Thingiverse
LH Mount for Turbo Fan Duct, Taz5 by KillaCycle
by Thingiverse
Last crawled date: 3 years ago
Mount allows a Very nice fan duct to be mounted on a Taz5 (plus others).
Here is a link to the cooler duct:http://www.thingiverse.com/thing:1025471
The mount both adapts the duct with the fan on the left-hand side, and provides the necessary extension pad for the Y axis limit swtich. This keeps the stage from smashing the fan into the side of the structure when you home the Y-axis.
You have to drill a couple of holes in the underside of the stock extruder support body. You remove the extruder, put it upside down and hold it in position with some sort of softjawed vice, and position the mount with the duct attached on the extruder. You want to center the extruder hotend on the fan duct. you then drill with a #39 (2.5mm) drill through the hole in the center of the mount and into the extruder support. Tap that hole (or simply use the 3mm screw to form the threads) and tighten the screw. Take out the rear screw holding the duct to the mount, and drill and tap that hole in the extruder support. Replace the screw in the duct. Wire the fan up and remount the extruder and you are done.
This fan duct obscures your view of the part while it is printing, but makes absolutely gorgeous parts.
You run the fan to ~50% maximum near the bed. When the head gets up away from the bed you can run it to ~60%. You might wish to replace the 24volt 30W heater in your extruder with a 24volt 40W heater. You can then run the fan all the way up.
Here is a link to the cooler duct:http://www.thingiverse.com/thing:1025471
The mount both adapts the duct with the fan on the left-hand side, and provides the necessary extension pad for the Y axis limit swtich. This keeps the stage from smashing the fan into the side of the structure when you home the Y-axis.
You have to drill a couple of holes in the underside of the stock extruder support body. You remove the extruder, put it upside down and hold it in position with some sort of softjawed vice, and position the mount with the duct attached on the extruder. You want to center the extruder hotend on the fan duct. you then drill with a #39 (2.5mm) drill through the hole in the center of the mount and into the extruder support. Tap that hole (or simply use the 3mm screw to form the threads) and tighten the screw. Take out the rear screw holding the duct to the mount, and drill and tap that hole in the extruder support. Replace the screw in the duct. Wire the fan up and remount the extruder and you are done.
This fan duct obscures your view of the part while it is printing, but makes absolutely gorgeous parts.
You run the fan to ~50% maximum near the bed. When the head gets up away from the bed you can run it to ~60%. You might wish to replace the 24volt 30W heater in your extruder with a 24volt 40W heater. You can then run the fan all the way up.
Similar models
thingiverse
free
Geeetech Prusa i3 pro extruder fan duct mkII by thegman
...er to join the 2 pieces together, manually.
i also tapped the holes for the m4 x 20mm screws that mount the 40mm fan to the duct.
thingiverse
free
Hemera Mount and Cooling Duct for Ender 3
...e points to the original hole. the arrow at the bottom of the photo shows the bolt going into the new hole i tapped and drilled.
thingiverse
free
MakerFarm i3v Print Cooling Fan Mounts by charlieray
...ly drill out the holes for screws. in my case, i drilled out for m3 screws. some slight filing for an m3 nut trap for mounting.
thingiverse
free
part fan with probe by kth1022
...nd edited in tinkercad. to mount the fan duct you have to either tap the hole for the x axis bushing or use self tapping screws.
thingiverse
free
Lulzbot TAZ Fan Dual Duct with Tap ready holes by Makuna
... metal hot end for your taz4, then this modified fan duct is not needed as it has a separate fan that cools the hot end directly.
thingiverse
free
CubePro Blower Fan Duct by thingengineer
...e piece that extends to the far screw. i removed my second extruder as slicers have gotten so much better with supports now days.
thingiverse
free
Duplicator 4 Sidefans by Juhaur
...if you drill a 3mm hole in the heatsink at the same position as the hole on top of the ducts, you can use it to fasten the ducts.
thingiverse
free
Modified Extruder Mount and new Fan Duct for Hypercube Evolution by Asphyth
...: upload new fanduct, little flow optimisation, arms for the mount reinforced (2mm > 3mm), hole size bigger + cable lock added
thingiverse
free
Ender 3 40mm fan duct for parts cooling
...of the stock extruder housing. there are already some similar designs on thingiverse, but i moved the fan up...
thingiverse
free
Anet A6 Semi-circular Fan Duct by BrienAllison
...ght angle). i have also added a simple x-axis cable strain relief point to the bracket.
no supports are required for these parts.
