Thingiverse
HICTOP Marlin RC7 firmware by DRNoble
by Thingiverse
Last crawled date: 3 years ago
Introduction
This is the marlin firmware (https://github.com/MarlinFirmware/Marlin) for the HICTOP Prusa i3, set up on a default machine based on the metal framed linear rail model with no alterations accept metal version of extruder on bowden feed with E3d v6 which should not affect usability on the original as its the same motor and gear, using the standard 2mm pitch Z axis lead screws. while i was trying to set this up looking about i notice some of the firmware already out there had the Z axis set to 2560 steps per mm, this is wrong for the stock configuration i have, so this has a corrected Z axis steps in configuration.h, this also corrects a problem with the default firmware when using the extra drilled PCB the tip is brought back to home with the Z axis at 0 so it always hit the foldback clips.
Warning
although i have tested this firmware thoroughly on my HICTOP Prusa i3 i cannot provide any warranty as far as installing it on your printer, continue at your own risk. i cannot be held responsible for you bricking your printer.
Installation
To upload this to your printer you can open the marlin.ino with the arduino IDE, there are already a substantial amount of explanations out there on how to do this but i will try to explain this best i can, this particular version of the marlin firmware is set up for the MKS/Arduino + RAMPS based board (RED). the intallation steps are as follows....
Download and extract Marlin firmware attached to this post
Open Arduino then open marlin.ino by navigating to the folder where you extracted the firmware in File > Open...
Set correct com port and board in Tools > Port & Tools > Board, the board wants to be set to arduino mega.
Click verify to make sure there are no errors, if it compiles successfully go ahead and click upload.
Enjoy rc7 Marlin Firmware on your stock HICTOP
Extruder (optional)
i changed my own printer to a E3D J-head v6, this also includes all the stl files for the blower and the carriage mount, i borrowed the mount from MMendel and redesigned the blower to give more print cooling and hold an induction sensor. Also if you change the hotend you will need to run PID tuning otherwise the hotend wont get to temperature. and the induction sensor is not set up with this firmware, i do plan on upgrading this firmware to rc8 and adding the sensor and possibly redesigning the blower should there be any problems with induction sensor adjustment, with it all fitted there is only about 1mm clearance with the nozzle tip. this may cause a problem with z-axis calibration on the induction sensor.
After thoughts
I set the firmware to have my own text on the lcd if you want to replace this text with your own then open configuration.h in arduino and then press Ctrl + F and type CUSTOM_MACHINE_NAME into the text field that appears. That should take you to the line to rename the machine.
This is the marlin firmware (https://github.com/MarlinFirmware/Marlin) for the HICTOP Prusa i3, set up on a default machine based on the metal framed linear rail model with no alterations accept metal version of extruder on bowden feed with E3d v6 which should not affect usability on the original as its the same motor and gear, using the standard 2mm pitch Z axis lead screws. while i was trying to set this up looking about i notice some of the firmware already out there had the Z axis set to 2560 steps per mm, this is wrong for the stock configuration i have, so this has a corrected Z axis steps in configuration.h, this also corrects a problem with the default firmware when using the extra drilled PCB the tip is brought back to home with the Z axis at 0 so it always hit the foldback clips.
Warning
although i have tested this firmware thoroughly on my HICTOP Prusa i3 i cannot provide any warranty as far as installing it on your printer, continue at your own risk. i cannot be held responsible for you bricking your printer.
Installation
To upload this to your printer you can open the marlin.ino with the arduino IDE, there are already a substantial amount of explanations out there on how to do this but i will try to explain this best i can, this particular version of the marlin firmware is set up for the MKS/Arduino + RAMPS based board (RED). the intallation steps are as follows....
Download and extract Marlin firmware attached to this post
Open Arduino then open marlin.ino by navigating to the folder where you extracted the firmware in File > Open...
Set correct com port and board in Tools > Port & Tools > Board, the board wants to be set to arduino mega.
Click verify to make sure there are no errors, if it compiles successfully go ahead and click upload.
Enjoy rc7 Marlin Firmware on your stock HICTOP
Extruder (optional)
i changed my own printer to a E3D J-head v6, this also includes all the stl files for the blower and the carriage mount, i borrowed the mount from MMendel and redesigned the blower to give more print cooling and hold an induction sensor. Also if you change the hotend you will need to run PID tuning otherwise the hotend wont get to temperature. and the induction sensor is not set up with this firmware, i do plan on upgrading this firmware to rc8 and adding the sensor and possibly redesigning the blower should there be any problems with induction sensor adjustment, with it all fitted there is only about 1mm clearance with the nozzle tip. this may cause a problem with z-axis calibration on the induction sensor.
After thoughts
I set the firmware to have my own text on the lcd if you want to replace this text with your own then open configuration.h in arduino and then press Ctrl + F and type CUSTOM_MACHINE_NAME into the text field that appears. That should take you to the line to rename the machine.
