Thingiverse
iPad Teleprompter by speedy777
by Thingiverse
Last crawled date: 3 years ago
I needed a video camera teleprompter recently and (unbelievably!) did not find one already on Thingiverse (as of July 9th, 2016), so had to cobble one up quickly. I'm sharing it here for anyone who needs something like this.
This was quickly designed for my specific needs so please don't complain that it doesn't do this or that. If you need something else, please modify it or design it yourself.
Some notes:
The ipad arms and camera risers are mirrored, so just print two of each
The glass is 10" x 8" and was appropriated from a picture frame. In my case, the glass was 2.25mm thick. I placed 3M blue tape around the perimeter of the glass initially to protect from sharp edges, but ended up printing up some protective edges for the glass. I left the tape in place as it allows for a better grip, especially for the hinges.
The glass is just a press fit onto the hinge, so only install it when you are ready to use it. It can fall off if you are not careful.
The ipad holder is sized for an iPad 2 with no case but should allow everything else to sit in place, except maybe an original iPad 1
The camera risers are designed to be glued into the slots on the base. I used 2 part epoxy glue
The tripod mount is a Manfrotto quick release style specifically for my tripod. It may or may not work for you. It is screwed and glued onto the base. I may add some other mounts later on, or you can design your own. ** Update - I added a mount that accepts a tripod screw, but I did not test it. I'm not sure it's strong enough to hold the whole contraption on the tripod, so use at your own risk.
Try to balance your camera and ipad in such a way that the tripod mount is the center of gravity. 3-D PLA printed stuff is not that strong, especially with the grain, and can easily break if too much weight is applied.
Everything else is screwed together with #6-32 screws cut to length, except for the hinges, which use #10-32 wingnuts and studs. The camera tripod screw is a 1/4"-20 screw. You can probably find a 1/4-20 wingnut stud but I used what I had around, which was a screw, so you need a screwdriver to tighten.
The hinge wing nuts are not positioned in the best way for tightening with the glass in place, so I suggest you use Loctite and tighten them before inserting the glass in place.
Ideally, you should cover the glass and camera with a black cloth, but if your background is dark and you turn up the brightness on the ipad you may be able to get away without it.
** 7/11/2016 - Added Manfrotto round mount for Compact Action tripod
This was quickly designed for my specific needs so please don't complain that it doesn't do this or that. If you need something else, please modify it or design it yourself.
Some notes:
The ipad arms and camera risers are mirrored, so just print two of each
The glass is 10" x 8" and was appropriated from a picture frame. In my case, the glass was 2.25mm thick. I placed 3M blue tape around the perimeter of the glass initially to protect from sharp edges, but ended up printing up some protective edges for the glass. I left the tape in place as it allows for a better grip, especially for the hinges.
The glass is just a press fit onto the hinge, so only install it when you are ready to use it. It can fall off if you are not careful.
The ipad holder is sized for an iPad 2 with no case but should allow everything else to sit in place, except maybe an original iPad 1
The camera risers are designed to be glued into the slots on the base. I used 2 part epoxy glue
The tripod mount is a Manfrotto quick release style specifically for my tripod. It may or may not work for you. It is screwed and glued onto the base. I may add some other mounts later on, or you can design your own. ** Update - I added a mount that accepts a tripod screw, but I did not test it. I'm not sure it's strong enough to hold the whole contraption on the tripod, so use at your own risk.
Try to balance your camera and ipad in such a way that the tripod mount is the center of gravity. 3-D PLA printed stuff is not that strong, especially with the grain, and can easily break if too much weight is applied.
Everything else is screwed together with #6-32 screws cut to length, except for the hinges, which use #10-32 wingnuts and studs. The camera tripod screw is a 1/4"-20 screw. You can probably find a 1/4-20 wingnut stud but I used what I had around, which was a screw, so you need a screwdriver to tighten.
The hinge wing nuts are not positioned in the best way for tightening with the glass in place, so I suggest you use Loctite and tighten them before inserting the glass in place.
Ideally, you should cover the glass and camera with a black cloth, but if your background is dark and you turn up the brightness on the ipad you may be able to get away without it.
** 7/11/2016 - Added Manfrotto round mount for Compact Action tripod
Similar models
thingiverse
free
Tripod Teleprompter Holder by harlanlw
...mazon basic tripod and is glued to the underside of the teleprompter. it is just slid in place on the tripod between the holder.
thingiverse
free
Updated teleprompter Tripod mount by losguys
... a bit small for my tripod, so i added some width and chamfered the corners to better match my original. i have a velbon tripod.
thingiverse
free
Reflective Teleprompter Parts by nt86
...ount lenses, but it will probably work with a number of other cameras. you may need to modify the design to make it work for you.
thingiverse
free
iPad Pro Tripod Mount by rnoetzel
...nough to use it "outdoor". but they is sufficient to take photos and videos of objects that do not require camera pans.
thingiverse
free
Teleprompter for smartphone or tablet
...9;m including the actual f360 file so you can tweak dimensions as needed, that's why i initially remixed the original design.
thingiverse
free
Ipad Mini Holder with Tripod Mount hole by gustofusion
... filament for this project. i print on end with auto generated supports. i have also enclosed a pre sliced version with supports.
thingiverse
free
GoPro Manfrotto Tripod Mount by downeym
...tto 234rc tripod quite well and uses a standard m5 nut. the standard gopro thumbscrew is a little short, but seems to still work.
thingiverse
free
Shoulder Rig for DSLR by modelatolyesi
.... (shoulder stand to back mount)
-12x #2 sheet metal screws. (used to tighten back mount, front mount and handle mounts to tubes)
thingiverse
free
iPad Universal Wall Mount by iggylark
...it should work with majority of ipad models, or similar tablets. please check dimensions if not sure. i will...
thingiverse
free
Fixed C270 Tripod Hinge by ryanscheidter
...s excellent logitech c270 tripod.
the dimensions have been tightened up significantly so that the camera doesn't flop around.
