Thingiverse
Hemera mount CR6 by RebelMD
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is a working Beta Release, these can be printed at .12 at least for the fan duct. I have included the firmware as well as the configuration files. Feel free to contribute to helping further modify the CR6 and other printing ventures visit my Patreon or PayPal me with a note.
The included firmware will be for both CR6 and CR6 Max, with BTT motherboard and display, as well as BTT board with Stock display, Stock boards with stock display.
Hardware:
-Hemera DD or Bowden
-M3 bolts and nuts(kit on amazon are cheap and always great to have laying around for tinkering)
-Lengths of PTFE tubing( I used Capricorn)
---Optional---
BTT Runout sensor
-Stock filament runoout for CR6(remove from stock housing, place in the one on the mount)
-Neopixels
Mounting instructions:
Remove the stock hot end assembly leaving the plate attached to the gantry.
1) Place the mount with the transfer board on the plat first, it will need 2-M3x6mm and 2-M3x16mm.( Wait until you have all the mounts and fan on the Hemera before running the 16mm screws through the strain gauge and into the gantry plate.)
1A) The stock CR6 runout sensor you take apart and place the pieces in the place the came from in the one on the mount. Place two M3 nuts inside the mount and use 2-M3x16mm screws to secure the cap to the runout sensor. You will need a piece of PTFE between the Hemera and sensor
1B) The BTT Smart Filament Runout Sensor you remove the rear panel and secure it to the mount using the screws you removed. You will need a piece of PTFE between the Hemera and sensor.
2) You will need to secure the strain gauge to the mount labeled HemeraMountV2 using 2-M3 nuts and 2-M3x8mm screws.
2A) Using the screws that came with your Hemera, secure file HemeraMountV2 to the Hemera.
3) The 5150 Winsinn fan works great for me and is fairly silent compared to stock CR6 fan. the mount can be attached to the Hemera with one the square nuts provided with the Hemera and 2-M3x4mm which can be found on the stock CR6 hot end. The fan slides in and is held in place by two M3x10mm screws like studs. (use a small screwdriver and poke a hole through then thread the screw through)
3A) For a white LED strip slide it in the rails under the fan duct and plug into the existing LED plug
-----Optional----
If you are using a BTT motherboard i will include a firmware for you as well to add a 5v flat neopixel strip under the fan duct for 4 LED which will change color as your machine warms up for a print and turns white as it prints. you will need to run a wire from the hot end, through the shrink around the ribbon cable, and into the RBG plug of the motherboard.
4) Using the above mentioned M3x16mm screws secure the Hemera to the gantry mount.
I cut a piece of PTFE to leave out of the top of my Hemera(Runout sensor if using one) to ease strain.
** I am still working on a cover to go around the Hemera and transfer board****
I will be releasing different versions stay tuned!
The included firmware will be for both CR6 and CR6 Max, with BTT motherboard and display, as well as BTT board with Stock display, Stock boards with stock display.
Hardware:
-Hemera DD or Bowden
-M3 bolts and nuts(kit on amazon are cheap and always great to have laying around for tinkering)
-Lengths of PTFE tubing( I used Capricorn)
---Optional---
BTT Runout sensor
-Stock filament runoout for CR6(remove from stock housing, place in the one on the mount)
-Neopixels
Mounting instructions:
Remove the stock hot end assembly leaving the plate attached to the gantry.
1) Place the mount with the transfer board on the plat first, it will need 2-M3x6mm and 2-M3x16mm.( Wait until you have all the mounts and fan on the Hemera before running the 16mm screws through the strain gauge and into the gantry plate.)
1A) The stock CR6 runout sensor you take apart and place the pieces in the place the came from in the one on the mount. Place two M3 nuts inside the mount and use 2-M3x16mm screws to secure the cap to the runout sensor. You will need a piece of PTFE between the Hemera and sensor
1B) The BTT Smart Filament Runout Sensor you remove the rear panel and secure it to the mount using the screws you removed. You will need a piece of PTFE between the Hemera and sensor.
