Thingiverse
Lathe Index Wheel by Terminus
by Thingiverse
Last crawled date: 2 years, 12 months ago
Used as a protractor, it allows you to divide a work piece.
Instructions
I had an old Atlas lathe with one of these degree wheels on the back of the chuck, used it often and now I miss it. So I made one for this mini lathe.
The 4 inch diameter wheel has a hole every 5 degrees. I designed it with zero-clearance and, as a result, it is conveniently attached by a tight slip-fit over a spindle retaining nut on the rear of the spindle.
The pointer bracket is just a basic pointer-holder at this time. I'm not quite sure how or where I want to attach the pointer thing. A short length of aluminum rod is shown.
Both parts were "test" printed with Afinia default settings (basically medium speed and 0.30mm Z-resolution) and came out better than expected, so that's good enough for now.
The ring's small holes were well defined and surprisingly it showed no signs of warping or of wanting to lift. Perhaps that part is due to the relief I gave it. I did use a raft.
The bracket doesn't need a raft since only a small area touches the build platform, and to conserve filament I did not use one there.
Roughly 30g for the ring and 18g for the bracket.
Since the lathe's gear case cover must be removed to use this device, I used its two threaded attachment holes to bolt the pointer-bracket on with a couple of short 5mm x 0.80 bolts.
These lathes are regularly modified by the factories with slight differences season to season, and there's no telling if this thing will fit anyone's 7X mini lathe, but I suspect it very often will.
[Update]
Metric files have been provided, around Dec, 2016 so... Merry Christmas, Happy holidays
Instructions
I had an old Atlas lathe with one of these degree wheels on the back of the chuck, used it often and now I miss it. So I made one for this mini lathe.
The 4 inch diameter wheel has a hole every 5 degrees. I designed it with zero-clearance and, as a result, it is conveniently attached by a tight slip-fit over a spindle retaining nut on the rear of the spindle.
The pointer bracket is just a basic pointer-holder at this time. I'm not quite sure how or where I want to attach the pointer thing. A short length of aluminum rod is shown.
Both parts were "test" printed with Afinia default settings (basically medium speed and 0.30mm Z-resolution) and came out better than expected, so that's good enough for now.
The ring's small holes were well defined and surprisingly it showed no signs of warping or of wanting to lift. Perhaps that part is due to the relief I gave it. I did use a raft.
The bracket doesn't need a raft since only a small area touches the build platform, and to conserve filament I did not use one there.
Roughly 30g for the ring and 18g for the bracket.
Since the lathe's gear case cover must be removed to use this device, I used its two threaded attachment holes to bolt the pointer-bracket on with a couple of short 5mm x 0.80 bolts.
These lathes are regularly modified by the factories with slight differences season to season, and there's no telling if this thing will fit anyone's 7X mini lathe, but I suspect it very often will.
[Update]
Metric files have been provided, around Dec, 2016 so... Merry Christmas, Happy holidays
Similar models
thingiverse
free
Dog Wheel Chair Adjustable Bracket Prototype by gszczyrbak
...s really well. using the existing bolt hole designed for the strap support is nice too since it keeps the costs exactly the same.
thingiverse
free
360 degree indexing wheel for degree marking by Schtimpy
... edge was on centre of the pin. by doing this, i ensured that all indexing positions were at the same height/along the same line.
thingiverse
free
Bracket for Attachment of Caliper to Mini Lathe Carriage by MakerMarc
...on of the assemblyamazon link for the caliper
please read instructions for printing.
likes, makes and comments are appreciated!
thingiverse
free
Shop Vac Replacement Wheel by mikesshopworks
...ust used a bolt with a locking nut to attach it to the spindle.
simple design but has been working perfectly for over a year now.
thingiverse
free
Monoprice Select Mini pi camera mounting bracket by stevepax
...e.com/thing:247590
with a few more m3 bolts and nuts, it's all put together. solid, so it doesn't shake as the bed moves.
thingiverse
free
Corner bracket with hole by AlphaExile
...the only attachment point was in the corner between the mirrors. i could not find a bracket to match my needs so i designed this.
thingiverse
free
Kossel XL / Ultibots D300VS Corner Brace by disoculated
...ching the bracket to the frame.
image shows bolts unscrewed just to show one possible arrangement.
sketchup source file included.
thingiverse
free
Spacer for mini lath spindle. by 1911ly
...it is to long you can file/sand or cut it shorter if you use 100% infill. i have used this on 2 spindles and it worked perfectly.
thingiverse
free
FLSun i3 Xaxis Upgrade Decoupler Upgrade by RobbyMaQ
...ing for retension?)
i've also added spacing sleeves if one wishes to use their existing decouplers, and just add the spacers.
thingiverse
free
135 Degree Angle Brackets for 20mm Extrusions by roosevelt155
...a cutoff saw and a carbide blade. holes are designed for m4 bolts to be threaded into but a drill can be used to widen the holes.
