Thingiverse
Kossel MK2Y (220mm) heat bed clips by Simonwlchan
by Thingiverse
Last crawled date: 3 years ago
Clips to secure a 22cm diameter heat bed to the Kossel Mini's frame. 5mm lip holds the set up securely without getting too close to the effective heated area.
This hold a 19mm high "sandwich" comprising of (bottom up):
-- 3mm thick borosilicate glass (22cm dia.)
-- 11.5mm thick cork board (IKEA HEAT @ 20cm dia. - not sure of fire rating though)
-- 1.5mm MK2Y 200 heat bed
-- 3mm thick borosilicate glass (22cm dia.)
5mm clearance at the base allows elevation away from the electronics underneath although the cork board should insulate the heat.
This is WIP, I've no intention to power up the heat bed any time soon (there is a RAMPS problem anyway) so I would likely add a layer of kapton between the bed and cork board for added safety.
The 3 clips are locked in place by 3 x 30mm M3 hex pipes. I replaced the short M34 top screw with a M38mm. Added 6 M3*8 screws to lock the top plate in place.
Installation:
Install 3 base units, place one piece of glass, adjust then tighten base pieces.
Install cork board (notice I grooved it to accommodate the thermistor cable so it all sits flat)
Loosen ONE base unit, install heat bed and top glass
Re-fasten the base unit.
GENTLY tighten dual M3*8 screws on all three top plates (don't over tighten or you might break or stress the glass or your print, whichever is weaker).
For removal to access printer innards loosen one base unit.
This hold a 19mm high "sandwich" comprising of (bottom up):
-- 3mm thick borosilicate glass (22cm dia.)
-- 11.5mm thick cork board (IKEA HEAT @ 20cm dia. - not sure of fire rating though)
-- 1.5mm MK2Y 200 heat bed
-- 3mm thick borosilicate glass (22cm dia.)
5mm clearance at the base allows elevation away from the electronics underneath although the cork board should insulate the heat.
This is WIP, I've no intention to power up the heat bed any time soon (there is a RAMPS problem anyway) so I would likely add a layer of kapton between the bed and cork board for added safety.
The 3 clips are locked in place by 3 x 30mm M3 hex pipes. I replaced the short M34 top screw with a M38mm. Added 6 M3*8 screws to lock the top plate in place.
Installation:
Install 3 base units, place one piece of glass, adjust then tighten base pieces.
Install cork board (notice I grooved it to accommodate the thermistor cable so it all sits flat)
Loosen ONE base unit, install heat bed and top glass
Re-fasten the base unit.
GENTLY tighten dual M3*8 screws on all three top plates (don't over tighten or you might break or stress the glass or your print, whichever is weaker).
For removal to access printer innards loosen one base unit.
Similar models
thingiverse
free
Quick release bed clip for kossel delta by uhruh
... x 5mm)
m3 bolt and nut
sorry.
the first uploaded clamp geometry was updated incorrectly.
corrected due to missing rotation axis.
thingiverse
free
Glass clamp and heat bed for Mini Kossel by micolo
... on parate project. i used 1mm aluminium only on top and other "layers" was cut from laminate (1mm thick) and 2mm cork.
thingiverse
free
Anycubic Kossel Linear Plus 240mm insulated heated bed mount by tjko
...is 5.5mm so if using 5mm cork board as insulation, there is space to add layer of kapton tape in between the heater and the cork.
thingiverse
free
FolgerTech - FSR Mount for Heated Bed by Walt750
...ct to give the best sensitivity.
this is my first printer, first drawing, first everything....
designed on designspark mechanical
thingiverse
free
Build Plate Mount for Anycubic Kossel Plus 240mm Glass Plate by r_k
... anycubic kossel plus with a 240mm glass plate
added 3mm extra space for the 220mm mk3 heatbed
new version with 5mm screw holes
thingiverse
free
200mm Borosilicate glass holder for Folgertech Kossel (or any 220mm heating bed) by damt1974
...m heating bed) by damt1974
thingiverse
created to hold my 200mm borosilicate glass on my 220mm heating bed for better flattness.
thingiverse
free
Kossel mini MK2Y heated bed clamps by x2r
...d to the kossel mini.
requires an m4x12mm bolt per clamp. print 6 of them for good stability.
use abs for better heat resistance.
thingiverse
free
Glass Bed Clip by varind
...
signstek 3d printer mk2 mk3 heated bed tempered borosilicate glass plate 213x200x3mmhttps://www.amazon.com/gp/product/b00qq5q3bi
thingiverse
free
Anet A8 glass+heatbed clip by GErt09Nel
...anet a8 glass+heatbed clip by gert09nel
thingiverse
clip to secure glass bed to heat bed
glass is 4mm thick
thingiverse
free
Heated Bed Clips by productblender
...heated bed clips by productblender
thingiverse
heated bed clip for heated bed with glass and insulated with cork.
