Thingiverse
Masterspool 800g PLA Wood by Alegoty
by Thingiverse
Last crawled date: 3 years, 1 month ago
The German translation is below.
I had lots of plywood lying around and didn't want to waste unnecessary filament on a completely printed masterspool. About 54 grams of PLA are needed.
Three wood screws 3.5 x 15 mm, three threaded rods M4 x 22 mm and 4 nuts M4 are needed.
My plywood was 5 mm thick ...
Please print without support.
On the bottom side, the wooden disk is screwed with 3.5 x 15 mm screws.
On the top side a 22 mm long threaded rod M4 is screwed in, so that it still looks up 11 mm, then the upper wooden disk with the knobs can be screwed in place.
Drive the nut into the knob with the hammer.
The threaded rods can be easily made from screws for cabinet handles - just saw off the head.
I didn't design the knob, it's from Bart ter Haar.https://www.thingiverse.com/thing:641854/makes
Attention. Please insert the filament in such a way that the buttons do not jam with the holder of the roll. See picture.
##################################
Ich hatte noch jede Menge Sperrholz herumliegen und wollte nicht unnötig viel Filament für eine komplett gedruckte Masterspool verschwenden. Es werden ca. 54 Gramm PLA benötigt.
Es werden drei Holzschrauben 3,5 x 15 mm, drei Gewindestäbe M4 x 22 mm und 4 Muttern M4 benötigt.
Mein Sperrholz war 5 mm stark ...
Bitte ohne Stützstruktur drucken.
An der Unterseite wird die Holzscheibe mit 3,5 x 15 mm Schrauben verschraubt.
Auf der Oberseite wird ein 22 mm langer Gewindestab M4 herein gedreht, so das er noch 11 mm weit heraufschaut, dann kann die obere Holzscheibe mit den Knöpfen festgeschraubt werden. Die Mutter mit dem Hammer in den Knopf einschlagen.
Die Gewindestäbe lassen sich leicht aus Schrauben für Schrankgriffe herstellen - einfach den Kopf absägen.
Den Knopf habe ich nicht entworfen, er ist von Bart ter Haar.https://www.thingiverse.com/thing:641854/makes
Achtung! Bitte das Filament so einlegen, das die Knöpfe nicht mit der Halterung der Rolle verklemmen. Siehe Bild.
I had lots of plywood lying around and didn't want to waste unnecessary filament on a completely printed masterspool. About 54 grams of PLA are needed.
Three wood screws 3.5 x 15 mm, three threaded rods M4 x 22 mm and 4 nuts M4 are needed.
My plywood was 5 mm thick ...
Please print without support.
On the bottom side, the wooden disk is screwed with 3.5 x 15 mm screws.
On the top side a 22 mm long threaded rod M4 is screwed in, so that it still looks up 11 mm, then the upper wooden disk with the knobs can be screwed in place.
Drive the nut into the knob with the hammer.
The threaded rods can be easily made from screws for cabinet handles - just saw off the head.
I didn't design the knob, it's from Bart ter Haar.https://www.thingiverse.com/thing:641854/makes
Attention. Please insert the filament in such a way that the buttons do not jam with the holder of the roll. See picture.
##################################
Ich hatte noch jede Menge Sperrholz herumliegen und wollte nicht unnötig viel Filament für eine komplett gedruckte Masterspool verschwenden. Es werden ca. 54 Gramm PLA benötigt.
Es werden drei Holzschrauben 3,5 x 15 mm, drei Gewindestäbe M4 x 22 mm und 4 Muttern M4 benötigt.
Mein Sperrholz war 5 mm stark ...
Bitte ohne Stützstruktur drucken.
An der Unterseite wird die Holzscheibe mit 3,5 x 15 mm Schrauben verschraubt.
Auf der Oberseite wird ein 22 mm langer Gewindestab M4 herein gedreht, so das er noch 11 mm weit heraufschaut, dann kann die obere Holzscheibe mit den Knöpfen festgeschraubt werden. Die Mutter mit dem Hammer in den Knopf einschlagen.
Die Gewindestäbe lassen sich leicht aus Schrauben für Schrankgriffe herstellen - einfach den Kopf absägen.
Den Knopf habe ich nicht entworfen, er ist von Bart ter Haar.https://www.thingiverse.com/thing:641854/makes
Achtung! Bitte das Filament so einlegen, das die Knöpfe nicht mit der Halterung der Rolle verklemmen. Siehe Bild.
