Thingiverse
Lightweight Dual to Single Extruder Conversion with Active Cooler for CTC / Flashforge by sndlover
by Thingiverse
Last crawled date: 3 years ago
This is a lightweight solution for converting the dual to a single extruder,
supporting the cables from being bent and incorporating a fan and air duct for object cooling.
It is recommended to print at least the top part and the nozzle in ABS.
Otherwise the top part tends to warp from motor heat (which is not a problem)
and the nozzle would probably warp too, being close to the extruder and heated bed.
All you need to complete the assembly are four 3mm screws, length 15mm to mount
the 40mm (standard or alternative) fan. You can either use self tapping PT screws or
Nylon screws for the ultimate weight saving experience (M3 tapping required).
The other two M3x40mm screws are the original.
The nozzle is a snug fit into the body and does not need any glue.
All parts are printed upside down!
Top part and nozzle are printed with 2 shells, 100% infill.
Body is printed with 2 shells, 15-20% infill.
Support is only recommended for the nozzle where it sits onn the aluminum bar.
No support inside the air ducts needed.
supporting the cables from being bent and incorporating a fan and air duct for object cooling.
It is recommended to print at least the top part and the nozzle in ABS.
Otherwise the top part tends to warp from motor heat (which is not a problem)
and the nozzle would probably warp too, being close to the extruder and heated bed.
All you need to complete the assembly are four 3mm screws, length 15mm to mount
the 40mm (standard or alternative) fan. You can either use self tapping PT screws or
Nylon screws for the ultimate weight saving experience (M3 tapping required).
The other two M3x40mm screws are the original.
The nozzle is a snug fit into the body and does not need any glue.
All parts are printed upside down!
Top part and nozzle are printed with 2 shells, 100% infill.
Body is printed with 2 shells, 15-20% infill.
Support is only recommended for the nozzle where it sits onn the aluminum bar.
No support inside the air ducts needed.
Similar models
thingiverse
free
DONOTUSE - Dual extruder dual radial fan holder by raf_ds
...id warping when the extruder is used without fan cooling.
chain is openable for easy servicing.
layerheight .15-.2 should be ok.
thingiverse
free
Double Extruder Fan Channel by ChrisX35
...ign fan that places the air duct in back of nozzle and has a support to prevent sagging. http://www.thingiverse.com/thing:1542849
thingiverse
free
Fan Duct for Raise 3D N2/N2+, Single Extruder by socke
...support needed for printing if you lay it on the surface where the fan is mounted. i printed mine with esun epc and 100% infill.
thingiverse
free
Replicator Dual Head Fan Duct by rhodeseng
...ints. in my experience this duct reduces the chances of large structural parts de-laminating, warping, bending etc as they print.
thingiverse
free
30mm Fan Shell to 5015 Cooling Duct by akf_was_here
...ey will double as integral supports. i'll update with the revised model if it elminates the need for supports when printing.
thingiverse
free
Mendel90 x-carriage hotend fan duct (always on, for hexagon hotend) by Stemer114
...the fan duct (towards the hotend) is for the extruder mounting to still be accessible when the duct is mounted (see 3rd picture).
thingiverse
free
Geeetech Prusa i3 pro extruder fan duct mkII by thegman
...er to join the 2 pieces together, manually.
i also tapped the holes for the m4 x 20mm screws that mount the 40mm fan to the duct.
thingiverse
free
E3D v6 Mount for DreamMaker OverLord by AFIF
..., and not the e3d upgrade parts from dreammaker. the heater block from dreammaker seems a bit larger, so your mileage may vary :)
thingiverse
free
Flashforge dual extrusion air duct by MakerUnit
...ooling fan and remove the one screw that holds the stock air duct. replace the air duct with the new one and reattach the screws.
thingiverse
free
Fan Duct for Raise3D N2 Dual Extruder Used As Single Extruder by OldRick
...and that clearances are tight. i moved the washers from outside the fan, to the left, inside the duct, to clear the cooling fins.