Mk2Y
thingiverse
free
Kossel mini MK2Y heated bed clamps by x2r
...d to the kossel mini.
requires an m4x12mm bolt per clamp. print 6 of them for good stability.
use abs for better heat resistance.
thingiverse
free
Adjustable supports for heated bed MK2Y 200 and FLSUN by 5imR
...mple piece you can adjust precisely and quickly the level of your printable surface. you still need 3 m3x20 screws and 3 springs.
thingiverse
free
Quick release bed clip for kossel delta by uhruh
...simply remove the glass plate by turning the clip. mk2y heat bed (220mm) glass plate (200mm x 5mm) m3...
thingiverse
free
SSR Switcher for Dual Power Supply by TK_DESIGN
...if it is not made accurate. この説明文の内容が分からない場合は見よう見まねで作らないでください。 これは危険な内容を含みます。 for mk2y round pcb heated bed.(resistance value is 2ohm) 中華の円形ヒーテッドベッド用に開発しました。 24v...
Simonwlchan
thingiverse
free
Pump stopper by Simonwlchan
... clip to prevent accidental discharge of a press-pump. sketchup source file included, mod it and save yourself from a mess today.
thingiverse
free
Remix Simonwlchan PTFE Mount by Nobel0
...ve ptfe tube and just want to pass the filament through. the filament hole is 2mm.
i uploaded the fusion 360 file.
happy printing
thingiverse
free
Belt Loop by Simonwlchan
...o versions for 10mm and 15mm spacing. all external edges rounded. prints without support or rafts, ready to go off the print bed.
thingiverse
free
Table Edge Clip by Simonwlchan
...le edge clip by simonwlchan
thingiverse
table edge-mounted clip (with small bits double sided tape) to hold a pair of gloves etc
thingiverse
free
Printrbot Cable Clips by Simonwlchan
...iverse
keep your power, usb and other cables close to the printrbot chassis. works on all sides of the metal 1403's chassis.
thingiverse
free
LCD Panel Corner Protector by Simonwlchan
... protector by simonwlchan
thingiverse
simple snap-on corner protector for the kossel lcd panel. standard piece fits all corners.
thingiverse
free
Envelope Bin Holder by Simonwlchan
...rwise discarded) mailing envelopes as desktop/ countertop bins. go green!
see how it works >> http://youtu.be/zqharqw9ep0
thingiverse
free
GrilleDuct for Printrbot by Simonwlchan
...ps against ambient temperature of 31c.
the grille is to stop my fingers getting ground every time i reach behind the printer :)
thingiverse
free
Fender Pickup Cover by Simonwlchan
...nd a gaping hole).
print this flat, and cut off the 8 corner struts, which are meant to keep the piece from warping during print.
thingiverse
free
Lenovo x240 Camera Shroud by Simonwlchan
...0 laptop that prints, mounts and works in one piece. picture shows v1 that was a tad tight, v2 (stl attached) has corrected that.
220Mm
3ddd
$1
Трубчатый нарцисс
...трубчатый нарцисс 3ddd цветы растение: трубчатый нарцисс размеры: w-220mm, d-220mm ...
3ddd
$1
TableLamp EGLO OSSAGO
...94461: - размеры: height 505mm, diameter 300mm, base diameter 220mm - е27, 1х60w настольная лампа eglo ossago арт. 94459:...
3ddd
$1
Полотенца
...полотенца 3ddd полотенце габаритные размеры: x-190mm, y-300mm, z-220mm размер полотенец: 700mm.x1400mm....
3ddd
free
Wings Lav mixer
...смеситель производитель: hamat (http://www.hamat.co.il)модель: wings lav mixerразмеры: w-210mm, d-130mm, h-220mm ...
3ddd
free
Полотенца
...полотенца 3ddd полотенце polys: 53462 габаритные размеры: x-383mm, y-384mm, z-220mm размер полотенец: 700mm.x1400mm. 500mm.x900mm. 340mm.x780mm. цвет меняется картой tow_color,...
