hexkey 12mm by Pokelia

...quadrocopter 12mm x 12mm leg by sq9mdd thingiverse quadrocopter 12mm x 12mm leg longer leg for fpv

...ole cover 12mm, furnitures by fernangus thingiverse just use glue to paste them. tapas 12mm mueble - hole cover 12mm, furnitures

...cube 12mm by gavin_v thingiverse 12mm cube

...axle holder 12mm by szatyi thingiverse 12mm

...z_axis 12mm by jcen517 thingiverse z_axis 12mm

...er / curtain holder 12mm by cappy0815 thingiverse gardinenhalter für 12mm gardinenstangen. curtainholder for 12mm gardine rails.

...12mm t bar clamp cf boom by dim3nsion thingiverse 12mm t bar clamp for 12mm cf booms

...ade the hole larger to 12mm. to fit my 12mm axle. update: added another 12.5mm. 12mm is too tight. could depend on your settings.

...clip for 12mm corrugated by gcastle2007 thingiverse clip for 12mm corrugated

...tube clamp 12mm by campilot thingiverse clamp for 12mm tubes

...rame update 1:53 pm made an slight error with....everything. i accidently scaled it when transferring it to stl. its fixed now :d

...er twice so you have it tightly secured (i use only one holder). will be work in progress until someone prints it and says its ok

...this yet. there is a cablehouse for thoose using corners from am8 project. its its 4cm to be put between rasp and electronic case

...in a nice case? check out the remix from pokelia its a rpi case in the same style as...

...darthcorvus thingiverse a nozzle set holder for any printers with 8mm frame. a hex keys holder for any printers with 8mm frame.

...n 6mm hexkey . diameter. 60mm height. 30mm depth of hole . 10mm will print it in pla as an manual crank for the hyperbolic gear .

... 2e64 thingiverse update: better fit this is hex key holder t50 t45 t40 t30 t27 t25 t20 t15 t10 print it 45deg slope! no support

...y set. suits 9 piece metrix set. as per : https://www.kincrome.com.au/key-wrench-set-9pce-metric?searchid=5216855&searchpos=9

...e of the allen key to the handle ultimate allen/hex key screw labeled handles by jimbo70https://www.thingiverse.com/thing:3635673

...nscad today, first what i make - holder for door magnetic lock controller for install it under table... my first experience... :)

...holder by surplace thingiverse vertical support with screw for hexkey holder hexkey holder -> https://www.thingiverse.com/thing:1661627 100% infill, no...

...by vanny thingiverse a handle to turn a normal inbuskey/hexkey into a handy...

...by andrewgowan thingiverse fits the most used size of hexkey in ftc. use the...

...quadrocopter 12mm x 12mm leg by sq9mdd thingiverse quadrocopter 12mm x 12mm leg longer leg for fpv

...cube 12mm by gavin_v thingiverse 12mm cube

...z_axis 12mm by jcen517 thingiverse z_axis 12mm

...l mount. extends the hex outwards 25mm if you would like me to remake this with a certain offset or extension length i can do so.

...ole cover 12mm, furnitures by fernangus thingiverse just use glue to paste them. tapas 12mm mueble - hole cover 12mm, furnitures

...12mm wrench by thehideousgourd thingiverse it's a wrench. it's 12mm.

...axle holder 12mm by szatyi thingiverse 12mm

...ade the hole larger to 12mm. to fit my 12mm axle. update: added another 12.5mm. 12mm is too tight. could depend on your settings.

...d thingiverse this is a 12mm stretcher, it prints nicely with no support in pla. message if another size is needed =] enjoy!