Thingiverse
Headphone Holder with Cable Management Spool Table Mount Version - with STEP file by registeredthing
by Thingiverse
Last crawled date: 4 years, 1 month ago
This is a desk mount headphone holder with a ratcheting cable spool.
The desk mount is remixed from philbarrenger's awesome "Monster Mouth Headphone Holder - Clampable" ( https://www.thingiverse.com/thing:1657541 ), and the rest is a remix of my "Wall Mount Headphone Holder with Cable Management Spool - VERSION 2" ( https://www.thingiverse.com/thing:4202518 ).
This thing will require:
2x M4 nuts
2x M4x12mm flat head bolts (It should be possible to use round head bolts with the newer design).
One 608zz bearing, which can be salvaged from an old fidget spinner.
One spring from a ball point pen
Two #8 flat head screws for wall mounting.
Optionally a rubber band, to quiet the gears. I tried a normal rubber band which was relatively thick and also a rubber band from a bunch of asparagus which worked a bit better but also added some resistance to turning.
Glue to secure the Clip on the back of the Base once everything is working.
To assemble:
First install the bearing on the reel. Using a second bearing to set the first bearing can help.
Then place the pen spring into the hole in the back of the base.
The sliding part will go in next, and capture one end of the spring. Ideally the spring action of the slider should be moderate and should not take much force to move it in the track. I'd say the pressure of the slider should be similar to the pressure of the cap on the pen the spring was removed from. If it does not move freely, remove the slider and try sanding the base and cleaning up the part a bit. I found that some of the springs I used were a bit too forceful, so I trimmed them to about 3/4 their original length, which worked well. It may take some trial and error in fitting with different pen springs or trimmed springs to get a good pressure from the slider. If the spring provides too much force, the reel will not be easy to turn and will be louder. Be careful of course with the springs and wear eye protection when installing them.
If you don't enjoy clickety click sounds, then now is a good time to install a rubber band on the geared teeth of the reel to quiet them down. Regular rubber bands seem to be a decent compromise between speed and noise, but a thicker band will quiet it more. There should be no twists in the band when it is installed. It should be possible to pop the reel off later and install the band if you find that it needs a thicker or thinner band (so far with the several prototypes I have made, I have been able to remove the reel without breaking it and change the bands without a problem).
Next, the "clip" can be installed on the back (see the pics - this is the green part shown on the back of the base). The clip will hold the slider in, and should snap into place securely. If it does not, then it probably needs to be cleaned up. There are very small cuts in the part which can be carefully cleaned up using a razor blade, and any foot on the part should be cleaned as much as possible. I found that printing this part without supports or any brim worked best. Same for the slider. Once everything is working as it should, add some glue to hold the clip in permanently, but be careful that the glue does not contact the slider. If the clip is not flush with the base, it should be sanded a bit to get it flat (otherwise there could be a small gap when the desk mount is attached.
Now the base would be be mounted to desk mount using the M4 nuts and bolts. You could also add glue at this point.
Finally, install the reel by pushing the installed bearing onto the post of the base. Note that the post will be a tight fit and once on, it probably won't come off the post without breaking - but it will probably still allow you to remove the reel since the reel should pop off the bearing. The slider may be in the way, but by angling the reel a bit during the installation, it should be possible to push it out of the way to set the reel in place.
Once it is assembled, test it by giving the reel a couple turns in both directions and make sure it all works. I found that the rubber band smooths out after several cycles.
Printing tips:
BASE: I printed the base with supports but used an overhang angle of 85% to avoid supports in the enclosed pockets. There is really only one place where the base needs supports and that is the flat area just above the opening in the back of the part. I printed the base using 0.2mm layer height.
REEL: I was able to print this without supports, though it was close. The arms of the reel may need to be supported but everything else should not need them. I printed the reel using 0.2mm layer height.
CLIP: Printed without supports and without a brim if possible to avoid the small gaps in the part merging together. I printed the clip using 0.12mm layer height.
SLIDER: CLIP: The latest version of this is already scaled to 99% of the original, but if it is not fitting well it may need to be scaled further. Print it without supports and without a brim if possible to avoid the small gaps in the part merging together. I printed the clip using 0.12mm layer height. This part should be glued in after it is fully test fitted and confirmed that everything works.
All parts were printed with 3 walls and 15% gyroid infill.