Similar models
thingiverse
free
Hictop 3DP17 Marlin latest firmware configuration by vlachoudis
...top functionality is supported (including filament detector) and additionally i've enabled the saving to eeprom, babystepping
thingiverse
free
Custom MakerGear_Bootscreen.h file by SCHMENKE
... the marlin firmware (line 105 in 1.1.0 rc7), it is enabled by un-commenting the line;
"#define show_custom_bootscreen"
thingiverse
free
Marlin Firmware for HICTOP 3DP08 Printer by MATIASVIANO
...viano
thingiverse
this is the lastest rc6 firmware, adapted to hictop 3d printer 3dp08, just download de arduino ide and upload!
thingiverse
free
CTC I3 Pro B firmware by YoYo_Crescendo
... thermal_runaway_protection_bed_period 20 //in seconds
//#define thermal_runaway_protection_bed_hysteresis 2 // in degree celsius
thingiverse
free
Z mechanical stop for BQ Hephestos 2 by 3Dadicto
...ected in the same place. be careful with the positive and the negative, that they are well connected
https://youtu.be/y3elbnzy-rm
thingiverse
free
Inductive sensor mount BQ Prusa i3 by ajpl
... out my new design which enables you to have led lights on top of the inductive sensor! https://www.thingiverse.com/thing:2348123
thingiverse
free
MK8 extruder mount for I3-RS 3d printer by adiasmesquita
...t;#define fix_mounted_probe
comment this line in configuration.h
=>//#define bltouch
adjust x,y,z offsets
adjust probes points
thingiverse
free
Prusa I3 Anycubic Inductive Sensor Mount by msrd0
... inductive sensor behind your print head.
you can find a version of the marlin firmware with auto bed leveling enabled on gitlab.
thingiverse
free
Inductive proximity sensor bracket by takuya
...lj12a3-4-z-by-inductive-proximity-sensor-detection-switch-pnp-dc6-36v-/140907575134?pt=lh_defaultdomain_0&hash=item20cebef75e
thingiverse
free
Marlin 1.1.0-RC7 for Sunhokey Prusa i3 2015 by farrukh
...ino software is recommended for flashing. there are plenty of resources available on internet about how to flash marlin firmware.
Rc7
thingiverse
free
Flyingbear-P902 firmware RC7 by Tomasolsson
...20161202:
enable: #define fast_pwm_fan
enable: #define pidtempbed
enable: #define eeprom_settings
enable: #define eeprom_chitchat
thingiverse
free
Marlin 1.1.0-RC7 for Sunhokey Prusa i3 2015 by farrukh
...ino software is recommended for flashing. there are plenty of resources available on internet about how to flash marlin firmware.
thingiverse
free
Flyingbear p902 Fanduct (Inductive Proximity Sensor) by Tomasolsson
...by tomasolsson thingiverse this will not work with marlin rc7 http://www.thingiverse.com/thing:1859628 fanduct for flyingbear p902 with inductive proximity sensor...
thingiverse
free
Custom MakerGear_Bootscreen.h file by SCHMENKE
...file of the marlin firmware (line 105 in 1.1.0 rc7, it is enabled by un-commenting the line; "#define...
thingiverse
free
Auto Bed Leveling tutorial (Prusa i3) by PanzerOwl
...for prusa i3. you can download my marlin in"myprusai3自動校正.zip"(marlin rc7 also see youtube:...
thingiverse
free
Reach3D - E3D V6, BLTouch, Titan Mount by QuantumBIggs
...this working with marlin 1.1.0-rc7. updated 2/27/2017: attached marlin 1.1.0-rc7 configuration.h. there was a bug in this version that...
thingiverse
free
Auto bed leveling Prusa i3 rework without Metal Bed by giecuk
...it without problems... i upload the firmware of marlin rc7 that already setting up the auto bed...
thingiverse
free
Hardware and Software Mods M150 by Pedro51
...puissance plateau (bed) mettre à jour marlin en version rc7 (1.1.7) auto nivellement expliqué modifier le bootscreen (écran de...
thingiverse
free
Tevo Tarantula Direct E3D Titan X-Carriage with BLTouch by grzszcze
...hardware. the following changes were done using marlin 1.1 rc7 & mks base 1.2: uncomment define use_xmax_plug changed x_home_dir...
