Thingiverse
Large Spool Roller(s) by 3dAl
by Thingiverse
Last crawled date: 3 years ago
So you so you don't have to go running all over the place I will provide all the parts that I used. I made two large spool rollers. The bearings, rod and shaft collars and aluminum tube I ordered from the large online retailer Am*$on (Amazon), because I am lazy. You need:
(1) 8 Bearings 608ZZ 8x22x7 pre-greased
(2) 8mm shaft 30"
(3) Aluminum 6061-T6 Seamless Round Tubing, WW-T 700/6, 1" OD, 0.87" ID, 0.065" Wall,
(4) 4 or 8 8mm ID Shaft Collars
After printing the STL for either a single or dual, cut the aluminum tubing just a little shorter than the inside measurement of the Spool Holder but tight enough so the edge of a spool can fall into. Next take a bearing and clean the outer edge. Take some clear Scotch Tape and make one turn around the outside (see photos). This serves as a shim and also to keep super glue out of the bearing. Next use some gap filling (thick) super glue and run a small bead around the inside of the aluminum tube. Fold or taper the Scotch Tape so you can insert the bearing without getting glue on the bearing. Push bearing in, just flush or just protruding a little if you have the room. Do all tubes the same way then leave overnight to let the glue dry. Assemble by cutting the 8mm shaft to the correct length (don’t forget to add the length of two collars).
Assemble and use.
(1) 8 Bearings 608ZZ 8x22x7 pre-greased
(2) 8mm shaft 30"
(3) Aluminum 6061-T6 Seamless Round Tubing, WW-T 700/6, 1" OD, 0.87" ID, 0.065" Wall,
(4) 4 or 8 8mm ID Shaft Collars
After printing the STL for either a single or dual, cut the aluminum tubing just a little shorter than the inside measurement of the Spool Holder but tight enough so the edge of a spool can fall into. Next take a bearing and clean the outer edge. Take some clear Scotch Tape and make one turn around the outside (see photos). This serves as a shim and also to keep super glue out of the bearing. Next use some gap filling (thick) super glue and run a small bead around the inside of the aluminum tube. Fold or taper the Scotch Tape so you can insert the bearing without getting glue on the bearing. Push bearing in, just flush or just protruding a little if you have the room. Do all tubes the same way then leave overnight to let the glue dry. Assemble by cutting the 8mm shaft to the correct length (don’t forget to add the length of two collars).
Assemble and use.
Similar models
thingiverse
free
Complete Dry Box V2 by 3dAl
...round
(7) a desiccant box of your choice (i have included one above)
(8) a plastic box that seals well (see photo of what i used)
thingiverse
free
Dry Box for Large Spools with Roll Base by 3dAl
...aft.
(7) a desiccant box of your choice (i have included one above)
(8) a plastic box that seals well (see photo of what i used)
thingiverse
free
Monoprice Select Mini Spool Roller Shaft - 8mm ends by steelmesh
...meter 15 mm
max. spool width 80 mm
over all length 94 mm
also included full 8 mm x 95 mm thin shaft just in case you needed one.
thingiverse
free
Bearing Spool Rollers
... add the bearings on. i found setting a simple timer for 10 mins was enough to remind me, but you could add some code to stop it.
thingiverse
free
Large Spool Holder Wall mount
.... the bearings are typical skateboard wheel bearings. dimensions are outer diam. 22mm x 7mm x 8mm. roller shaft is 120mm x 7.8mm.
thingiverse
free
Spool Roller X by ehj
...lt; 22mm, diameter inside 8mm and a thickness of >= 8mm)
modify in freecad if you have different parts laying around.
success.
thingiverse
free
Easy roller spool rack by gghouck
... for either 6mm or 8mm id. to build, you will need 4 bearings, 4 tabs that fit your bearings, 1 base, and 1 of each of the tubes.
thingiverse
free
Filament Roller for large spools or reels by ELAD_ENGINEERING
...der than that and you will have a hard time fitting the bearings - 608 (22mmod,8mmid,7mmwide).
an 8mm shaft is essential as well.
thingiverse
free
Basic Spool Holder Center for 8mm Shaft by NatFaust
...ls with 2" (or, really, around 52mm) or smaller center holes. the actual diameter of the largest part of the holder is 58mm.
thingiverse
free
Spool Holder Extra large Stand Alone
...gs. dimensions are outer diam. 22mm x 7mm x 8mm. roller shaft is 120mm x 7.8mm. you will need to lay b & c flat on print bed.
