GrabCAD
ManiCopter
by GrabCAD
Last crawled date: 1 year, 11 months ago
So this is our first time doing a design and a 3D print, so a lot of mistakes were made. This is an effort to recognize and learn from those mistakes.
The inspiration for this design came from the
1. Concept of autorotation (https://en.wikipedia.org/wiki/Autorotation ).
2. Landing legs of falcon 9 rocket by SpaceX.
3. Using radial contact to hold the egg , done by Lehaiver .
The design was printed but a few crucial mistakes related to DFM (Design for Manufacturing) made it impossible to assemble.
1. First mistake is the legs and their connection to the central cupola, it is too complicated, plus there was no clearance left for a fit (should be 0.3 mm).
2. The springs to attach the egg housing to each other should be tight enough, right now they are too lax hence it can easily slide off.
3. The blades should have more surface area.
Hopefully this excercise has not gone in vain and we have learned some valuable lessons in design esp. Design for 3d printing.
Cheers
-Manan and Imran
The inspiration for this design came from the
1. Concept of autorotation (https://en.wikipedia.org/wiki/Autorotation ).
2. Landing legs of falcon 9 rocket by SpaceX.
3. Using radial contact to hold the egg , done by Lehaiver .
The design was printed but a few crucial mistakes related to DFM (Design for Manufacturing) made it impossible to assemble.
1. First mistake is the legs and their connection to the central cupola, it is too complicated, plus there was no clearance left for a fit (should be 0.3 mm).
2. The springs to attach the egg housing to each other should be tight enough, right now they are too lax hence it can easily slide off.
3. The blades should have more surface area.
Hopefully this excercise has not gone in vain and we have learned some valuable lessons in design esp. Design for 3d printing.
Cheers
-Manan and Imran
Similar models
thingiverse
free
Vegeta Zipper Pull by rcortes51
...nted after learning sketchup.
measures 3" x 2" x 1/4"
i should have made it smaller takes about an hour to print.
thingiverse
free
Wingspan egg and food box for the Oceania expansion by alvrod
...the right size. for validation the tokens are 2 cm in diameter so that is the diameter that you are looking to have in the holes.
3dwarehouse
free
House
...tter than my first because i learned from my mistakes. #dream #dream_home #dream_house #home #house #lovely #pretty #pretty_house
grabcad
free
4-leg spider robot
...4-leg spider robot
grabcad
it is my first time to design a robot so there may be some mistake.
thingiverse
free
LSP Star Tiara v2.0 by meevchan
... from my first design i made some changes that resulted in this version. i am still a total beginner. this was made in tinkercad.
grabcad
free
Egg of Thrones
...do not have access to a 3d printer but i thought this was an amazing design challenge so i thought i would submit my idea anyway!
thingiverse
free
Digi-Egg of Reliability by birwin
...of the digi-egg of reliability from digimon adventure 2. this is just a single part and should be able to print with no supports.
thingiverse
free
Digi-Egg of Knowledge by birwin
...n of the digi-egg of knowledge from digimon adventure 2. this is just a single part and should be able to print with no supports.
thingiverse
free
Building - Walls #3 (Damage)
... i will update these designs!
all the designs are made with the intent that they should be easy to print without to much support.
thingiverse
free
arduino by nevazza
...urn out it was build just to learn basics of tinkercad so if you decide to print it feel free to leave a comment and a picture :)