3ddd
$1
Полотенца m20
...polys: 154144 polygonal quads only габаритные размеры: x-190mm, y-300mm, z-220mm размер полотенец: 700mm.x1400mm. 340mm.x340mm. цвет меняется картой tow_color. дополнительное...
3ddd
free
Полотенца m21
...fbx + polys: 93226 polygonal quads only габаритные размеры: x-220mm y-375mm, z-130mm. размер полотенец: 700mm.x1400mm. 500mm.x900mm. 340mm.x340mm. цвет меняется...
3ddd
$1
TZ-150
...размеры одного светильника: w-100mm, d-155mm, h-185mm размеры комплекта: w-795mm, d-220mm ...
3ddd
$1
Римские шторы
...римские производитель: - модель: римская штора размеры: w-600mm, d-38/68mm, h-1980/220mm анимированная модель римской шторы. для того чтобы модель не...
3d_export
$9
wood coffee table
...in corona render<br>polygons: 17517<br>vertices: 17486<br>measure: x=1390mm i y=1390mm i z=220mm ...
Kossel
thingiverse
free
kossel bottom by keisukelin
...kossel bottom by keisukelin
thingiverse
kossel bottom
thingiverse
free
Leg for kossel by exelon
...leg for kossel by exelon
thingiverse
leg for kossel
thingiverse
free
Extruder for kossel by spencer_chen7
...extruder for kossel by spencer_chen7
thingiverse
extruder for kossel
thingiverse
free
Kossel parts by breezer83
...kossel parts by breezer83
thingiverse
kossel parts
thingiverse
free
Anycubic Kossel PID calibration
...ir mount:
kossel raspberry camera ir mount
extruder pid calibration.
simple extruder temperature calibration of your 3d printer.
thingiverse
free
Kossel Medium by flux83
...kossel medium by flux83
thingiverse
vertex for upgraded kossel mini
thingiverse
free
Kossel Mini by salesmendesandre
...kossel mini by salesmendesandre
thingiverse
custom kossel mini
frame 20x20
thingiverse
free
leg for kossel by ionulet
...leg for kossel by ionulet
thingiverse
leg for kossel with channel for end- stop cables
thingiverse
free
Optical Endstops Mounts for Kossel (with Better Kossel carriages) by dellfer
...stops on the anycubic kossel with better kossel carriages by codefreak https://www.thingiverse.com/thing:2501337
more precission
thingiverse
free
kossel??????? by wangrui19890704
...kossel??????? by wangrui19890704
thingiverse
??2020?2060???
Heat
3d_export
$5
heat
...heat
3dexport
heat tool
3ddd
$1
electric heating
...electric heating
3ddd
обогреватель
electric heating
3d_export
$6
The heating module
...any questions also you can email to me. designed with solidworks 2017, render with keyshot **************************************
turbosquid
$2
Heating Radiator
...
royalty free 3d model heating radiator for download as blend on turbosquid: 3d models for games, architecture, videos. (1561908)
3d_export
$35
heating instalation with heat pump and solar system
...el , please contact me. before buying a model, you can try to download one of my free models and testing. thank you for watching.
turbosquid
$29
Heating Mantle
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$25
Heating Radiator
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
AT_airship_control_stand_(heated)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
AT_airship_(heated)
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Heating radiator
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Clips
archibase_planet
free
Clip
...clip
archibase planet
paper-clip clip office equipment
clip band - 3d model for interior 3d visualization.
3d_export
$5
screw clip
...screw clip
3dexport
screw clip
3d_ocean
$4
Butterfly clip
... a butterfly clip, it comes with a ready to render set for out of the box rendering. obj version and max alones version included.
turbosquid
$2
clip
...
royalty free 3d model clip for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1358622)
turbosquid
$5
Clip
...lty free 3d model clip for download as c4d, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1521355)
turbosquid
$19
Clip
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$4
Clips
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$3
clip
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$2
clips
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Clip
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
Bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
free
bed
...bed
3ddd
bed , постельное белье
bed
3ddd
$1
Bed
...bed
3ddd
bed , постельное белье , постель
bed
3d_export
$7
bed adairs bed
...rs bed
3dexport
bed adairs bed in modern style. if you want a smoother surface, please turn on turbosmooth in the modifier list.