Thingiverse
HexaFloraDeLuz by jaln
by Thingiverse
Last crawled date: 3 years ago
This is a multi-color LED decor that will go for days on one CR2032 battery.
After trying to find a cheap LED base that works worth a darn, I finally gave up and created one that works reliably and doesn't cost a lot.
The base utilizes a coin, CR2032, battery holder and a multi-color LED T-1 bulb. Both were found on Amazon, as well as eBay, etc. The T-1 (3mm) bulb generally has a wider beam, 30 degrees, than a T-1 3/4 (5mm), and the leads are closer together which aids in this design.
The weak spot of most cheap LED mounts is the switch. This one uses the bulb itself as a switch. Could have made it more complex, but this works great. I have a few that have been running for more than 5 days, 24/7. At this point I do not know how long they will go.
The lampshade portion is an adaptation of a design I have not yet released called, HexaFloraVase. In order to get it to work here, I combined a solid and a surface into a single .STL file. I do not know if that will work for some folks. I use S3D and created a multiple process, solid with fill for the base, and single with no top and bottom layers for the part above the 31st layer. I will include the S3D gcode here as well for those that can use it. I use a .5 nozzle and .33 thick layers, transparent PETg at 240/75. With S3D I can change my temperatures when I print from the machine control window, so I can use different filament using the same gcode.
The base mounts the vertical coin holder base. The CR2032 holder is common. The fit is not real tight and you can glue it in if desired. The base press fits into the lampshade part.
To turn it on, insert a battery into the holder, and slip the bulb over the top edge of the battery. The longer bulb lead must be on the + side of the battery.
When not using the lamp, you can store the bulb in the two spare holes on the base. You can leave the batter in its holder because unless the bulb is on, it does not use any juice.
The two storage hold can also be used to straighten bent leads.
Try to keep the leads straight and close together. The spare/storage holes are a good gauge. If the bulb is put onto the battery with the leads reversed, it will not burn the bulb out. I just won't work. The reverse voltage is below it's burnout voltage.
Parts reference:https://www.amazon.com/Transparent-Lighting-Electronics-Components-Emitting/dp/B01C19ENH8/ref=pd_sim_60_2?_encoding=UTF8&refRID=2HT9HACZQS01WVZSEX11&dpID=31xGRHs9zvL&preST=_SY300_QL70_&dpSrc=detail&th=1
https://www.amazon.com/gp/product/B071F3HW8J/ref=oh_aui_detailpage_o01_s01?ie=UTF8&psc=1
https://www.amazon.com/Sony-CR2032-Lithium-Coin-Cell/dp/B008XBK7PG/ref=pd_bxgy_23_img_2?_encoding=UTF8&psc=1&refRID=XFYY4HMEBY4S3BPH2CEN&dpID=61yczfK5KTL&preST=_SX300_QL70_&dpSrc=detail
After trying to find a cheap LED base that works worth a darn, I finally gave up and created one that works reliably and doesn't cost a lot.
The base utilizes a coin, CR2032, battery holder and a multi-color LED T-1 bulb. Both were found on Amazon, as well as eBay, etc. The T-1 (3mm) bulb generally has a wider beam, 30 degrees, than a T-1 3/4 (5mm), and the leads are closer together which aids in this design.
The weak spot of most cheap LED mounts is the switch. This one uses the bulb itself as a switch. Could have made it more complex, but this works great. I have a few that have been running for more than 5 days, 24/7. At this point I do not know how long they will go.
The lampshade portion is an adaptation of a design I have not yet released called, HexaFloraVase. In order to get it to work here, I combined a solid and a surface into a single .STL file. I do not know if that will work for some folks. I use S3D and created a multiple process, solid with fill for the base, and single with no top and bottom layers for the part above the 31st layer. I will include the S3D gcode here as well for those that can use it. I use a .5 nozzle and .33 thick layers, transparent PETg at 240/75. With S3D I can change my temperatures when I print from the machine control window, so I can use different filament using the same gcode.
The base mounts the vertical coin holder base. The CR2032 holder is common. The fit is not real tight and you can glue it in if desired. The base press fits into the lampshade part.
To turn it on, insert a battery into the holder, and slip the bulb over the top edge of the battery. The longer bulb lead must be on the + side of the battery.
When not using the lamp, you can store the bulb in the two spare holes on the base. You can leave the batter in its holder because unless the bulb is on, it does not use any juice.
The two storage hold can also be used to straighten bent leads.
Try to keep the leads straight and close together. The spare/storage holes are a good gauge. If the bulb is put onto the battery with the leads reversed, it will not burn the bulb out. I just won't work. The reverse voltage is below it's burnout voltage.