Killacycle
thingiverse
free
Paintball Cylinder Cap by KillaCycle
...takes about half an hour to print using pla. it is always a bit of a challenge to make threads that work correctly. these do. :-)
thingiverse
free
Taz5 Bracket for DiiiCooler Duct by KillaCycle
... peer between the fan duct and the table.
(see my low profile heated bed tabs that you will also need if you install this duct.)
thingiverse
free
Low Profile Heated Bed Tabs by KillaCycle
...aching it. rest the duct on three of these tabs and tighten the screws. your diicooler duct will be level and the correct height.
thingiverse
free
Dishwasher Basket for Silverware and CHOPSTICKS! by KillaCycle
...file. the grate extrusions are "delicate". if you attempt resize the bars, etc. they tend to fail. (ask me how i know.)
thingiverse
free
Heated 3D Printer Enclosure by KillaCycle
...it in the last picture. you can use a very compact 120vac space heater with a built-in thermostat instead if you are on a budget.
thingiverse
free
M-33 V-belt for Mitsubishi DB-130G Sewing Machine by KillaCycle
...o fit it, however, but it is near the minimum range for the adjustment.
inventor 2018 file included so you can change the length.
thingiverse
free
Overhead Filament Spool Holder (Lulzbot Taz) by KillaCycle
... nuts wedged in the center slot in the printer rail. seems to work fine for us just resting on the rails without screws, however.
thingiverse
free
Digital Dial Indicator/Caliper Connector with Built-in Level Shifter by KillaCycle
...this connector on masterkookus' thingiverse post, and learn how to wire up the level shifter on wel-hsiung huang's blog.
thingiverse
free
Taz replacement 25mm hotend Fan Duct by KillaCycle
...ut abs would work as well. pla or hips would likely soften or melt in use, but you could try it if that is what you have on hand.
Taz5
thingiverse
free
Lulzbot Taz5 Enclosure by drandolph
... access to a laser cutter you can purchase a kit that includes everything except the 3d printed parts at https://printedsolid.com
thingiverse
free
Taz5 BLTouch Mount by zanthor
...ide of your extruder to anchor this. i ran the bolt through the original nut and then captured the bltouch mount with a 2nd nut.
thingiverse
free
TAZ5 Low Friction Spool Holder by uCHobby
...
the pictured was printed with lulzbot natural pla at 205c on pei bed at 60c, at 60mm/s and 0.2 layer height with a 0.5mm nozzle.
thingiverse
free
TAZ5 y_bearing_mount_v2.6.mod.STL by ARC7217
...verse
i kept having the y axis idler bearing mount crack, so this is an attempt to beef up the weak point on the bearing holder.
thingiverse
free
E3D V6 Adapter Plate for TaZ5 by iporty
.... the extra channels were to reduce weight. i made my version out of aluminum, but i think a 3d printed one would work well also.
thingiverse
free
Lulzbot TAZ5 to Mini adapter by wrvn97
...rse
simply install this adapter on your taz, then install the mini toolhead. easy as that (though it may take some calibration)!
thingiverse
free
Left Fan hidden mount for taz5 by MorganCoLLC
...an hidden mount for taz5 by morgancollc
thingiverse
the bolt can be tightened by placing the allen wrench threw the air out port
thingiverse
free
Taz5-6 Stepper Encoder
...m of the gear. stick the white leader on first and then wrap it around.
the board is available through oshpark.com
cheer
kisssys
thingiverse
free
TAZ5 Hot End Duct for 25 mm Fan by mtgansler
...5 hot end duct for 25 mm fan by mtgansler
thingiverse
shortened it a bit for easier installation and potentially better airflow.
thingiverse
free
Lulzbot TAZ5 7 SD Card Holder by Springloadedexploded
... by springloadedexploded
thingiverse
this is a 7 card holder for a lulzbot taz 5 printer, though i think it will also fit the 4.
