Thingiverse
Holders for pegboard by pbannister
by Thingiverse
Last crawled date: 3 years ago
Holders for mounting on pegboard. Also an exercise to bring up my CAD/FDM printing vocabulary. As the first picture hints, going through a series of iterations to work out what works (or not).
So far...
Holder for Screwdrivers - posted separately: https://www.thingiverse.com/thing:2405739
Arms - 4in and 6in arms (used for hand saws and clamps), and 6in "strong" arms.
Holder for wood rasp.
Holder for metal snips.
See also:https://www.thingiverse.com/thing:2405739
Major goals (as the above):
Use with common (in the USA) pegboard with 1/4" holes on 1" spacing.
Can use common drywall screws (or any "wood" screw with ~4mm outside diameter).
Does not damage the pegboard.
Anchors should be somewhat re-usable.
Very solid mount with screw/anchor together.
Minor goals:
Printable without supports (where practical).
Uses minimal plastic for the needed strength.
Strong as possible with the material used. (Slightly redundant with the prior.)
Note in particular the bit you do not see - the bits of plastic that act as anchors. I wanted something much stronger than a plastic peg. The majority of the load is taken by the metal screw. The bit of plastic that acts as anchor compresses against the pegboard hole and the back of the pegboard, just enough to hold the screw in place. The result is solid and strong.
If you end up moving around things a lot before settling on final arrangement, you might wear out some anchors, and have to print a few replacements. As the anchors take relatively little time to print (15-20 minutes in my case), this is acceptable.
Note that at present this design for arms is entirely suitable for lighter objects, but not as good as I would like for heavier objects. The problem is that FDM prints are stronger with than across the "grain" of the print. In the current print (when printed with the arm horizontal), the arm is reasonably strong, but the base above the arm is a bit weak.
If you print the arms in the same orientation as when on the pegboard, you do not need support structure. If you print the arms sideways, you must use support structures, but the base of the arm is stronger (due to the "grain" of the plastic).
So far...
Holder for Screwdrivers - posted separately: https://www.thingiverse.com/thing:2405739
Arms - 4in and 6in arms (used for hand saws and clamps), and 6in "strong" arms.
Holder for wood rasp.
Holder for metal snips.
See also:https://www.thingiverse.com/thing:2405739
Major goals (as the above):
Use with common (in the USA) pegboard with 1/4" holes on 1" spacing.
Can use common drywall screws (or any "wood" screw with ~4mm outside diameter).
Does not damage the pegboard.
Anchors should be somewhat re-usable.
Very solid mount with screw/anchor together.
Minor goals:
Printable without supports (where practical).
Uses minimal plastic for the needed strength.
Strong as possible with the material used. (Slightly redundant with the prior.)
Note in particular the bit you do not see - the bits of plastic that act as anchors. I wanted something much stronger than a plastic peg. The majority of the load is taken by the metal screw. The bit of plastic that acts as anchor compresses against the pegboard hole and the back of the pegboard, just enough to hold the screw in place. The result is solid and strong.
If you end up moving around things a lot before settling on final arrangement, you might wear out some anchors, and have to print a few replacements. As the anchors take relatively little time to print (15-20 minutes in my case), this is acceptable.
Note that at present this design for arms is entirely suitable for lighter objects, but not as good as I would like for heavier objects. The problem is that FDM prints are stronger with than across the "grain" of the print. In the current print (when printed with the arm horizontal), the arm is reasonably strong, but the base above the arm is a bit weak.
If you print the arms in the same orientation as when on the pegboard, you do not need support structure. If you print the arms sideways, you must use support structures, but the base of the arm is stronger (due to the "grain" of the plastic).
Similar models
thingiverse
free
Screwdriver holder for pegboard by pbannister
...ry easy to over-torque with a power tool.)
the trickiest part of this design was the anchors, and i am satisfied with the result.
thingiverse
free
Stepper Drillbit Pegboard Holder by Badadz
...: uploaded a copy without the labels: stepper drillbit pegboard holder(no-labels).stl (you could use dymo labels etc if you like)
thingiverse
free
Pegboard Spacer by hrabbot
...tip using thingiverse's "tip designer" button. i've enjoyed the ability to tip designers for the same reasons.
thingiverse
free
Large Angled Pegboard Tape Holder by Badadz
...g:4828343
stepper drillbit pegboard holder: https://www.thingiverse.com/thing:4826896
i have been on a pegboard mission recently.
thingiverse
free
Bit Holder Pegboard Bracket
...tacts the print bed and turn on basic supports and all you will need to do is remove some small supports under the mounting pegs.