Similar models
thingiverse
free
K40 Laser Bed enhancement / Laser Bett Erweiterung by Creative_Carsten
...t für mich sehr gut. hier werden benötigt:
3 x m4 mutter
1 x m4 innensechskantschraube 30 mm
1 x m4 innensechskantschraube 10 mm
thingiverse
free
EWD Waage für RC Logger DPG-02L - Incidence meter digital by UL-Pilot
...on the bevel box hold the bevel box on the holder.
i also designed a wall mount to be able to store the incidence meter properly.
thingiverse
free
Filament-Guide, Filamentführung Genius by Hans-G
...de 5 mm). finally, the old holder of the sensor is fixed as filament guide at the top of the holder with the corresponding screw.
thingiverse
free
Filament-Guide, Filamentführung Sidewinder X1 by Hans-G
...de 5 mm). finally, the old holder of the sensor is fixed as filament guide at the top of the holder with the corresponding screw.
thingiverse
free
Filament-Führungs-Rolle für SOVOL SV02 by MX-Trainer
...rwendung der rollen mit lager, werden 2 st. 608er kugellager benötigt.
ich habe die rolle aus tpu und den halter aus pla gedruckt
thingiverse
free
Soldering fume fan by Dionarap
...e 92mm fan is simply attached to the frame with the clips.
the following is required:
3x hexagon socket screw m4 x 35mm
3x nut m4
thingiverse
free
Halter für Luftdaten Sensor by bamboozeler
...empfehle die 75er schelle zwei mal und die 80er schelle ein mal zu drucken.
edit: 29.04.2019 step dateien der modelle hinzugefügt
thingiverse
free
siku adapter by AMCR
...r den druck sollte der adapter um 90 grad gedreht werden damit die stützstruktur unter
sich unter den haltern für den frontlader.
thingiverse
free
Bearing Filament Spool Holder for LK4pro by Dr_InSide
...ball bearings for the longer3d lk4 and lk4pro (and similar 3d printer. it guarantees a smooth rolling of the...
thingiverse
free
Ersatzteil - Fuxtec CT-500 Knopf für den Bügel by kleinsimon
...ert und ist davongeflogen. da es nach der bescherung in den urlaub gehen sollte, konnte nicht auf ein ersatzteil gewartet werden.
Alegoty
thingiverse
free
Gasflaschenschlüssel by Alegoty
...pressure reducer for gas cylinders. remains on the gas bottle and can thus not be lost.
infill min.80% and print without support!
thingiverse
free
IKEA HAMMARN - improved spare part for the skids by Alegoty
...t silikon oder heißkleber befestigen.
ikea hammarn - verbessertes ersatzteil für die kufen.
please fix with silicone or hot melt.
thingiverse
free
Hex Screwdriver Handle - Griff für Bithalter by Alegoty
...upport
sechskantdesign, um ein wegrollen des schraubendrehers zu verhindern.
farbwechsel bei ebene 105
ohne stützstruktur drucken
thingiverse
free
Clip for edge banding machine - Kantenklammer für Kantenmaschiene by Alegoty
...hick.
######################
clip für die kantenrollen der kantenmaschiene in der schreinerei.
für kantenrollen bis 26 mm stärke.
thingiverse
free
Holder for Gardena garden sprayer - Halter für Gardena Gartenbrause by Alegoty
... classic gartenbrause.
bitte mit mindestens 50% infill und ohne stützen drucken.
pla funktioniert, petg funktioniert besser ....
thingiverse
free
Addon for Lea / internal portion from InJoyUs by Alegoty
...u und mit support.
mit ein wenig gleitgel lässt sich das addon leicht aufsetzen.
für verbesserungsvorschläge bin ich dankbar. ;-)
thingiverse
free
Handle for shut off valve water - Griff für Absperrventil Wasser by Alegoty
...rucken.
handle for shut-off valve, 100mm (diameter) x 10 mm (square)
din 390 b handwheel with shaft collar
print without support.
thingiverse
free
Grow vegetable onions - Gemüsezwiebeln vorziehen by Alegoty
...ehen, sonst fängt die zwiebel an zu faulen.
für marmeladengläser die an der öffnung 78mm durchmesser haben.
ohne support drucken.
thingiverse
free
Grow vegetable onions - Gemüsezwiebeln vorziehen by Alegoty
...ehen, sonst fängt die zwiebel an zu faulen.
für marmeladengläser die an der öffnung 78mm durchmesser haben.
ohne support drucken.
thingiverse
free
Clip for pencil - Clip für Bleistift by Alegoty
...cken um eine gute verbindung zwischen den schichten zu erhalten.
eine schichtdicke von 0,1 mm ist optimal, 0,2 funktioniert auch.
800G
thingiverse
free
LG PW600G-800G Projector Lens Cover by youngwing
...are you serios lg? where is that's lens cover? ok ok no problem, we'll take care, makers.
the material is flex and fits.
thingiverse
free
SLIK Insta-Lok 800G-FL Tripod Center Column Ring Replacement Part by BalooRM
...fl tripod center column ring. this ring holds the 3 leg braces. the original part on my tripod broke after many years of service.
thingiverse
free
BMW F7/800GS Headlight Caps by prateekrajbhandari
...e it a little bit of compatible lube to reduce friction. the printed parts are a bit compromised for strength at the extremities.
thingiverse
free
Smart self-watering plant system in a 800g metal can from the supermarket by Plantmaster
...he plant some nutrition.
you need:
-a plant
-800g can (with coating inside)
-old face mask or laces
(-fresh soil)
(-fertillizer)
thingiverse
free
FlashForge Spool Holder for Sainsmart TPU 800g spool by LongWindFPV
...nd filament use down to a minimum, while taking advantage of the support feature to ensure the tube holder is sturdy and durable.
thingiverse
free
Cat and Dog Food Divider for 800g Tin Cans by xSnowHeadx
...ntinue the rotation.
this model is just under development. i would be glad to get feed back and suggestions for its improvement.
thingiverse
free
float, ponton for fischertechnik different versions by thomasdr
...cascadable part 1: 50x50x200 300g buoyancy part 1: 80x80x200 800g ...
thingiverse
free
LED adapter for LED lights of 1200GS by maddash1337
...mount my led lights from a 1200gs to my 800g update v2 - drilling diameter...
thingiverse
free
Another Filament Roller by NoIsIm
...filament roller by noisim thingiverse another roller !! pictures: 800g spool and 2600g spool. very robust design. printet in...