Parts reference:https://www.amazon.com/Transparent-Lighting-Electronics-Components-Emitting/dp/B01C19ENH8/ref=pd_sim_60_2?_encoding=UTF8&refRID=2HT9HACZQS01WVZSEX11&dpID=31xGRHs9zvL&preST=_SY300_QL70_&dpSrc=detail&th=1
https://www.amazon.com/gp/product/B071F3HW8J/ref=oh_aui_detailpage_o01_s01?ie=UTF8&psc=1
https://www.amazon.com/Sony-CR2032-Lithium-Coin-Cell/dp/B008XBK7PG/ref=pd_bxgy_23_img_2?_encoding=UTF8&psc=1&refRID=XFYY4HMEBY4S3BPH2CEN&dpID=61yczfK5KTL&preST=_SX300_QL70_&dpSrc=detail
Similar models
thingiverse
free
Gun Vape Case by jbgibson87
...gm8cyjnx
update oct 23.2016
parts are now available for print. comment if there are any issues or suggestions for improvements.
thingiverse
free
Telescope finder scope mount by raptor_demon
...w=ysyi2&pd_rd_wg=figyo&psc=1&refrid=30m3mmwj0vg3h1dhrpxm&dpid=41bkdqitdkl&prest=_sx300_ql70_&dpsrc=detail
thingiverse
free
Manual Clothes Washer for Bucket by Puck
..._sbs_265_3?ie=utf8&dpid=21cfazidu8l&dpsrc=sims&prest=_ac_ul160_sr160%2c160_&psc=1&refrid=m45060154fv8ezg1x0ch
thingiverse
free
Curved Lithophane Holder by vbdcbrenner
..._s00?ie=utf8&psc=1
switch - https://www.amazon.com/gp/product/b07cg2vgwg/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=utf8&psc=1
thingiverse
free
Generic device car incd holder by tophe75
...=sims&prest=_ac_ul160_sr160%2c160_&refrid=0f7skyfxna7mwvak1s53)
145mm not tested with any device.
prints without support.
thingiverse
free
Porsche Lookalike Headlight Housings (For Fun, Not For Actual Car) by SILVERADORED
...mtoy-brilliant-led-projectors-projector/dp/b0184iyjva/ref=pd_day0_263_10?_encoding=utf8&psc=1&refrid=qnf5q475rxmd32h7kewg
thingiverse
free
Light Post by Gleeptoid7
...on.com/honbay-cr2032-button-battery-holder/dp/b072l6dg6f/ref=pd_ybh_a_27?_encoding=utf8&psc=1&refrid=vd56v7r04xy4q6se5gwq
thingiverse
free
Nexus 7 2013 wireless wall charger by gohan
...qa/ref=pd_sim_107_27?ie=utf8&dpid=418xvcfuj9l&dpsrc=sims&prest=_ac_ul160_sr160%2c160_&refrid=1esv8mkjdqayp3nqm6q5
thingiverse
free
Laser DL-44 by Dinoman217
...tubing-eventronic/dp/b072pcq2lw/ref=sr_1_5?s=industrial&ie=utf8&qid=1527956002&sr=1-5&keywords=heat+shrink+tubing
thingiverse
free
Gopro Clamp by theTeV
...rest=_ac_ul160_sr92%2c160_&psc=1&refrid=8wfbqqngrp7pgx7je1j5
fits all gopros hero3 hero4 hero2 and also aee s80 and so on
Hexafloradeluz
Jaln
thingiverse
free
Vase-X3 by jaln
...awn.
there are two sizes of this triangle to hex transition.
they are printed upside to insure that they stay stuck to the bed.
thingiverse
free
AmanteVase by jaln
...is especially useful when you are using pause to change filament colors. pausing on the inner wall will help conceal the change.
thingiverse
free
Vase-X4 by jaln
...t 100mm.
the smaller one is printed upside down for stability while printing.
this design is my favorite of this series.
enjoy!
thingiverse
free
Turbowlz II by jaln
...r the other designs to make your own designs.
lid knob made bigger on 01/22/15. deleted old file-- new file has a designation.
thingiverse
free
Turbo-Bowl: Turbo-Vase+, the Sequel Continues by jaln
...the sequel continues by jaln
thingiverse
here's some matching bowls for vase10a.
(turbo-vase+, the sequel).
scaled 1x and 2x
thingiverse
free
TurBowlz I by jaln
...ed .33mm layers, i am amazed that this even printed with no support!
a testament to lulzbot taz4 and gizmo dorks transparent abs.
thingiverse
free
BublaVase by jaln
... print job. not intentional, but i often recommend printing partial prints to make bowls from vases. some look great both ways.
thingiverse
free
Vase-X2 three versions by jaln
...previous vases were rotations, sweeps along splines, and boolean functions.
scale em, stretch em. have fun.
show us your work.
thingiverse
free
FlamoVase by jaln
...nt at about 30% of its full height, it makes a great screw on lid for the full print of the same scale. see the last two photos.
thingiverse
free
Vase-X1 by jaln
...ave slots. x3 is thicker.
the x1 in the photo was printed right side up and decided to leave the heated bed prior to completion.