2) You will need to secure the strain gauge to the mount labeled HemeraMountV2 using 2-M3 nuts and 2-M3x8mm screws.
2A) Using the screws that came with your Hemera, secure file HemeraMountV2 to the Hemera.
3) The 5150 Winsinn fan works great for me and is fairly silent compared to stock CR6 fan. the mount can be attached to the Hemera with one the square nuts provided with the Hemera and 2-M3x4mm which can be found on the stock CR6 hot end. The fan slides in and is held in place by two M3x10mm screws like studs. (use a small screwdriver and poke a hole through then thread the screw through)
3A) For a white LED strip slide it in the rails under the fan duct and plug into the existing LED plug
-----Optional----
If you are using a BTT motherboard i will include a firmware for you as well to add a 5v flat neopixel strip under the fan duct for 4 LED which will change color as your machine warms up for a print and turns white as it prints. you will need to run a wire from the hot end, through the shrink around the ribbon cable, and into the RBG plug of the motherboard.
4) Using the above mentioned M3x16mm screws secure the Hemera to the gantry mount.
I cut a piece of PTFE to leave out of the top of my Hemera(Runout sensor if using one) to ease strain.
** I am still working on a cover to go around the Hemera and transfer board****
I will be releasing different versions stay tuned!
Similar models
thingiverse
free
Filament Runout Sensor Housing with PTFE Couplers by michaelbourque
...lue holding the board down. reassemble into the new housing. screw in the two ptfe couplers and use m3 flat head screws to mount.
thingiverse
free
Ender 3 Pro 5015 Fan PSU Mount by DanHergie
...stock fan screws to secure the lid of the mount to the 5015.
finally use 2 x m3x5mm screws to firmly secure the lid to the mount.
thingiverse
free
dual 5015 fan duct for Hemera by ArcadeCarpet
... the hemera, you will need to use washers to get the right screw length. i've included the step files for easy modification.
thingiverse
free
BTT TFT35 V3 Mount for CR6 by 7Point4
...ncluded, one for the left side of the printer, and one for the right side. for use with the btt skr cr6 aftermarket motherboard.
thingiverse
free
Artillery Sidewinder/Genius Adjustable Height Fan Duct Mount With Bl-Touch by blinkybill
...you don't like the knob.
slide in the fan duct from the bottom to the desired height and tighten the knob.
buy me a coffee:
thingiverse
free
BTT Filament runout sensor for Micro Swiss Direct Drive by ptsiampas
...mount without the roller if you don't want to use it.
i have been using it for over 2 months and it's still going strong.
thingiverse
free
BTT SKR V1.4 Turbo Fan Duct by Bohncarlos
...ft side of the board (it, apparently, works better and makes less noise);
two with the fan @90° and right/left side of the board.
thingiverse
free
Simple filament runout sensor mount for Ender 3 Pro with direct extruder by qnub
...r.
from the input side if the mount you can insert 6mm tube from dryer or just put filament directly or through my filament guide
thingiverse
free
Filament runout sensor from Z enstop by Fixarn
...mount the sensor inside the house.
you also need two m3 nuts and you can fit ptfe tube in the holes om each side for a better fit
thingiverse
free
ADIMLab Gantry MGN12H Linear Rail Hemera Mount
... the mount with 4 x m3-6mm screws and uses a 5015 blower fan.
hotend wiring can run up the 10mm hole through the mount and block.
Rebelmd
thingiverse
free
Rail insert by RebelMD
...rail insert by rebelmd
thingiverse
covers i made for the extrusion to hide my neopixel wiring
thingiverse
free
PIRack by RebelMD
...ingiverse
these are my works in progress, bits of peoples ideas i've remixed into one idea that's continuously changing.
thingiverse
free
Cr6 Endstop With cable clip by RebelMD
...cr6 endstop with cable clip by rebelmd
thingiverse
cr6 endstop
thingiverse
free
CR6 Top of Z cover by RebelMD
...rebelmd
thingiverse
top end of z cover for cr6
print 2 short pins for the hole in top.
the washers and pulley pin for the roller
thingiverse
free
CR6-SE Sd to Micro adapter holder by RebelMD
...cr6-se sd to micro adapter holder by rebelmd
thingiverse
custom for print. havent made a test print yet
thingiverse
free
Pi case by RebelMD
...or to stack multiple pi. i left the sides open you can add a grill or you can leave them open like me for plexiglass and airflow.
thingiverse
free
Big Hemera CR6 by RebelMD
...n and pin file to run led on your printer.
