MAX7219 - 4 in 1

...8x8 matrix for temperature, arduino, gps by mathiastenge thingiverse for 3x 8x8led matrix (small max7219-modules) with dasychain

...case for max7219 by oxygen_ thingiverse case for max7219

...max7219 7segment anzeige by mathiastenge thingiverse 7segment max7219

...attery and a esp8266 from lolin. the only thing you need to design is a stand / mount for your car or where you want to mount it.

...max7219 case thingiverse wall case for max7219 dot matrix. with space for esp8266 board.

...and a wemos d1 mini. you might break a few clips when inserting the led modules, but there are enough, so it should not matter :)

...se for dot matrix (max7219 - 32x8) by _phoenix_ thingiverse use for max7219 dot matrix with space for esp8266 below the display.

...btc ticker max7219 case by lancsi thingiverse btc ticker case for max7219 led display and wemos d1 mini.

...e build info is at:https://marksbench.com/electronics/temperature-and-humidity-display-using-arduino,-dht22,-and-max7219-display/

...hoto as you see in photo, i straightened the pins , then heated the pins one at a time and pushed them through to opposite side.

...max7219 case thingiverse wall case for max7219 dot matrix. with space for esp8266 board.

...case for max7219 by oxygen_ thingiverse case for max7219

...max7219 7segment anzeige by mathiastenge thingiverse 7segment max7219

...btc ticker max7219 case by lancsi thingiverse btc ticker case for max7219 led display and wemos d1 mini.

...se for dot matrix (max7219 - 32x8) by _phoenix_ thingiverse use for max7219 dot matrix with space for esp8266 below the display.

...ww.thingiverse.com/thing:2282497 provides a hole for the microusb of a nodemcu or wemos d1 stuck to the back of the max7219 unit.

... fit. no tools or other hardware needed. just print, press in the max7219 and press it onto the folgertech prusa i3's frame.

..., and so i made this. the modules i used i just got for cheap off of amazon. printed with pla on an ender 3 pro. use supports.

...modules. freecad design is included so you can make the frame as long as you like. my frame is for a simple esp32 driven clock.

...arceau 4*4 jetman by jps57550 thingiverse arceau de rechange pour le 4*4 jetman

...4 x 4 bench by pangeaexpress thingiverse 3d model of our 4 x 4 bench. designed by eric arneson & nahal sohbati

...4 by pencilpomelo thingiverse 4

...4 by yangchigi thingiverse 4

...base for connect 4 puissance 4 by doubidou thingiverse connect 4 base puissance 4

...#4 by ak47vogt thingiverse 4 part

...4 sharkz thingiverse 4 sharkz

...n_9922z thingiverse a larger 4 by 4 version of my old lattice cube that will test your printer even more. once again, good luck!

...4 gewinnt / connect four / 4 in a row thingiverse 4 gewinnt

... inch hoses together. i used the adapter to connect two aluminum dryer hoses to exhaust the fumes from my chinese laser engraver.

...magic token +1/+1 & -1/-1 by kilgara2b thingiverse a magic the gathering token +1/+1 and -1/-1

...tudiosgaming thingiverse if you are in need of the 4pstudiosgaming +1/+1 and -1/-1 counters, then you came to the right page :-p

... 1/6, 1/8, 1/10, and 1/12 sized wedges as well as a circular base for them to fit onto. there are no labels on any of the pieces.

...dapter for syphon - 1 1/4" to 1 1/2" h10,5mm the project was realized with tolerances for printing with abs + tape ptf.

...l fit both 1 1/8" and 1 1/5" bearing cups. i used a 3/8ths" threaded rod with nuts and thick washers on each end.

...design cheeseborough clamp for hanging lightfixtures and other items onto 1-1/4"-1-1/2" npt pipe. use at your own risk.

...them instead of money coin in your supermarket cart or in your swimming pool locker. edit : updated 1£ coin with new dimensions

...d adapter 1" to 1" 1/4 by printerforever thingiverse this is an adapter 1" to 1" 1/4 (male to male) enjoy !

...playstation 2, 1:1 by vitting thingiverse made a 1:1 playstation 2.

...re thinner and actually fit within each other to show equivalent fractions. also, check out the same version with braille (here).