Sndlover
thingiverse
free
ZMR250 Landing Gear by sndlover
...mple but quite rigid landig gear for zmr250 and similar frames.
variants with 25mm / 30mm clearance and 2mm / 3mm mounting holes.
thingiverse
free
JST XH Balancer Plug Cap by sndlover
...jst xh balancer plug cap by sndlover
thingiverse
simple and easy printing cap for lipo balancer plugs of type jst-xh.
thingiverse
free
CTC / FlashForge Bowden PushFit Holder by sndlover
...ifferent fitting sizes in a bowden conversion with the original ctc / flashforge carriage.
note: i will add some m6 types later.
thingiverse
free
Bugaboo Buffalo Stroller Hook by sndlover
...m.
by snapping them over the existing screws, they self lock against slipping down.
printed in pla with 2 shells and 100% infill.
thingiverse
free
Bronze Bushing Sleeve for LM8SUU Replacement (CTC / FlashForge) by sndlover
...(flex) material with medium infill,
giving you a tight fit, but some freedom for the bushing to adapt to the rod without jamming.
thingiverse
free
Laboratory Power Supply To Go by sndlover
...use the bgsup_digaphragms instead of support. they will print a thin wall of one perimeter, leaving a 0.3mm gap around all sides.
thingiverse
free
Lightweight Dual to Single Extruder for Flashforge Creator Pro by antbarney
...screws to attach the body. most thanks go to @sndlover for the original...
thingiverse
free
CTC Bizer Single Extruder Cable Chain with Modified Part Cooler... by CTcartesian3D
...being level bugged me like crazy. cooler originally by sndlover - the cooler body and duct where a perfect...
thingiverse
free
Modified duct for lightweight blower by jmsjgill
...mine. i needed something a little more direct than sndlover#39;s design (http://www.thingiverse.com/thing:1336355) with the finesse of thruit00's design (http://www.thingiverse.com/thing:537918),...
Ctc
thingiverse
free
CTC by apone4
...ctc by apone4
thingiverse
modifica per ctc montaggio e3d
thingiverse
free
Filiamenthalter CTC by e2mars
...filiamenthalter ctc by e2mars
thingiverse
filiamenthalter ctc makebot
thingiverse
free
CTC's Feet by zion_taron
...ctc's feet by zion_taron
thingiverse
feet to ctc printers
thingiverse
free
CTC Abdeckung by Einstein77
...ctc abdeckung by einstein77
thingiverse
abdeckung für die hinteren bohrungen im gehäuse des ctc
thingiverse
free
CTC Corner caps by KyoFR
...ctc corner caps by kyofr
thingiverse
corner caps ctc
thingiverse
free
FILAMENT GUIDE CTC by HugoNogier
...filament guide ctc by hugonogier
thingiverse
filament guide ctc
thingiverse
free
CTC Bizer Fusshalter by FPV57
...ctc bizer fusshalter by fpv57
thingiverse
haltewinkel für gummifüsse ctc
thingiverse
free
CTC Cache motor by KyoFR
...ctc cache motor by kyofr
thingiverse
cache moteur pour imprimante ctc.
thingiverse
free
Dual extruder CTC by e2mars
...dual extruder ctc by e2mars
thingiverse
dual extruder für ctc 3d drucker
thingiverse
free
CTC door Latch by Docdaniel
...ctc door latch by docdaniel
thingiverse
simple ctc 3d/ replicator door latch
Lightweight
thingiverse
free
Lightweight Phone stand by Maverick1701
...lightweight phone stand by maverick1701
thingiverse
a lightweight phone stand i made.
