Thingiverse
locking hinge by jonspencer
by Thingiverse
Last crawled date: 3 years, 1 month ago
I'm trying to make a kind of hinge that locks into place with a screw in the middle, hence the teeth. I guess that this one will lock into 30 degree increments. I drew another that will lock together at 20 degree increments.
Similar models
thingiverse
free
Bevel Protractor by designeddifferent
...tractor allow for locking in at intervals of 22.5 degrees, while 10 degree increments are marked to allow for manual calibration.
thingiverse
free
Bevel Protractor by designeddifferent
...tractor allow for locking in at intervals of 22.5 degrees, while 10 degree increments are marked to allow for manual calibration.
thingiverse
free
BFB Top-lid Hinges by StevenHoogslag
...automatically. the hinges snap on the printer body without any modification. the top can easily be separated and locked-on again.
thingiverse
free
Hinge by RepRapster3d
... liked the design but it would not butt up to a corner at 90 degrees and i needed a hinge for my new electronics casing and door.
thingiverse
free
Single dosing funnel [centered] for Baratza Sette 270* grinders by joshc
...rees which is too much. if i printed again i might go for 6 degrees.
try your luck and reply back here on the most centered one!
thingiverse
free
90 degrees lock by Tmebsis03
...this is a lock for 90 degree corners so i used to make a secure cabinet in my wardrobe using some m4 bolts an a lock to secure it
thingiverse
free
270 degree hinge by gilhilel
... used a welding rode as the axis.
i had to use the drill to insert the metal spoke, but after i did, it's not going anywhere.
thingiverse
free
Hinge to lock a belt
...hinge to lock a belt
thingiverse
i made this to fix a hinge for a helmet and put a belt so i can put the helmet over my head.
thingiverse
free
Chest by Graystone
...e little hinges can be found everywhere. i used small 1.4x7mm screws to attach the hinges and the locking mechanism to the chest.
thingiverse
free
Locksport Safe Lock Manipulation Graph Paper by SAH1376
...s every 2 numbers.
high/low test boxes for 3 wheel locks included on each page.
(spacer included only as stl required for upload)
Jonspencer
thingiverse
free
Rpipe by jonspencer
...rpipe by jonspencer
thingiverse
a pipe
thingiverse
free
Thigh by jonspencer
...thigh by jonspencer
thingiverse
thigh
thingiverse
free
Hinge by jonspencer
...hinge by jonspencer
thingiverse
hinge
thingiverse
free
Stand by jonspencer
...stand by jonspencer
thingiverse
stand
thingiverse
free
Autopilot Mount by jonspencer
...autopilot mount by jonspencer
thingiverse
mount
thingiverse
free
Short Radar by jonspencer
...short radar by jonspencer
thingiverse
short radar for the scale model american beauty
thingiverse
free
Air Horn by jonspencer
...air horn by jonspencer
thingiverse
air horns for the scale model american beauty
thingiverse
free
Watertight door by jonspencer
...watertight door by jonspencer
thingiverse
watertight door for the scale model american beauty
thingiverse
free
saw measuring thing by jonspencer
...saw measuring thing by jonspencer
thingiverse
saw measuring thing
thingiverse
free
Proximity Sensor Holder by jonspencer
...proximity sensor holder by jonspencer
thingiverse
proximity sensor holder
Hinge
thingiverse
free
hinge
...hinge
thingiverse
hinge for rc vehicles
thingiverse
free
hinge
...hinge
thingiverse
just a basic hinge
thingiverse
free
Hinge
...hinge
thingiverse
simple hing for printing at once or piece for piece...
thingiverse
free
Hinge
...erse
hinge in the style of a ladder hinge.
5mm bolt and nut required to allow it to function
5mm screw holes
180 degree rotation
thingiverse
free
hinge by sbenetti1
...hinge by sbenetti1
thingiverse
hinge
thingiverse
free
hinge by Jfpoutasse
...hinge by jfpoutasse
thingiverse
hinge
thingiverse
free
Hinge by KyoFR
...hinge by kyofr
thingiverse
hinge
thingiverse
free
Hinge by jonspencer
...hinge by jonspencer
thingiverse
hinge
thingiverse
free
Hinges by Mahee3D
...hinges by mahee3d
thingiverse
hinges
thingiverse
free
hinge by hobbz
...hinge by hobbz
thingiverse
hinge
Locking
thingiverse
free
Caps Lock Lock by fx137
...caps lock lock by fx137
thingiverse
mechanical lock for the caps lock key suitable for the corsair vengenace k70
thingiverse
free
Barbell Lock
...barbell lock
thingiverse
barbell lock
to lock your barbell up!
thingiverse
free
Door Lock (Box Lock) by ManunaM
...door lock (box lock) by manunam
thingiverse
i made this lock for my tool box
thingiverse
free
U Lock Lock by pessotta
...that holds the u lock on the bike seatpost.
i've removed the bolt and nut housing beacause they are useless and hard to print
thingiverse
free
servo lock
...servo lock
thingiverse
servo lock
thingiverse
free
lock by Bobjrbob
...lock by bobjrbob
thingiverse
a cool lock
thingiverse
free
Beyblade Lock
...beyblade lock
thingiverse
infinity lock beyblade
thingiverse
free
lock by alfredkim74
...lock by alfredkim74
thingiverse
desigm of an ergonomic and anthropometric lock
thingiverse
free
Lock by lilchamp
...lock by lilchamp
thingiverse
its a lock with my initials in the back
thingiverse
free
beer lock with 6mm lock hole by ruben_zilzer_3409
...beer lock with 6mm lock hole by ruben_zilzer_3409
thingiverse
same disign as bkahuna but for a bigger lock by