Lh
thingiverse
free
Vive LH mount
...vive lh mount
thingiverse
vive light house mount
thingiverse
free
Multimeter_Holder BIG LH by neo777
...multimeter_holder big lh by neo777
thingiverse
remix of thing:2091206
thingiverse
free
rc-msr-x heli LH mold by vawt
...rc-msr-x heli lh mold by vawt
thingiverse
rc-msr-x heli lh mold
thingiverse
free
Hydra 5010 LH 35 with BL mount by cytoe1
...hydra 5010 lh 35 with bl mount by cytoe1
thingiverse
sloppily added the bl mount to the lh 35 deg duct
thingiverse
free
Dacre Station LHS building by georgeswilson
...dacre station lhs building by georgeswilson
thingiverse
updated with more detail
thingiverse
free
LH VR Camera Mount by jclpld
...lh vr camera mount by jclpld
thingiverse
a mount to mount a vr camera to a cart
thingiverse
free
Key knob by sat-lhs
...y sat-lhs
thingiverse
this knob can be equipped with a key. with the knob, the key can be turned in the lock without any effort.
thingiverse
free
LHS key chain by bdoggy45
...
thingiverse
this is an original design i made for my school. there is some room for improvement but i like how it is right now.
thingiverse
free
Tarantula fan duct LH REMIX by Brandonmh83
...tarantula fan duct lh remix by brandonmh83
thingiverse
here is the stl you wanted.
thingiverse
free
LH Z End Stop for i3 Mega Ultrabase by Rednov
...ront). if you have a machine with dual z limit switches then you will need one of these in addition to the original file. cheers!
Turbo
thingiverse
free
Turbo by MrsBecraft
...turbo by mrsbecraft
thingiverse
turbo for car
thingiverse
free
Turbo by pugboi
...turbo by pugboi
thingiverse
made by my friend.
thingiverse
free
Turbo jet by The_LAB
...turbo jet by the_lab
thingiverse
turbo jet
thingiverse
free
Turbo compressor by marco0030
...turbo compressor by marco0030
thingiverse
just a turbo compressor
thingiverse
free
Turbo Supra by william3d
...turbo supra by william3d
thingiverse
turbo supra letters
thingiverse
free
turbo fan by felix727144
...turbo fan by felix727144
thingiverse
a turbo fan.
3mm
thingiverse
free
twin turbo snail
...twin turbo snail
thingiverse
just a snail with some turbos for shell
thingiverse
free
Turbo-Bowl: Turbo-Vase+, the Sequel Continues by jaln
...the sequel continues by jaln
thingiverse
here's some matching bowls for vase10a.
(turbo-vase+, the sequel).
scaled 1x and 2x
thingiverse
free
Turbo Impeller by Thalmano
...turbo impeller by thalmano
thingiverse
turbo impeller
hook it up to an e-motor and have fun
thingiverse
free
Turbo fins by print3dXYZ
...turbo fins by print3dxyz
thingiverse
turbo fins designed to fit standard fcs plugs. work great on a bodyboard
Duct
thingiverse
free
NACA Duct to 3inch Hose for duct & brakes
... & brakes
thingiverse
naca duct to 3inch hose for duct & brakes
as seen here:https://www.youtube.com/watch?v=nrv6kayzwkw
thingiverse
free
Donut duct
...donut duct
thingiverse
after breaking the original ducts, i developed my own, stronger
thingiverse
free
Duct-to-duct Adapter (4-inch to 6-inch)
...ry: 97.0 mm
outer diameter for 6inch duct entry: 156.0 mm
inner diameter for 6inch duct entry: 153.0 mm
enjoy printing!
curiousor
thingiverse
free
Fan Duct by JacobMakes
...fan duct by jacobmakes
thingiverse
a fan duct
thingiverse
free
Fan Duct by CodyG
...fan duct by codyg
thingiverse
fan duct
thingiverse
free
Fan Duct by CodyG
...fan duct by codyg
thingiverse
fan duct
thingiverse
free
5015 fan duct
...5015 fan duct
thingiverse
5015 fan duct
thingiverse
free
Duct Vortex V1
...duct vortex v1
thingiverse
duct vortex v1
thingiverse
free
ducted fan by LorenzjP
...ducted fan by lorenzjp
thingiverse
ducted fan assembly
thingiverse
free
Cable duct by prokazzza
...cable duct by prokazzza
thingiverse
cable duct for wire routing.
