mgn12 bracket by peanutwarrior

...warrior thingiverse this bracket attaches to an mgn12 block and allows connection of another linear guide to create the x motion

...ccess that hole that was drilled in the 'x axis' bar. this is required to install the bracket without removing any parts.

...interface with dual mgn12 sliders mounted on the top and bottom of a t3030 frame. work in progress, measurements not yet correct.

... you will need to change the belt drive for the x-axis. the parts i used are on thingiverse. check the tevo tarantula collection.

...se these were the pulley parts for the mgn12 bracket i made, these fit onto the other pulley design. you only need two of these.

...near rails on a 20mm aluminum extrusion. print two or more and snap them on the mgn12 and the rail and tighten your m3 cap bolts.

...ior thingiverse this bracket allows a nema motor to be mounted by the four rear bolts and then bolted onto a 4040 extrusion rail

... just bolt 3 spaced out underneath a linear rail with m3 nuts and bolts, then push into the slot of the extrusion for a push fit.

... heavily modified. this version is completely separate and mounts to the mgn12 bracket i designed. one of each for left and right

...he front side z axis on a c/d-bot. mounts to 20mm extrusion via two 5mm bolt holes and the four carriage holes are of course 3mm.

...4040 foot by peanutwarrior thingiverse simple foot to attach to 4040 extrusion

...3030 bearing holder by peanutwarrior thingiverse bracket for mounting a linear bearing block to 3030 extrusion

...t8 mount 4040 by peanutwarrior thingiverse this block allows for a t8 aluminum guide to be bolted in onto 4040 extrusion

...m12 mounting block 4040 by peanutwarrior thingiverse holding block for 4040 to hold 12mm rod.

...warrior thingiverse this bracket attaches to an mgn12 block and allows connection of another linear guide to create the x motion

...ior thingiverse this bracket allows a nema motor to be mounted by the four rear bolts and then bolted onto a 4040 extrusion rail

...t by peanutwarrior thingiverse this bracket holds a nema 17 59mm motor upside down inside a 4040 frame for use in a corexy setup

...se these were the pulley parts for the mgn12 bracket i made, these fit onto the other pulley design. you only need two of these.

...3030 lead screw brass mount by peanutwarrior thingiverse this block allows the ability to support the brass t8 thread

...mgn12 stopper by henning36 thingiverse a end peace for mgn12 rails

...mgn12 abdeckkappen by zyrusthc thingiverse einfache abdeck kappen für die mgn12 führungen

...montagehilfe mgn12 by nero_x84 thingiverse montagehilfe zur montage von mgn12 linearschienen auf 20x20 aluprofilen.

...mgn12 toprail mount for hemera thingiverse hemera mount for mgn12 rails on top like the am8

...end stop for mgn12 railing thingiverse end piece to stop the slider from coming off the mgn12 rail.

...near rails on a 20mm aluminum extrusion. print two or more and snap them on the mgn12 and the rail and tighten your m3 cap bolts.

...direct drive ender 5 mgn12 thingiverse direct drive ender 5 mgn12

...warrior thingiverse this bracket attaches to an mgn12 block and allows connection of another linear guide to create the x motion

...hypercube with linear mgn12 rail by 3dfastprint thingiverse remixered hypercube evo with linear guide mgn12

...bracket archibase planet bracket corbel holder bracket 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet bracket corbel console bracket 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet corbel holder bracket bracket 6 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet bracket corbel console bracket 8 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet bracket corbel holder bracket n280911 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet holder corbel bracket bracket 9 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet corbel holder bracket bracket 10 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet corbel console bracket bracket 11 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet holder console bracket bracket 12 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...bracket archibase planet bracket corbel holder bracket 13 - 3d model (*.gsm+*.3ds) for interior 3d visualization.