Hictop
thingiverse
free
Hictop - Adjustable z Endstop by ptk21
...hictop - adjustable z endstop by ptk21
thingiverse
adjustable z endstop for hictop
thingiverse
free
Hictop 3d LCD Befestigung by festus402
...hictop 3d lcd befestigung by festus402
thingiverse
hictop 3d lcd befestigung
thingiverse
free
Cable chain HICTOP by Insani3D
...cable chain hictop by insani3d
thingiverse
iniciando la modificación de nuestra hictop, se diseña una eslabón a medida.
thingiverse
free
hictop y belt mount by polpetras
...hictop y belt mount by polpetras
thingiverse
hictop aluminum prusa y belt mount
thingiverse
free
Pen Holder for Hictop ender by basolur
...pen holder for hictop ender by basolur
thingiverse
this is a simple pen holder to use a hictop ender as a plotter.
thingiverse
free
remix for hictop mount by chibi_hero
...iverse
edit. made recesses for mounting deeper.
remixed this with http://www.thingiverse.com/thing:1323225
for my hictop 3dp-11.
thingiverse
free
Hictop 3DP-17 Parts by Adranovik
...hictop 3dp-17 parts by adranovik
thingiverse
printed parts for the hictop prusa eds-17 with auto level
thingiverse
free
Hictop xaxis clamp by Gen0idea
...oken x-axis belt clamp on the hictop printer.
printed in a different colour to the original to differentiate it as a replacement.
thingiverse
free
Hictop xaxis clamp by Gen0idea
...oken x-axis belt clamp on the hictop printer.
printed in a different colour to the original to differentiate it as a replacement.
thingiverse
free
Hictop i3 RAMPS Board Cover
...hictop i3 ramps board cover
thingiverse
cover for the stock ramps 1.3 board on the hictop i3 clone (2015 model).
Marlin
3d_export
$35
Marlin
...s : zbrush 3ds max ztool obj fbx dae 3ds stl properties : 8*14*6 production time : 15 hours 52 gram models are drawn with zbrush.
3ddd
$1
Faro Marlin pendant
...mpara colgante blancohttp://www.faro.es/es/productos/marlin-lampara-colgante-blanco/
polyrate: 14107
в архиве fbx+obj
3ddd
$1
Faro Marlin bra
...
marlin black wall lamphttp://www.faro.es/en/productos/marlin-lampara-aplique-negro/
polyrate: 15491
в архиве fbx+obj
turbosquid
$19
Blue marlin
...e 3d model blue marlin for download as max, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1341037)
3d_export
$60
Marlin Blue 3D Model
...marlin blue 3d model
3dexport
fish sea 3ds marlin mental ray textured animals
marlin blue 3d model ojoalperro 57644 3dexport
3ddd
free
Brass Marlin
... винтаж , марлин
статуэтка марлина из латуни. винтаж.
3d_export
$60
martin p5m marlin
...d states navy performing naval patrols. it also served with the united states coast guard and the french navy. 285 were produced.
humster3d
$15
AMC Marlin 1965 Blueprint
...65 blueprint 3d model in the format you need. all our 3d models was created on real car base and maximally close to the original.
humster3d
$75
3D model of AMC Marlin 1965
...y a detailed 3d model of amc marlin 1965 in various file formats. all our 3d models were created maximally close to the original.
turbosquid
$20
Cartoon fish - Xiphias gladius - marlin
...phias gladius - marlin for download as max, 3ds, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1673408)
Firmware
3d_export
$5
Pepe stool by Opinion Ciatti Italian
...design provides a special slope. additional decor - manual firmware<br>32 x 48 x h58...
3d_export
$5
LENNY BED by Felis
...removable. an additional decor of the headboard is a firmware that imitates the capitonne technique. the bed can be...
thingiverse
free
sidewider x1 firmware by Xavierart26
...sidewider x1 firmware by xavierart26
thingiverse
firmware for sidewider x1
thingiverse
free
Sailfish Firmware by jetty
... created with omnomnom creator:http://www.thingiverse.com/thing:24639.
note: this is not an official makerbot firmware release.
thingiverse
free
Jetty Accelerated Firmware by jetty
...y-firmware#toc66
any updates will be placed here, so check back often.
note: this is not an official makerbot firmware release.
thingiverse
free
Sigma Türkçe firmware (marlin1.1) by Paarthurnax
...sigma türkçe firmware (marlin1.1) by paarthurnax
thingiverse
sigma türkçe firmware (marlin1.1)
thingiverse
free
firmware for orca 040 by sellemann
...y sellemann
thingiverse
firmware and settings for orca 040 with 025 nozzle
i had trubble getting it to work but now its working.
thingiverse
free
Gen4 Interface Firmware by jetty
...-firmware#toc66
any updates will be placed here, so check back often.
note: this is not an official makerbot firmware release.
thingiverse
free
cl-260 standard firmware (outdated!) by renoisenoir
...re is not for 2018 or higher version of cl-260!
this firmware is for 2016-version of cl-260
it can be used for reference purpose.
thingiverse
free
Firmware Tronxy XY2 Pro Titan by droidlex
...flashed your printer with marlin firmware, this should help restore the factory firmware, including the boot screen and interface