Speedy777
thingiverse
free
Triangle Mold for Zongzi or Joong by speedy777
...777
thingiverse
triangular mold to make traditional zongzi or joong.
check out youtube for ways to combine and fold the leaves.
thingiverse
free
Neewer-compatible mount for Speedy777's Teleprompter by digitallyhip
...on fiber tripod (and i suspect all neewer tripod heads).
i shaved 2mm off the plate in tinkercad and printed and am very pleased.
thingiverse
free
Accessories for speedy777's iPad Teleprompter by xrr
...mm glass, resize accordingly
i use this great tripod mobile phone clamp design with it.
https://www.thingiverse.com/thing:2790283
thingiverse
free
FlashForge Creator pillow block - for MF105ZZ flanged bearing by speedy777
...anged 10x5x4 bearing that is used on the pulley already. this way, you only need to keep one type of spares for all the bearings.
thingiverse
free
Steering arm for WPL B-16 and C24 by speedy777
...he steering geometry from the single angled arm. the servo bushing is used on the screw to allow it to slide up and down the arm.
thingiverse
free
Pump Hand Drill by speedy777
...
my rendition of a hand drill received from performance 3d llc
added 3 chuck sizes
video here: http://youtu.be/ut9gkjpn2f4
thingiverse
free
Wingnut caps for platform thumbscrews on FlashForge Creator by speedy777
...thumbscrews on a long screw and then press them into the hole. the heat will soften the plastic enough for it to slide in snugly.
thingiverse
free
Hinge and Knob for front door for FF Creator by speedy777
... to the bottom of the fixed knob.
for details about the top enclosure brackets, go here:http://www.thingiverse.com/thing:731439
thingiverse
free
Fan ducts to exhaust printing fumes to the outside by speedy777
... at the window end, depending on your window type, just use a piece of plywood and cut a rectangular hole for the window adapter.
Teleprompter
3d_export
$15
teleprompter
...e up render. - all parts and materials are logically named. other formats ================= - collada (.dae) - autodesk fbx - obj
thingiverse
free
teleprompter by ivan_riazanov
...teleprompter by ivan_riazanov
thingiverse
teleprompter for 120х112х0.4 glass with angle adjustment
thingiverse
free
Teleprompter light
...teleprompter light
thingiverse
super light teleprompter for ipad or other tablets/phones with 5.9 mm thickness
thingiverse
free
Teleprompter (Experimental) by seakingsh3
...inished!
you will also need:
4x 15mm rods
14x m3 screw/nut
glas
fabric (for cover)
i will add more information and a video later.
thingiverse
free
DIY Teleprompter by andrewngai
...er that i designed. it uses 1 inch square aluminum tube and a 12 x 9 inch photo frame
https://www.youtube.com/watch?v=qzwg6rwexae
thingiverse
free
Tripod Teleprompter Holder by harlanlw
...mazon basic tripod and is glued to the underside of the teleprompter. it is just slid in place on the tripod between the holder.
thingiverse
free
Teleprompter for GoPro
...ightly since i printed mine - made it a bit wider and streamlined the backplate a touch - but i think it should still print fine.
thingiverse
free
Teleprompter by soexpired
...s an open design https://cad.onshape.com/documents/d19e80b0b90cb04665f5d6ad/w/6aa241ff2050f3e3e5133f27/e/bd5fe8fafaee773cabe7e384
thingiverse
free
Teleprompter Base Split by cladkins
...se from speedy777 ipad teleprompter. the tripod base was too large for my print bed. hopefully, this saves somebody an extra step
thingiverse
free
PTP2 Teleprompter by DualPeaks
...hing:2634357
setup video: https://www.youtube.com/watch?v=smmyc0nnlza
features video: https://www.youtube.com/watch?v=ajgcubayxcs
Ipad
3ddd
$1
iPad
... ipad , планшет
качественная модель ipad
все материалы и текстуры в архиве
3ddd
$1
IPad
... ipad , планшет
модель ipad, текстурированая, материалы vray 1.5 sp2, 3dsmax 2009
3ddd
$1
Ipad mini
...ipad mini
3ddd
apple , ipad , планшет
ipad mini
turbosquid
$63
iPad
...
royalty free 3d model ipad for download as 3ds, max, and obj on turbosquid: 3d models for games, architecture, videos. (1299607)
3d_ocean
$16
iPad 2
...ad 2 nurbs texture
compatible with cinema 4d 12.0 or higher. since ipad 2 is so new, it’s difficult to know exactly how it looks.
3d_export
$10
ipad base
...ipad base
3dexport
ipad base can be manufactured and comfortable to operate
turbosquid
$15
Ipad
...odel ipad generic for download as max, obj, fbx, lxo, and stl on turbosquid: 3d models for games, architecture, videos. (1208625)
3d_ocean
$15
3D Ipad Air
...hite. high quality model and materials. - 2 color models - polycount 6.967 - without turbosmooth - created in 3d max 2014 - pl...
3ddd
$1
Apple iPad Pro
...apple ipad pro
3ddd
apple , ipad
new apple ipad pro
3d_ocean
$15
iPad
...en noted down and has been implemented into the 3d model. the curvature of the back, which is indeed a difficult task to recre...