано 105
...акватон / мурано 105
3ddd
акватон
умывальник акватон мурано 105
turbosquid
$10
Bedcloth 105
... free 3d model bedcloth 105 for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1531182)
turbosquid
$8
Table 105
...lty free 3d model table 105 for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1503775)
turbosquid
$15
Curtain 105
...e 3d model curtain 105 for download as max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1618007)
turbosquid
$4
LP-105
...y free 3d model lp-105 for download as max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1590535)
3d_export
$5
syrena 105
...syrena 105
3dexport
syrena car model
3ddd
$1
Акватон / Стамбул 105
...акватон / стамбул 105
3ddd
россия , акватон
комплект мебели акватон стамбул 105 (россия)
3ddd
$1
Акватон Жерона 105
...акватон жерона 105
3ddd
акватон , жерона
мебель фабрики акватон коллекция жерона 105
Quadcopter
3d_export
$5
quadcopter
...quadcopter
3dexport
futuristic quadcopter design.<br>original design davidflo 77
turbosquid
$19
quadcopter
...lty free 3d model quadcopter for download as max, ma, and obj on turbosquid: 3d models for games, architecture, videos. (1591426)
turbosquid
$25
QuadCopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Quadcopter 3D Model
...quadcopter 3d model
3dexport
quadcopter studio shaders
quadcopter 3d model vortex333 93968 3dexport
3d_export
$5
Quadcopter 3D Model
...quadcopter 3d model
3dexport
quadcopter aircraft helicopter
quadcopter 3d model greatghost 94019 3dexport
3d_export
$18
passenger quadcopter
... a multicopter is an aircraft built according to a helicopter scheme, with three or more rotors. previews rendered with redshift.
turbosquid
$159
Quadcopter Animated.
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Drone Quadcopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Drone Quadcopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$29
Quadcopter
...
questions about the continuation of the collection or the model can be asked here:<br>https://www.artstation.com/evgen_beg
Fpv
turbosquid
$1
FPV VTX Antenna
...e 3d model fpv vtx antenna for download as obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1230317)
3d_export
$9
Fpv logo 3D Model
...onogram vehicle part of auto transport 3d model logo emblem detailed high quality badge
fpv logo 3d model rmodeler 59628 3dexport
3d_export
$8
dji fpv battery slot holder
...er for 3 dji fpv batteries. holds perfectly without shaking. need 1 m3 countersunk head bolt. need to print 6 pin, 1 case, 1 cap.
3d_export
$10
fpv camera hd 700tvl
...aterials are logically named<br>the main format is in 3ds max 2009.<br>satisfcation garranteed..<br>thank you !
thingiverse
free
FpV Mount (SOPORTE FPV) by elborjas1987
...fpv mount (soporte fpv) by elborjas1987
thingiverse
this is a fpv mount with the same holes of naza base.
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
FPV DRONE ROOSTER DJI FPV PART
...fpv drone rooster dji fpv part
thingiverse
fpv drone rooster dji fpv install part
thingiverse
free
FPV monitor
...tml?rmmds=myorder&cur_warehouse=cn
link for download : https://cults3d.com/fr/mod%c3%a8le-3d/divers/fpv-monitor-ecran-fpv-faf
thingiverse
free
FPV receiver mount for FPV display by petrex
...eceiver mount for fpv display by petrex
thingiverse
aomway receiver mount for field view 777 fpv monitor. with small cable tray.
5Mm
3d_export
$25
5mm Explosive Flechette 3D Model
...xplosive flechette 3d model
3dexport
assault rifle grenade launchers
5mm explosive flechette 3d model awnonbhowmik 74565 3dexport
turbosquid
$15
engagement simple ring with diamond (5mm)
...engagement simple ring with diamond (5mm) for download as 3dm on turbosquid: 3d models for games, architecture, videos. (1157278)
turbosquid
$1
Flexible shaft coupling 5mm x 8mm
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$7
Tiny bracelet clasp lock 20mm X 5mm
... your bracelet parts to the clasp, also there is the original file in the files so you can change it on your own simply. enjoy it
3d_export
$5
cross with text jesus
...the text jesus is in an contur offset with 5mm ...