thingiverse
free
Lightweight Maintenance Enclosure by Smprgumbi
...weight maintenance enclosure by smprgumbi
thingiverse
low res model of a military lightweight maintenance enclosure, or lme tent
thingiverse
free
lightweight 26cm light cover by krlehnardt
...lightweight 26cm light cover by krlehnardt
thingiverse
lightweight cover
thingiverse
free
bebop lightweight radiating base by mming1106
...bebop lightweight radiating base by mming1106
thingiverse
lightweight radiating base
thingiverse
free
Vape Holder Lightweight remix by mac190
...vape holder lightweight remix by mac190
thingiverse
lightweight remix of https://www.thingiverse.com/thing:2034257.
thingiverse
free
Lightweight tent peg / spike by Jaimon
...lightweight tent peg / spike by jaimon
thingiverse
a lightweight tent spike that is printable without any support!
thingiverse
free
Lightweight Herb Grinder by kylewetton
...
a lightweight, minimal design to ensure a quick 30 minute (or under) print! works great, 40mm diameter, stands about 15mm tall.
thingiverse
free
120mm fan grill lightweight Stern
...120mm fan grill lightweight stern
thingiverse
this is lightweight grill for 120mm fan.
all thin parts are about 1mm.
thingiverse
free
Lightweight canopee by Danotech
...lightweight canopee by danotech
thingiverse
lightweigt canopee fot tiny whoop.
resin printer recommended for this one
thingiverse
free
Lightweight Master Spool by Eoghan_ODuffy
... masterspool design. it only uses about 80g of filament.
spool needs to be tapped with an m6 hole and assembled using 3 m6 screws
Flashforge
thingiverse
free
Flashforge Logo
...flashforge logo
thingiverse
flashforge logo
thingiverse
free
flashforge logo by morive3d
...flashforge logo by morive3d
thingiverse
this is a flashforge stamphttps://www.youtube.com/channel/ucu6ge9qrju9cpgg6wrlxkqw
thingiverse
free
Flashforge Glass Bed by olo2000pm
...flashforge glass bed by olo2000pm
thingiverse
flashforge glass bed
thingiverse
free
Toolbox for FlashForge Finder by Gringo1970
...toolbox for flashforge finder by gringo1970
thingiverse
smal toolbox for flashforge finder
thingiverse
free
Flashforge / Dremel lid by Disco_Rob
...flashforge / dremel lid by disco_rob
thingiverse
lid extension for the flashforge dreamer
thingiverse
free
Flashforge Dreamer Filamentguide by PeterS1
...de for flashforge dreamer / dremel idea. you need also flashforge dreamer lid spacer (http://www.thingiverse.com/thing:1219953)
thingiverse
free
Flashforge creator legs by cybadigitals
...flashforge creator legs by cybadigitals
thingiverse
these legs gives a clearance of 25mm for flashforge creator series
thingiverse
free
Flashforge Inventor/Dreamer by Iprintr7
...orge inventor/dreamer by iprintr7
thingiverse
this is my first thingiverse project and is a model of the flashforge 3d printer
thingiverse
free
Flashforge Filiment Guide by russellscanlan
...flashforge filiment guide by russellscanlan
thingiverse
my design to feed filament through the door on a flashforge adventure 3
thingiverse
free
Flashforge Winder Adapter by newky2k
...winder adapter by newky2k
thingiverse
adapters for the flashforge 0.5 kg spools to the for the filament spool winder by ssinnott
Conversion
thingiverse
free
Converse keychain for Converse's fan by theletech
...converse keychain for converse's fan by theletech
thingiverse
please print in 0.15 or 0.2 for the best quality
thingiverse
free
Blockjacker arm conversion
...blockjacker arm conversion
thingiverse
a conversion for a giant robot. mirror to print l and r arms
thingiverse
free
Converse Shoes by spekdesign
...converse shoes by spekdesign
thingiverse
simple converse shoes (left + right) intended for small prints with minimal detail.
thingiverse
free
Conversation Hearts by PfLibrarian
...n hearts by pflibrarian
thingiverse
conversation hearts with three different candy heart phrases. great for valentine's day!