3Dal
thingiverse
free
Desiccant Box by 3dAl
...siccant that you find in gallon jars on amazon. the slots are 2.5 mm so any desiccant larger that that will work.
for dry box
thingiverse
free
Lid for GoPro retail box by 3dAl
... camera and all the accessories so i decided to print one. it is large enough to hold the camera, all the accessories plus more.
thingiverse
free
Desiccant Tube by 3dAl
...model stronger and a little clearer. clear pla might work but i did not have any to try. i hope someone else finds this useful.
thingiverse
free
Glass Plate Holder by 3dAl
...rame pieces down. this is my first project using 123d design by autodesk (free), so it may not be perfect, but it worked for me.
thingiverse
free
Improved trigger for mini Crossbow by 3dAl
...;-3/16" sticks though the other side. carefully heat the end and form it like a rivet.
i think you will like this trigger
thingiverse
free
More Holey Desiccant Tube
...- share alike (cc by-sa 3.0) by poikilos and 3dal based on desiccant tube by 3dal nov 30,...
thingiverse
free
One piece arm for PL2Q Hugin Quadcopter by 3dAl
...uple of bands (not that any ever broke. i also created one without mounting holes for those that have different kinds of motors.
thingiverse
free
Complete Dry Box V2 by 3dAl
...round
(7) a desiccant box of your choice (i have included one above)
(8) a plastic box that seals well (see photo of what i used)
thingiverse
free
Dry Box for Large Spools with Roll Base by 3dAl
...aft.
(7) a desiccant box of your choice (i have included one above)
(8) a plastic box that seals well (see photo of what i used)
Roller
turbosquid
$26
Roller A
...urbosquid
royalty free 3d model roller a for download as fbx on turbosquid: 3d models for games, architecture, videos. (1350603)
turbosquid
$3
Roller
...oyalty free 3d model roller for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1460818)
3ddd
$1
edilkamin roller
...edilkamin roller
3ddd
камин
edilkamin roller 360
3ddd
$1
Roller Blinds
...roller blinds
3ddd
рулонная
roller blinds black out finish
turbosquid
$50
Roller
... roller for download as max, max, c4d, max, max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1700762)
3d_export
$10
rollers
...lers
3dexport
this is low-poly model of rollers.<br>model:<br>- low-poly<br>- textured<br>- uv unwrapped
3d_export
$28
Roller 3D Model
...roller 3d model
3dexport
roller construction boss evil
roller 3d model adagio15740837 50561 3dexport
3d_export
$6
hopper roller conveyor
...hopper roller conveyor
3dexport
hopper roller conveyor
3d_export
$12
roller skates
...roller skates
3dexport
3d_ocean
$19
roller skate
...can scanned skates skating sport
3d scan of roller skate. the model has been retopologized and made fully compatible with zbrush.
Spool
3ddd
$1
spool c53301
...spool c53301
3ddd
spool
spool c53301 650х350х145
turbosquid
$3
Cable Spool
...royalty free 3d model cable spool for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1457009)
turbosquid
free
Pallets and Spool
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Spool of String
...ol of string pink for download as c4d, 3ds, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1647892)
3ddd
$1
Подвесные светильники Spool
...ye/podvesnoy_svetilnik_spool_d320/ http://www.cosmorelax.ru/catalog/podvesnyye/podvesnoy_svetilnik_spool_d420/
3ddd
free
Spool 001 sofa
...spool 001 sofa
3ddd
roda
roda
collection spool
design rodolfo dordoni
dimensions:
lenght 90 cm
depth 94 cm
height 79 cm
turbosquid
$15
Roda Spool Sofa
...ee 3d model roda spool sofa for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1502650)
turbosquid
$95
wire spools 3ds
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
spool of TV wire
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$3
Simple and Fast Spool Holder
...ree 3d model simple and fast spool holder for download as stl on turbosquid: 3d models for games, architecture, videos. (1548546)
Large
3d_export
$15
large excavator
...large excavator
3dexport
large excavator
design_connected
$22
Daydream large
...daydream large
designconnected
dedon daydream large computer generated 3d model. designed by frinier, richard.
design_connected
$7
Laccio Large
...laccio large
designconnected
knoll laccio large computer generated 3d model. designed by breuer, marcel.
3ddd
$1
MOLTENI LARGE
... подушка , плед
диван molteni&c; модель large
3ddd
$1
Molteni Large
... подушка , плед
диван molteni&c; модель large
3ddd
$1
CLAUDINE LARGE
...audine large
3ddd
claudine large , arflex
модель сделана в размерах и цветах аналога ...
design_connected
$11
Ovo Large
...ovo large
designconnected
cor ovo large armchairs computer generated 3d model. designed by studio vertijet.
design_connected
$4
Cu Large
...cu large
designconnected
kristalia cu large coffee tables computer generated 3d model. designed by monica graffeo.
3d_ocean
$18
Large sausage
...rge meat mental ray obj photorealistic sausage scanned vray
scanned 3d model of large sausage placed on rectangular wooden board.
design_connected
$16
Filly Large
...onnected
photo-realistic 3d models of the filly large chair from bonaldo for 3d architectural and interior design presentations.