Thingiverse
Johnybee210 FPV Quadcopter by janmittner
by Thingiverse
Last crawled date: 3 years ago
Johnybee210 is a mini 210 size FPV racing quad which is easy to print & build and very funny to fly due to its size and agileness. It is designed to be one of the smallest and lightest frames that accommodate 5" propellers and standard size flight controller (naze32/cc3d) and full size fpv camera (32x32 mm). Required printing area is 16x19 cm so it should fit vast majority of printers.
Here is a sample video from one of my flights to show that it really flies even with Xiaomi Yi HD camera: https://www.youtube.com/watch?v=0SpUMMBiInU.
When printed in ABS with 100% infill it's also quite rigid and will survive some crashes.
Total frame weight is about 75 grams (ABS, 100% infill, M3 self-tapping screws), AUW with FPV gear and 3s lipo 1000 mAh is about 350 grams.
My recommended setup:
motors: 4x 1806 2300kv (or 2204 2300kv)
ESCs: 4x DYS SN16A (or similar size and amps)
flight controller: CC3D (or Naze32)
propeller: 5045 bullnose (or 5045, 5030 etc.)
battery: 3S LiPo 1000-1600 mAh
FPV camera: PZ0420/CC1333 (or DAL700)
video TX: TS5823 200mW
This 3S setup has power to weight ratio of about 5:1 and can be compared to my other heavier copters that fly with 4S.
There are two different base plate files for 18xx or 22xx motors.
Software:
BLHeli14.1 firmware for ESCs + Damped Light mode + Oneshot125
Cleanflight 1.10 Luxfloat controller PIDs:
roll/pitch: 2, 0.040, 30
yaw: 6, 0.040, 5
looptime: 1600
With this setup you can have a greatly flying mini quadcopter for about 110 USD including FPV gear (aliexpress, banggood).
There is also a smaller version for 4" propellers (http://www.thingiverse.com/thing:1003801) and 3" propellers (http://www.thingiverse.com/thing:1091279).
Have fun!
Here is a sample video from one of my flights to show that it really flies even with Xiaomi Yi HD camera: https://www.youtube.com/watch?v=0SpUMMBiInU.
When printed in ABS with 100% infill it's also quite rigid and will survive some crashes.
Total frame weight is about 75 grams (ABS, 100% infill, M3 self-tapping screws), AUW with FPV gear and 3s lipo 1000 mAh is about 350 grams.
My recommended setup:
motors: 4x 1806 2300kv (or 2204 2300kv)
ESCs: 4x DYS SN16A (or similar size and amps)
flight controller: CC3D (or Naze32)
propeller: 5045 bullnose (or 5045, 5030 etc.)
battery: 3S LiPo 1000-1600 mAh
FPV camera: PZ0420/CC1333 (or DAL700)
video TX: TS5823 200mW
This 3S setup has power to weight ratio of about 5:1 and can be compared to my other heavier copters that fly with 4S.
There are two different base plate files for 18xx or 22xx motors.
Software:
BLHeli14.1 firmware for ESCs + Damped Light mode + Oneshot125
Cleanflight 1.10 Luxfloat controller PIDs:
roll/pitch: 2, 0.040, 30
yaw: 6, 0.040, 5
looptime: 1600
With this setup you can have a greatly flying mini quadcopter for about 110 USD including FPV gear (aliexpress, banggood).
There is also a smaller version for 4" propellers (http://www.thingiverse.com/thing:1003801) and 3" propellers (http://www.thingiverse.com/thing:1091279).
Have fun!
Similar models
thingiverse
free
Johnybee180 FPV Quadcopter by janmittner
...2280kv (or 1306 3100kv) escs: 4x dys sn16a (or similar size and amps) flight controller: cc3d atom (or naze32)...
thingiverse
free
Double Decker 175 mini FPV quadcopter by janmittner
...flight controller: cc3d atom propeller: dal 4045 bn (or similar battery: 3s-4s lipo 850-1300 mah fpv camera: sony pz0420...
thingiverse
free
Mini spider 250 quadcopter v3 by vpoten
... setup, 12a (or 18a) esc (ultra fast flight):
2207-2100kv or 2208-2000kv motors, 5x45 propellers, 4s 1600 35c battery.
enjoy!
thingiverse
free
Camera mount for QAV 210mm Quadcopter by Jetpilot212
...lipo battery
gf-osc had ccd 600tvl 5-15v camera
5,8 ghz immersionrc 25mw a/v transmitter
video link: https://youtu.be/gtdhcps62sw
thingiverse
free
Double Decker V3 200 FPV racer for 2204 motors by janmittner
...flight controller: cc3d atom propeller: dal 4045 bn (or similar e.g. triblade) battery: 3s-4s lipo 850-1300 mah fpv camera:...
thingiverse
free
Froggy 150 micro FPV racer by janmittner
...4x 1306 3100kv (http://www.banggood.com/dys-1306-3100kv-bx-series-brushless-motor-for-multicopter-cw-ccw-p-962149.html) escs: 4x dys sn16a (or similar size and amps) (http://www.banggood.com/ztw-spider-series-18a-opto-esc-with-simonk-oneshot-program-p-983660.html) flight controller: cc3d atom (http://www.banggood.com/openpilot-cc3d-atom-mini-cc3d-fpv-flight-controller-cc3d-evo-p-970762.html)...
thingiverse
free
Red Dwarf 135/155 micro FPV Quadcopter by janmittner
...4x 1306 3100kv (http://www.banggood.com/dys-1306-3100kv-bx-series-brushless-motor-for-multicopter-cw-ccw-p-962149.html) escs: 4x dys sn16a (or similar size and amps) (http://www.banggood.com/ztw-spider-series-18a-opto-esc-with-simonk-oneshot-program-p-983660.html) flight controller: cc3d atom (http://www.banggood.com/openpilot-cc3d-atom-mini-cc3d-fpv-flight-controller-cc3d-evo-p-970762.html)...