thingiverse
free
associated B4 conversion pancar
...associated b4 conversion pancar
thingiverse
associated b4 conversion pancar
thingiverse
free
Rotofury Elite Conversion by Hooliganblasterco
...rotofury elite conversion by hooliganblasterco
thingiverse
rotofury elite conversion, reversable
thingiverse
free
Conversation Hearts
... the heart instead of popped out. get creative if you like and fill the indents with paint or glitter and seal to make an impact!
thingiverse
free
Conversion Kit Box (Slide Conversion Kit) by Ziggi42
...nd tpu (buffers).
everything you have to know is in the readme.txt or look at print settings misc.
thanks and gimme a like!!!
sfo
thingiverse
free
BOOMBASTIC .22 CONVERSION by mussy
...boombastic .22 conversion by mussy
thingiverse
this is a .22 rim fire blank conversion... enjoy
thingiverse
free
20mm Fan conversion by fluxcore
...20mm fan conversion by fluxcore
thingiverse
conversion from a 20mm fan to a blower or extractor.......unfinished
Cooler
thingiverse
free
Cooler by DmitryErgman
...cooler by dmitryergman
thingiverse
keychain cooler with rotating screw
thingiverse
free
Simple J-heaad Cooler 50x50 cooler UPDATED
...simple j-heaad cooler 50x50 cooler updated
thingiverse
50x50, and 30x30 cooler for j-head, nozzle cooler
thingiverse
free
Cooler by jonspencer
...l and it had square duct work so i changed that in cooler 6. cooler 7 is for the port side, hopefully a mirror image of cooler 6
thingiverse
free
memory cooler
...memory cooler
thingiverse
cooler for pc memory using a 50mm fan,either blank or with hp with filler plate.
thingiverse
free
Fan Cooler by swdjojo
...fan cooler by swdjojo
thingiverse
fan cooler
thingiverse
free
Water Cooler by gfisher1
...water cooler by gfisher1
thingiverse
a water cooler
thingiverse
free
Cooler console by Scumari
...cooler console by scumari
thingiverse
a cooler console to cool your steppermotors.
for 40 and 50 mm coolers for quick use.
thingiverse
free
Cooler Keeper by MrKindergarten
...)
if someone comes up with a way to redesign the cooler keeper to add an additional function, such as a bottle opener, go for it!
thingiverse
free
phone cooler by ClownCorder1
...phone cooler by clowncorder1
thingiverse
a cooler for your phone
thingiverse
free
Fan cooler by Rustam
...fan cooler by rustam
thingiverse
fan cooler extruder
Active
thingiverse
free
swollen activity
...swollen activity
thingiverse
extracurricular activity
thingiverse
free
Activation Tokens
...activation tokens
thingiverse
country unit tokens 20mm, (activation tokens) used for seven day to the river rhine etc
thingiverse
free
Endstop Activity by peteruhlmann
...endstop activity by peteruhlmann
thingiverse
endstop activity
thingiverse
free
Activated Carbon Sploof by ThisWasntTaken
...p with the ring on top. then fill with activated carbon.
you can buy activated carbon in most pet stores in the aquarium section.
thingiverse
free
Activation Index by DarthDrakon
...activation index by darthdrakon
thingiverse
halo!!!!!!!!!!!!!!!!!!!!
thingiverse
free
Galaxy S5 Active by mattisj
...galaxy s5 active by mattisj
thingiverse
quick sketch up of a galaxy s5 active
thingiverse
free
knight activator by Dakanzla
...verse.com/thing:2865138
print 6 activators for each player
open design in tinkercad: https://www.tinkercad.com/things/iefck0hjdpj
thingiverse
free
Drawer Upgrade. by AcTiv
...drawer upgrade. by activ
thingiverse
drawer upgrade.
thingiverse
free
Simple activity board by CommanderGir
...simple activity board by commandergir
thingiverse
a simple activity board.
