Thingiverse
Maskit by cgiacomo
by Thingiverse
Last crawled date: 3 years, 4 months ago
The Maskit is a simple device to adjust the tension and fit for just about any tension-based masks. One side is permanently attached, and the other is easily slipped over the hooks to put on. Once you know roughly what setting works for you, trim off the excess for a more comfortable fit.
Design is Patent Pending, and not for commercial re-use or production without the explicit consent of Ideation Arms, LLC.
Design is Patent Pending, and not for commercial re-use or production without the explicit consent of Ideation Arms, LLC.
Similar models
3dwarehouse
free
maskitizers 2 capstone
...maskitizers 2 capstone
3dwarehouse
capstoone sns fdb
3dwarehouse
free
maskitizers Sns FBD capstone
...maskitizers sns fbd capstone
3dwarehouse
samya, anaya, ishika, lakshi, sadhya
3dwarehouse
free
Tension Fitting
...tension fitting
3dwarehouse
cable railing 3/16' cable tension fitting
thingiverse
free
VW T4 parkingbreak tensioner 701711367 701711247 by stexo
...nsioner 701711367 701711247 by stexo
thingiverse
parking break tensioner for vw t4.
if you cut a m12 thread it will fit better.
3dwarehouse
free
Non-Tensioning Fitting
...non-tensioning fitting
3dwarehouse
cable railing 3/16' cable non-tension fitting
grabcad
free
Quad Tension Hardware Fitting for Hex conductor
...quad tension hardware fitting for hex conductor
grabcad
765 kv quad tension hardware fitting for hex conductor
grabcad
free
Quad Tension Hardware Fitting for Quadruple conductor
...quad tension hardware fitting for quadruple conductor
grabcad
400 kv quad tension hardware fitting for quadruple conductor
thingiverse
free
XBelt Tensioner by Insomniac555
...0 is a nightmare,
so this mod not only makes things a little easier but also enables you to tension or loosen easily and quickly.
thingiverse
free
X belt tensioner for flyingbear P902 by cederron
...he tension fast and easy.
installation takes 1 minute.
you will need 2 m4 screws and nuts, the nuts are press fit into the piece.
thingiverse
free
X-Belt Tensioner Anet Short Lack by JPK89
...tle bit smaller to fit into the lack box.
you need 2x m3x10 screws
you can heat up the nuts with a lighter to fit into the holes.
Maskit
Cgiacomo
thingiverse
free
Cinequeen GPS Mount by cgiacomo
...a tray and mount for the geprc cinequeen. designed for the bn-880 compass/gps to turn your cinequeen into a long range gps drone.
thingiverse
free
NATO Rail Mount by cgiacomo
...t for hanging standard accessories from a drone. should fit standard tactical lights, lasers, or any rifle-mounted rail accessory
thingiverse
free
Flamewheel F450 Landing Gear by cgiacomo
...alent knock-offs. design mounts with m3/m4 screws through the base plate, and has holes for additional mounting rails if desired.
thingiverse
free
Drone NATO Rail Gimbal by cgiacomo
...ry weight should be under 300g in order to avoid over-loading the servos, but design should scale up to full size servos as well.
thingiverse
free
L2/L5 GPS Antenna by cgiacomo
...design can be found at the links below.
http://jcoppens.com/ant/qfh/calc.en.phphttps://www.pinterest.com/pin/525373112773545290/
thingiverse
free
Form for quadrifilar helix antenna by KerwoodDerby
...form for quadrifilar helix antenna by kerwoodderby thingiverse with cgiacomo#39;s l2/l5 antenna form (https://www.thingiverse.com/thing:4684888), i struggled because i couldn't...