thingiverse
free
Double Decker V2 200 FPV racer by janmittner
...flight controller: cc3d atom propeller: dal 4045 bn (or similar battery: 3s-4s lipo 850-1300 mah fpv camera: sony pz0420...
thingiverse
free
Mini H FPV quadcopter by vpoten
...3 2000kv, tiger mn-1806 2300kv or rctimer hp1806 2300kv. use 5030 propellers.
mobius hd camera (lightweight).
simonk 12a esc.
thingiverse
free
Mini spider quadcopter PD2015 by vpoten
... setup, 12a (or 18a) esc (ultra fast flight):
2207-2100kv or 2208-2000kv motors, 5x45 propellers, 4s 1600 35c battery.
enjoy!
Janmittner
thingiverse
free
QAV210 motor protector by janmittner
...qav210 motor protector by janmittner
thingiverse
i designed this light protector to save my cobra motors on qav 210.
thingiverse
free
QAV210 motor protector (rounded) by janmittner
...qav210 motor protector (rounded) by janmittner
thingiverse
i designed this light protector to save my cobra motors on qav 210.
thingiverse
free
BDX Racer FPV mini quad motor protector by janmittner
...bdx racer fpv mini quad motor protector by janmittner
thingiverse
simple motor guard for red20rc bdx racer
thingiverse
free
Johnybee180 FPV Quadcopter by janmittner. "SKY Version" by skydge
...actualización placa superior.
con xt60 macho y soporte para antena a 45º
special thanks to janmittner by those very good designs.
thingiverse
free
ZMR250 motor protector 2204 2206 2208 by janmittner
...50 has quite narrow arms, any 220x motor is not very well protected. so i created this motor protection to have the motors safer.
thingiverse
free
ZMR250 Low Rider modification by janmittner
...hardware:
2x 35mm spacer
6x 20mm spacer
2x 13mm spacer
of course you can change the height of spacers to adjust it to your needs.
thingiverse
free
SJ4000 - 20 degree tilted mount for FPV quadcopter by janmittner
... any fpv quad. simply attach the mount to the frame with double-sided tape, put the camera on it and wrap with some velcro strap.
thingiverse
free
Xiaomi Yi - 20 degree tilted mount for FPV quadcopter by janmittner
... any fpv quad. simply attach the mount to the frame with double-sided tape, put the camera on it and wrap with some velcro strap.
thingiverse
free
Rotorama Mefisto / Morfeus HD camera mount by janmittner
...er of the frame.
no supports or rafts needed, very easy to print. recommended to print with tpu but also abs or pla should work.
thingiverse
free
Johnybee180 FPV Quadcopter by janmittner
...ttp://www.thingiverse.com/thing:1069161) and smaller for 3" propellers (http://www.thingiverse.com/thing:1091279).
have fun!
Quadcopter
3d_export
$5
quadcopter
...quadcopter
3dexport
futuristic quadcopter design.<br>original design davidflo 77
turbosquid
$19
quadcopter
...lty free 3d model quadcopter for download as max, ma, and obj on turbosquid: 3d models for games, architecture, videos. (1591426)
turbosquid
$25
QuadCopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
Quadcopter 3D Model
...quadcopter 3d model
3dexport
quadcopter studio shaders
quadcopter 3d model vortex333 93968 3dexport
3d_export
$5
Quadcopter 3D Model
...quadcopter 3d model
3dexport
quadcopter aircraft helicopter
quadcopter 3d model greatghost 94019 3dexport
3d_export
$18
passenger quadcopter
... a multicopter is an aircraft built according to a helicopter scheme, with three or more rotors. previews rendered with redshift.
turbosquid
$159
Quadcopter Animated.
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$19
Drone Quadcopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$12
Drone Quadcopter
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$29
Quadcopter
...
questions about the continuation of the collection or the model can be asked here:<br>https://www.artstation.com/evgen_beg
Fpv
turbosquid
$1
FPV VTX Antenna
...e 3d model fpv vtx antenna for download as obj, fbx, and stl on turbosquid: 3d models for games, architecture, videos. (1230317)
3d_export
$9
Fpv logo 3D Model
...onogram vehicle part of auto transport 3d model logo emblem detailed high quality badge
fpv logo 3d model rmodeler 59628 3dexport
3d_export
$8
dji fpv battery slot holder
...er for 3 dji fpv batteries. holds perfectly without shaking. need 1 m3 countersunk head bolt. need to print 6 pin, 1 case, 1 cap.
3d_export
$10
fpv camera hd 700tvl
...aterials are logically named<br>the main format is in 3ds max 2009.<br>satisfcation garranteed..<br>thank you !
thingiverse
free
FpV Mount (SOPORTE FPV) by elborjas1987
...fpv mount (soporte fpv) by elborjas1987
thingiverse
this is a fpv mount with the same holes of naza base.
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
fpv by tbutera
...fpv by tbutera
thingiverse
fpv
thingiverse
free
FPV DRONE ROOSTER DJI FPV PART
...fpv drone rooster dji fpv part
thingiverse
fpv drone rooster dji fpv install part
thingiverse
free
FPV monitor
...tml?rmmds=myorder&cur_warehouse=cn
link for download : https://cults3d.com/fr/mod%c3%a8le-3d/divers/fpv-monitor-ecran-fpv-faf
thingiverse
free
FPV receiver mount for FPV display by petrex
...eceiver mount for fpv display by petrex
thingiverse
aomway receiver mount for field view 777 fpv monitor. with small cable tray.