the gears lamp and holder for the pipes are printed.
thingiverse
free
Sploof (works with activated charcoal
...sploof (works with activated charcoal
thingiverse
this i a small sploof you put activated charcoal in and youre done
Dual
thingiverse
free
Dual 4010
...dual 4010
thingiverse
dual fan 4010
thingiverse
free
dual color cone for testing dual extruders by lovethepirk
...dual color cone for testing dual extruders by lovethepirk
thingiverse
dual color cone for testing dual extruders
thingiverse
free
Dual hook by duxdhell
...dual hook by duxdhell
thingiverse
dual hook
thingiverse
free
Headsetholder dual by J3M
...headsetholder dual by j3m
thingiverse
dual headset holder
thingiverse
free
Dual extruder by gustavorpinheiro
...dual extruder by gustavorpinheiro
thingiverse
this is a support for dual extruders.
thingiverse
free
Dual Plate by Jaimemarie
...dual plate by jaimemarie
thingiverse
toggle and dual outlet plate
thingiverse
free
Dual IEC by mrkrash
...dual iec by mrkrash
thingiverse
dual hotend with fine regulation
thingiverse
free
Dual Spinner by AidanSandersSAN
...dual spinner by aidansanderssan
thingiverse
a dual spinner i made in class.
thingiverse
free
Dual Spinner by groman
...dual spinner by groman
thingiverse
a quick remix of the tri spinner. a dual spinner!
thingiverse
free
Dual stepper mount
...dual stepper mount
thingiverse
dual stepper mount. drill mounting holes for printer
Single
thingiverse
free
single house by kallik
...single house by kallik
thingiverse
single house
thingiverse
free
single house by callsaul
...single house by callsaul
thingiverse
single house
thingiverse
free
SINGLE HOUSE by kallik
...single house by kallik
thingiverse
single house
thingiverse
free
SINGLE HOUSE by kallik
...single house by kallik
thingiverse
single house
thingiverse
free
SINGLE HOUSE by callsaul
...single house by callsaul
thingiverse
single house
thingiverse
free
SINGLE HOUSE by callsaul
...single house by callsaul
thingiverse
single house
thingiverse
free
wave single by Syzguru11
...wave single by syzguru11
thingiverse
wave single
thingiverse
free
Single House by nagato
...single house by nagato
thingiverse
single house
thingiverse
free
SINGLE HOUSE by nagato
...single house by nagato
thingiverse
single house
thingiverse
free
SINGLE HOUSE by leonk
...single house by leonk
thingiverse
single house
Extruder
thingiverse
free
Extruder
...extruder
thingiverse
extruder for 3dprinter
thingiverse
free
Linear extrude, rotation extrude by jtirado
...linear extrude, rotation extrude by jtirado
thingiverse
linear extrude, rotation extrude
thingiverse
free
extruder by brunoschoofs
...extruder by brunoschoofs
thingiverse
extruder
thingiverse
free
Extruder Catcher/Extruder Holder by Verdandi
...extruder catcher/extruder holder by verdandi
thingiverse
for holding extruder.
thx for clicking
designed on sketch up
thingiverse
free
extruder by nekro
...extruder by nekro
thingiverse
cooler extruder
thingiverse
free
Extruder by DViktor
...extruder by dviktor
thingiverse
extruder with three fans (1 unmanaged extruder and 2 managed to product) fans 20x20x10
thingiverse
free
Extruder Knob
...extruder knob
thingiverse
yet another extruder knob.
thingiverse
free
Extruder by ImHuman
...extruder by imhuman
thingiverse
my first extruder. my design.
thingiverse
free
BMG extruder
...bmg extruder
thingiverse
bmg extruder model : step, wrl, stl
thingiverse
free
Bowden Extruder
...bowden extruder
thingiverse
i have created bowden extruder for flsun delta 3d printer.