Terminus
thingiverse
free
garrus terminus armor
...garrus terminus armor
thingiverse
fixed static garrus in terminus armor, with and without the helmet
thingiverse
free
Funnel by Terminus
...funnel by terminus
thingiverse
a funnel to fit gallon water bottles.
thingiverse
free
Ravioli Pin by Terminus
...ravioli pin by terminus
thingiverse
a simple pin, but it works.
thingiverse
free
rocket remix by Terminus
...rocket remix by terminus
thingiverse
rocket by jjbtexas remix
thingiverse
free
soldering station by Terminus
...soldering station by terminus
thingiverse
a compact soldering station
thingiverse
free
Pellets .177 by Terminus
...pellets .177 by terminus
thingiverse
plastic air rifle pellets
thingiverse
free
Lid rack by Terminus
...lid rack by terminus
thingiverse
anti-sloppy-kitchen device.
thingiverse
free
Coffee dispenser by Terminus
...coffee dispenser by terminus
thingiverse
cabinet mount coffee dispenser.
thingiverse
free
Microswitch hack by Terminus
...microswitch hack by terminus
thingiverse
turn a microswitch into an on / off switch.
thingiverse
free
Dough docker by Terminus
...dough docker by terminus
thingiverse
a dough docker for making indentations in dough.
Lathe
thingiverse
free
Mini Lathe - Egg Lathe by robertopaoli
...e to decorate things spherical.
speed variator pwm and double switch to reverse direction of rotation.
button for small advances.
thingiverse
free
lathe plug
...lathe plug
thingiverse
plug for back side of mighty turn lathe to stabilize 1.5" square stock
thingiverse
free
Wheel for lathe by Andrew1978
...wheel for lathe by andrew1978
thingiverse
wheel for lathe
thingiverse
free
Mini lathe by janblo
...mini lathe by janblo
thingiverse
wip mini lathe
thingiverse
free
Lathe Faceplate for 9x20 lathe by DasWookie
...ions:
dovetails are 12 degree and 25mm wide
mounting bolts are m6x1
centering rings are at 50, 100, and 150mm
center hole is 25mm
thingiverse
free
Lathe tool holder
...lathe tool holder
thingiverse
holder for small lathe tools
thingiverse
free
MINI-LATHE PROTECTION
...mini-lathe protection
thingiverse
protection and guide for mini-lathe
thingiverse
free
Homemade Lathe by comanderxv
...homemade lathe by comanderxv
thingiverse
this will be a lathe with parts of a cordless screwdriver.
thingiverse
free
Mini Lathe - Egg Lathe - New tailstock to 3 points. by robertopaoli
...lathe - egg lathe - new tailstock to 3 points. by robertopaoli
thingiverse
new tailstock to 3 points for mini lathe - egg lathe.
thingiverse
free
Lathe Parts by Muxlo
...lathe parts by muxlo
thingiverse
small cones for turning small objects in a lathe.
Index
thingiverse
free
Indexing head
...indexing head
thingiverse
indexing head, i used this with a spring on the screw so i could index it on the go.
thingiverse
free
index by ungjeffr
...index by ungjeffr
thingiverse
the index of my avl tree
thingiverse
free
Index Feed by joestraws
...index feed by joestraws
thingiverse
index feed.
thingiverse
free
Index Arm by joestraws
...index arm by joestraws
thingiverse
index arm guide. support structure needed.
thingiverse
free
Valve Index "Brocessor" Visor
...or" visor
thingiverse
a remix of the stock index visor, to commemorate the 2019 holidays index order spreadsheet community.
thingiverse
free
Valve Index mounting hook
...valve index mounting hook
thingiverse
mounting hook for valve index
thingiverse
free
Drill index by redcat
...hingiverse
this is another index for drill bits. includes number on front for identification. missing numbers are for half sizes
thingiverse
free
Index Splint by Dimide
...me cleaning !
designed this splint for my index so my index would not hit anything.
hope this can helps someone else in the need.
thingiverse
free
Metric Reamer Index by urw
...metric reamer index by urw
thingiverse
a quick index for my cheap set of metric reamers
thingiverse
free
Activation Index by DarthDrakon
...activation index by darthdrakon
thingiverse
halo!!!!!!!!!!!!!!!!!!!!
Wheel
thingiverse
free
power wheels wheels
...power wheels wheels
thingiverse
wheel for a power wheels 9 inches in diameter
thingiverse
free
wheel
...wheel
thingiverse
wheel
thingiverse
free
wheel
...wheel
thingiverse
wheel
thingiverse
free
The Wheel, Wheel by duemosy
...iverse
wheel wheel for maker's muse design challenge
the scaling is a little weird, had to scale to 50% for it to look right
thingiverse
free
wheel
...wheel
thingiverse
wheel thingi
thingiverse
free
Wheel
...wheel
thingiverse
wheel made in fusion360
thingiverse
free
Wheel
...wheel
thingiverse
wheel of toy car
thingiverse
free
wheel
...wheel
thingiverse
toy car wheel
thingiverse
free
Wheel
...wheel
thingiverse
some wheel model.
thingiverse
free
Wheels, wheels, wheels by IronOxide
...width is limited
only one spoke style
round axle is the only option at this time
code thrown together quickly - not the prettiest