3/27 edit
cr6 hemera mount can be found herehttps://www.thingiverse.com/thing:4779738
Cr6
3ddd
$1
Baga Emotional style CR6
...baga emotional style cr6
3ddd
baga
надеюсь кому-то пригодится :)
3ddd
$1
Светильник Baga
...3ddd baga , contemporary светильник подвесной ф. baga арт. cr6 ...
sketchfab
$50
Body CR6 Buggy
...ody cr6 buggy.
model developed for 3d print.
parts with fittings. - body cr6 buggy - buy royalty free 3d model by andreyraphael3d
thingiverse
free
Accessoire pour CR6 by jjfr
...accessoire pour cr6 by jjfr
thingiverse
pièce pour cr6 se
thingiverse
free
Cr6 Endstop With cable clip by RebelMD
...cr6 endstop with cable clip by rebelmd
thingiverse
cr6 endstop
thingiverse
free
CR6 SE Connector by p3ab0dy
... se connector by p3ab0dy
thingiverse
added a holder for the cr6 se arm. it slides in to the filament arm delivered with printer.
thingiverse
free
CR6-SE Handle by Arvi_G
...cr6-se handle by arvi_g
thingiverse
simple handle for cr6-se
requires longer m3 screw & nut to mount.
unity_asset_store
$15
SF Dreadnought CR6
...your workflow with the sf dreadnought cr6 asset from cgpitbull. find this & other space options on the unity asset store.
thingiverse
free
CR6-SE Tool Organizer by Taskino
...cr6-se tool organizer by taskino
thingiverse
a tool organizer for the creality cr6-se
thingiverse
free
CR6-SE Pi Mount by Baz_8755
...cr6-se pi mount by baz_8755
thingiverse
my first attempt at a raspbery pi mount for the creality cr6-se
Hemera
3ddd
$1
Hemera
...d
круглое , напольные
зеркало hemera;
designer:grace feyock
dimensions:46 w x 46 h x 1 d
3ddd
$1
Cофа (MOS)
...cофа (mos) 3ddd угловой hemera l-shape sofa. смоделена по реальным...
3d_sky
free
PROFI Hemera
...profi hemera
3dsky
hemera mirror;
designer: grace feyock
dimensions: 46 w x 46 h x 1 d
thingiverse
free
E3D Hemera Model
...e3d hemera model
thingiverse
official mounting cad for designing your own custom mounts for the e3d hemera.
thingiverse
free
Hemera Troodon mount by vonsy
...hemera troodon mount by vonsy
thingiverse
hemera support for troodon
thingiverse
free
BLTouch Mount for Hemera
...bltouch mount for hemera
thingiverse
attach to hemera heat sink body with 3m vhb tape flush to the top edge.
thingiverse
free
X5S MGN12 Hemera by Festivejelly
... mounting solution for the e3d hemera on a mgn12 rail.
assemble and screw the hemera into the mount before putting onto the rail.
thingiverse
free
Hemera Mount for 2020 (2040)
...hemera mount for 2020 (2040)
thingiverse
2020 mount for the e3d hemera (hermes)
thingiverse
free
MGN12 Toprail mount for Hemera
...mgn12 toprail mount for hemera
thingiverse
hemera mount for mgn12 rails on top like the am8
thingiverse
free
E3D Hemera Blower Duct
...e3d hemera blower duct
thingiverse
blower duct & mount. fits e3d hemera extruder
Mount
3d_export
free
mounting bracket
...mounting plate is the portion of a hinge that attaches to the wood. mounting plates can be used indoors, cabinetry and furniture.
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)