thingiverse
free
Pegboard Dremel Bit Holder by FusionBolt
...also print two of the file "pegboard-v-rack_support_30.stl" found here: https://www.thingiverse.com/thing:2108670/files
thingiverse
free
Warped Arches by UptonAK
...by uptonak
thingiverse
holder of things. no supports needed. lightweight and strong structure.
please post photos if you print!
cg_trader
$6
Bottle holder for pram Anex Sport | 3D
...to the stroller, it is necessary to screw a screw about 6–9 mm long with a large cap into the bottle holder (shown in the photo).
thingiverse
free
Screwdriver Pegboard Holders (4 sizes) by Badadz
...stronger regular support i am making some containers of similar size and style too - shoulod be posted in...
thingiverse
free
Dremel 400 Küpper Holder by therealmrgadget
...head screws at the rear to provide anchors to küpper board. this way the entire print can be made without using support material.
Pbannister
thingiverse
free
Desktop tools organizer by pbannister
...desktop tools organizer by pbannister
thingiverse
simple holder for tools (files, mostly in my use) kept near my 3d printer.
thingiverse
free
Oumuamua by pbannister
...have as evidence is a single wavering colored pixel.
discussion: https://plus.google.com/u/0/+prestonbannister/posts/l1zty5pxcg4
thingiverse
free
Spooler holder by pbannister
...he common size for skateboards. should fit most any size spool.
could print the inner and outer bits separately, or as one print.
thingiverse
free
Hinge (meant for printer enclosure) by pbannister
... number of iterations to get a hinge (for a printer enclosure) that prints well.
will update this once the enclosure is finished.
thingiverse
free
Clips for TV tray by pbannister
...ined.
the caveat is that i do not (yet) know if they work! shipped the printed parts off to a relative, who needed replacements.
thingiverse
free
Pegboard upgrade for TronXY X5S by pbannister
...xibility, with better appearance, while at least seeming more organized. (added a raspberry pi running octopi ... so more wires.)
thingiverse
free
Spooler holder (by pbannister) Remix by cntryder
...nter bearing spacer i printed with 10% infill.
a couple of the parts may require supports in a few areas. just use you judgement.
thingiverse
free
Steve from Minecraft by pbannister
...ructure, and you should have a working toy. (suggest you print face-up. painting the face and/or body is up to you.)
have fun. :)
thingiverse
free
Archimedes screw by pbannister
...ernatively, you could remove the crank and turn the screw with an 8mm allen key - perhaps attached to an electric motor or drill.
thingiverse
free
Rockets!! by pbannister
...iralized" (or "vase mode") prints. also, if you push speed, they seem good for finding the faults in your printer.
Pegboard
turbosquid
free
puzzle pegboard with square and triangle puzzle
... pegboard with square and triangle puzzle for download as max on turbosquid: 3d models for games, architecture, videos. (1634635)
3d_export
$6
Workshop Tools 02 - PBR -
...vise<br>63 base pieces<br>73 prefabs<br>30 textures in 2k<br>10 materials<br>polygon count:<br>30,071<br>workbench: 848<br>pegboard 6<br>toolholder 01: 46<br>toolholder 02: 503<br>toolholder 03: 366<br>toolholder 04: 114<br>trisquare:...
thingiverse
free
Pegboard Box
...pegboard box
thingiverse
this is a box for pegboard
thingiverse
free
Pegboard hook
...pegboard hook
thingiverse
pegboard hook
thingiverse
free
pegboard hook
...pegboard hook
thingiverse
pegboard hook
thingiverse
free
Pegboard hook
...pegboard hook
thingiverse
another pegboard hook.
thingiverse
free
Pegboard Box
...pegboard box
thingiverse
pegboard box that uses standard 1" l pegboard hooks spaced at 2.925" (74.30mm) apart.
thingiverse
free
Pegboard by baberone
...rone
thingiverse
remix of pegstr - pegboard wizard project by mgx to fit my needs.
my pegboard is getting nicely organised now !
thingiverse
free
Customizable pegboard
...customizable pegboard
thingiverse
customizable pegboard for laser cutting. specify desired size and offsets.
thingiverse
free
printable pegboard
...printable pegboard
thingiverse
smaller printable pegboard, can fit into creality ender 3
Holders
archibase_planet
free
Holder
...holder
archibase planet
holder toilet paper holder
holder paper n070712 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...e planet
holder rack toilet paper holder
holder toilet roll n240715 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
pen holder support prop
pen holder - 3d model for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
pole post holder
сhurch cross pole holder - 3d model for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder bathroom ware
shower holder - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...oilet paper holder
holder paper devon&devon; time black n241113 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder hanger hanger for towel
holder 7 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder hanger hanger for towel
holder 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder towel rack towel-horse
holder - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...lder
archibase planet
holder hanger hanger for towel
holder towel n250912 - 3d model (*.gsm+*.3ds) for interior 3d visualization.