Masterspool
thingiverse
free
Masterspool para filamento TECNIKOA
...masterspool para filamento tecnikoa
thingiverse
masterspool para filamento tecnikoa
thingiverse
free
MasterSpool - Remixed Design by MisterFloyde
...masterspool - remixed design by misterfloyde
thingiverse
creatred a design remix of the masterspool by dasfilament from scratch.
thingiverse
free
Masterspool holder by bubblefish
...simple holder for the masterspool,
its printed with petg with 20% infill,
the version 1 is not very good, the version 2 is better
thingiverse
free
3DS Masterspool Minimal
...s universal auto-rewind spool holder, then the re-winder axle nuts can get a grip on the cardboard hub when it is tightened down.
thingiverse
free
Masterspool by tuxmakesthings
...t and print time, and to have a filament catch that doesn't have the filament end poke into any plastic bag used for storage.
thingiverse
free
MasterSpool Refill light version v2
...masterspool refill light version v2
thingiverse
light version of masterspool with increased gaps between thread.
thingiverse
free
Masterspool - Twist and Lock - with bearings by banolka
...ool - twist and lock - with bearings by banolka
thingiverse
remix of masterspool - twist and lock by 3d-workshop to fit bearings
thingiverse
free
3D SOLUTECH MASTERSPOOL by 3Dsolutech
...r instagram 3dsolutech and receive promotions on 3d solutech filaments.
feel free to ask us any questions at info@3dsolutech.com
thingiverse
free
MasterSpool V4 for SpannerHands Spool System by Dravpnir
... richrap modified to be easily used in the spannerhands spool system. idea came from chrizlle with his mod on the masterspool v3.
thingiverse
free
1kg Masterspool - 3DTomorrow Filament
...do so via the following links:https://3dtomorrow.com/product/masterspool-pla/https://3dtomorrow.com/product/masterspool-silk-pla/
Pla
turbosquid
$20
'Plas" Table Lamp
... 'plas" table lamp for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1277537)
turbosquid
$400
PLA Chinese Soldier artillerymen
...3d model pla chinese soldier artillerymen for download as max on turbosquid: 3d models for games, architecture, videos. (1668792)
turbosquid
$400
PLA Chinese Soldier navy
...ty free 3d model pla chinese soldier navy for download as max on turbosquid: 3d models for games, architecture, videos. (1668787)
turbosquid
$250
PLA Chinese Soldier 01
...alty free 3d model pla chinese soldier 01 for download as max on turbosquid: 3d models for games, architecture, videos. (1668799)
turbosquid
$250
PLA Chinese Soldier 06
...alty free 3d model pla chinese soldier 06 for download as max on turbosquid: 3d models for games, architecture, videos. (1668809)
turbosquid
$250
PLA Chinese Soldier 05
...alty free 3d model pla chinese soldier 05 for download as max on turbosquid: 3d models for games, architecture, videos. (1668807)
turbosquid
$250
PLA Chinese Soldier 03
...alty free 3d model pla chinese soldier 03 for download as max on turbosquid: 3d models for games, architecture, videos. (1668804)
turbosquid
$200
PLA Chinese Soldier 02
...alty free 3d model pla chinese soldier 02 for download as max on turbosquid: 3d models for games, architecture, videos. (1668803)
turbosquid
$100
PLA Chinese Soldier 74
...alty free 3d model pla chinese soldier 74 for download as max on turbosquid: 3d models for games, architecture, videos. (1668839)
turbosquid
$100
PLA Chinese Soldier 71
...alty free 3d model pla chinese soldier 71 for download as max on turbosquid: 3d models for games, architecture, videos. (1668829)
Wood
3ddd
$1
Wood
...wood
3ddd
wood
3ddd
$1
Wood
...wood
3ddd
wood
3ddd
$1
Wood
...wood
3ddd
wood
3ddd
$1
Wood
...wood
3ddd
wood
3ddd
$1
Wood
...wood
3ddd
доска
wood
3ddd
$1
Wood
...wood
3ddd
доска
wood
3ddd
$1
wood
...wood
3ddd
дрова
wood, log
3d_ocean
$3
Wood Crate
...wood crate
3docean
box crate wood
a model of a wood crate
3ddd
free
Wood crafts
...wood crafts
3ddd
wood , crafts
wood crafts of chinese style
turbosquid
$2
Wood
...od
turbosquid
royalty free 3d model wood for download as obj on turbosquid: 3d models for games, architecture, videos. (1576561)