3d_export
$5
ring
...ring 3dexport lovely ring, adopt for print, one stown 5mm material : white / yellow gold/ silver. stl,...
3d_export
$11
crescent ring
...ring size is 17mm.<br>ring rail size is 53.4<br>stone size 5mm ...
3d_export
$5
Hex Spacers M3 Male-Female
...male-female 3dexport hex spacers m3 male-female with length from 5mm to 60mm for printed circuit boards. step...
3ddd
$1
LOOP RACK
...вешалка the clothes rack’s elegant frame is made of 5mmthick steel. it creates simple shapes, that vary depending on...
3d_export
free
solar rechargeable single led flashing light
...ties onto a pole etc, i used a single 5mm red/blue alternating flasher that pushes snugly into the 5mm...
Micro
3ddd
$1
Micro
...micro
3ddd
автобус
turbosquid
$80
MICRO
...ty free 3d model micro for download as max, c4d, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1700743)
3ddd
$1
JBL Micro Wireless
... micro , колонка , плеер
jbl micro wireless
turbosquid
$10
Suppressor Micro
...quid
royalty free 3d model suppressor micro for download as on turbosquid: 3d models for games, architecture, videos. (1380433)
turbosquid
$20
Micro Meter
...osquid
royalty free 3d model micro meter for download as fbx on turbosquid: 3d models for games, architecture, videos. (1350448)
turbosquid
$7
NIghtstand Micro
...d
royalty free 3d model nightstand micro for download as max on turbosquid: 3d models for games, architecture, videos. (1248117)
3ddd
$1
Micro wind turbine
...micro wind turbine
3ddd
турбина
micro wind turbine for your green building projects
turbosquid
$29
Micro Speakers
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$29
Micro Servo.max
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
Micro cells
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Motors
archibase_planet
free
Motor
...base planet
motor motor engine engine electric motor
motor wagner n250213 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Motor
...motor
archibase planet
motor motor engine engine
motor n151112 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Motor
...motor
archibase planet
motor motor engine engine
motor n150615 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
turbosquid
$15
Motor
...otor
turbosquid
royalty free 3d model motor for download as on turbosquid: 3d models for games, architecture, videos. (1639404)
3d_ocean
$5
Electric motor
...electric motor
3docean
car electric engine industry motor phase train vehicle
an electric motor enjoy!
3d_ocean
$18
Electric Motor
...electric motor
3docean
electric motor engine machine mover parts
3d model electric motor for hoist crane
turbosquid
$29
Motor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$5
Motor
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
electric motor
...electric motor
3dexport
electric motor use for industrial purposes
3d_export
$5
servo motor
...tor
3dexport
it's a simple part of servo motor 0.75kw for used in machines assembly to show specified motor in own project.
8
turbosquid
$6
Rock 8-8
...urbosquid
royalty free 3d model rock 8-8 for download as obj on turbosquid: 3d models for games, architecture, videos. (1659393)
3ddd
$1
Italamp 387/8+8
...italamp 387/8+8
3ddd
italamp
люстра italamp 387/8+8
размеры 92x71h
3ddd
$1
8 марта
...8 марта
3ddd
8 марта
кресло 8 марта
design_connected
$16
No 8
...nected
photo-realistic 3d models of the sibast no 8 armchair from sibast for 3d architectural and interior design presentations.
3d_export
$5
hinge 8
...hinge 8
3dexport
hinge 8
3d_export
$5
iphone 8
...iphone 8
3dexport
iphone 8
turbosquid
$69
iPhone 8 and iPhone 8 Plus
... free 3d model iphone 8 and iphone 8 plus for download as max on turbosquid: 3d models for games, architecture, videos. (1202442)
turbosquid
$12
Calligraphic Digit 8 Number 8
...hic digit 8 number 8 for download as max, obj, fbx, and blend on turbosquid: 3d models for games, architecture, videos. (1389341)
3ddd
free
PLANTS 8
...plants 8
3ddd
цветок , горшок
plant 8,,, hope u all like it
3ddd
$1
8 Марта / Amadey
...8 марта / amadey
3ddd
8 марта
8 marta amadey