Fan
thingiverse
free
Fan Duct 60mm fan
...fan duct 60mm fan
thingiverse
this a 60mm fan adaptor
thingiverse
free
Fan Stand 140mm Fan by Aron84
...fan stand 140mm fan by aron84
thingiverse
fan stand for 140x140x27mm fan
thingiverse
free
Fan wall for 40mm fan by Nule
...fan wall for 40mm fan by nule
thingiverse
fan aislator for 40mm fan with meshmixer support
thingiverse
free
Fan holder 40mm fan for V67
...n for v67
thingiverse
fan holder 40mm fan for v67
fan: https://www.amazon.de/dp/b07vhmv4dz/ref=cm_sw_r_other_apa_i_803cebwt8kvpe
thingiverse
free
Fan cover & fan grill to suit 50mm fan by Phil_Maddox
...fan cover & fan grill to suit 50mm fan by phil_maddox
thingiverse
simple fan cover for 50 x 50 x 10 fan
thingiverse
free
Fan grille for 50mm fan andE3D V6 Fan Duct for 50mm Fan V2 by vitaly12
...for 50mm fan ande3d v6 fan duct for 50mm fan v2https://www.thingiverse.com/thing:4662850
height:3.5mm
40mm fan grille coming soon
thingiverse
free
Fan Grid for 127mm Fan by MasterFX
...fan grid for 127mm fan by masterfx
thingiverse
just a simple fan grid for unusual 127mm fan
thingiverse
free
Fan Showdown fan submission by DAraymond
...fan showdown fan submission by daraymond
thingiverse
this is a fan i submitted for the youtube fan showdown series.
thingiverse
free
Fan Shroud
...fan shroud
thingiverse
this is a fan shroud for a 140mm fan
thingiverse
free
Mosaic Fan on Fan by bwevans
...a fan mount for the second fan that's included in the mosaic kit but is lacking any hardware. really useful for printing pla!
Mount
thingiverse
free
Pen Mount on BLTouch mount by jetspot
...pen mount on bltouch mount by jetspot
thingiverse
pen mount on bltouch mount
thingiverse
free
RAM Mount, Mount by seanmclean
...ram mount, mount by seanmclean
thingiverse
bridging plate to attach ram mount to yamaha 242, for chartplotter placement.
thingiverse
free
Mount for mount for Garmin GPS by GNOBLIN
...you can use this mount for prevent rotation simple mount around hendelbars.
d handelbar 31.8mm
use m3 screw and din 16903 plug.
thingiverse
free
Permanent mount for Modular Mounting System by WIR14
...permanent mount for modular mounting system by wir14
thingiverse
permanent mount for modular mounting system.
thingiverse
free
Gopro Mount and antenna mount by SuperYoyo
...gopro mount and antenna mount by superyoyo
thingiverse
cut the carbon platform to pass the gopro mount and enjoy !
thingiverse
free
Hexagon Mount for 50mm Mount (Sparkcube) by Draman
...for 50mm mount (sparkcube) by draman
thingiverse
hexagon mount remix from skimmys hotend-mount for sparkcube or other 50mm-mount
thingiverse
free
mount by gixster
...mount by gixster
thingiverse
custom mount
thingiverse
free
Mount by Matrxi999
...mount by matrxi999
thingiverse
shelf mount
thingiverse
free
Motor mount
...motor mount
thingiverse
motor mount
thingiverse
free
GoPro Mount
...gopro mount
thingiverse
gopro mount