These are just what I used so as always, use your best judgement on what works for you and your printer, and good luck!
Parts are not oriented for printing. The STEP file is included for easy remixing.
Please post any makes and if you see a problem please post a comment.
The desk mount is remixed from philbarrenger's awesome "Monster Mouth Headphone Holder - Clampable" ( https://www.thingiverse.com/thing:1657541 ), and the rest is a remix of my "Wall Mount Headphone Holder with Cable Management Spool - VERSION 2" ( https://www.thingiverse.com/thing:4202518 ).
This thing will require:
2x M4 nuts
2x M4x12mm flat head bolts (It should be possible to use round head bolts with the newer design).
One 608zz bearing, which can be salvaged from an old fidget spinner.
One spring from a ball point pen
Two #8 flat head screws for wall mounting.
Optionally a rubber band, to quiet the gears. I tried a normal rubber band which was relatively thick and also a rubber band from a bunch of asparagus which worked a bit better but also added some resistance to turning.
Glue to secure the Clip on the back of the Base once everything is working.
To assemble:
First install the bearing on the reel. Using a second bearing to set the first bearing can help.
Then place the pen spring into the hole in the back of the base.
The sliding part will go in next, and capture one end of the spring. Ideally the spring action of the slider should be moderate and should not take much force to move it in the track. I'd say the pressure of the slider should be similar to the pressure of the cap on the pen the spring was removed from. If it does not move freely, remove the slider and try sanding the base and cleaning up the part a bit. I found that some of the springs I used were a bit too forceful, so I trimmed them to about 3/4 their original length, which worked well. It may take some trial and error in fitting with different pen springs or trimmed springs to get a good pressure from the slider. If the spring provides too much force, the reel will not be easy to turn and will be louder. Be careful of course with the springs and wear eye protection when installing them.
If you don't enjoy clickety click sounds, then now is a good time to install a rubber band on the geared teeth of the reel to quiet them down. Regular rubber bands seem to be a decent compromise between speed and noise, but a thicker band will quiet it more. There should be no twists in the band when it is installed. It should be possible to pop the reel off later and install the band if you find that it needs a thicker or thinner band (so far with the several prototypes I have made, I have been able to remove the reel without breaking it and change the bands without a problem).
Next, the "clip" can be installed on the back (see the pics - this is the green part shown on the back of the base). The clip will hold the slider in, and should snap into place securely. If it does not, then it probably needs to be cleaned up. There are very small cuts in the part which can be carefully cleaned up using a razor blade, and any foot on the part should be cleaned as much as possible. I found that printing this part without supports or any brim worked best. Same for the slider. Once everything is working as it should, add some glue to hold the clip in permanently, but be careful that the glue does not contact the slider. If the clip is not flush with the base, it should be sanded a bit to get it flat (otherwise there could be a small gap when the desk mount is attached.
Now the base would be be mounted to desk mount using the M4 nuts and bolts. You could also add glue at this point.
Finally, install the reel by pushing the installed bearing onto the post of the base. Note that the post will be a tight fit and once on, it probably won't come off the post without breaking - but it will probably still allow you to remove the reel since the reel should pop off the bearing. The slider may be in the way, but by angling the reel a bit during the installation, it should be possible to push it out of the way to set the reel in place.
Once it is assembled, test it by giving the reel a couple turns in both directions and make sure it all works. I found that the rubber band smooths out after several cycles.
Printing tips:
BASE: I printed the base with supports but used an overhang angle of 85% to avoid supports in the enclosed pockets. There is really only one place where the base needs supports and that is the flat area just above the opening in the back of the part. I printed the base using 0.2mm layer height.
REEL: I was able to print this without supports, though it was close. The arms of the reel may need to be supported but everything else should not need them. I printed the reel using 0.2mm layer height.
CLIP: Printed without supports and without a brim if possible to avoid the small gaps in the part merging together. I printed the clip using 0.12mm layer height.
SLIDER: CLIP: The latest version of this is already scaled to 99% of the original, but if it is not fitting well it may need to be scaled further. Print it without supports and without a brim if possible to avoid the small gaps in the part merging together. I printed the clip using 0.12mm layer height. This part should be glued in after it is fully test fitted and confirmed that everything works.
All parts were printed with 3 walls and 15% gyroid infill.
These are just what I used so as always, use your best judgement on what works for you and your printer, and good luck!
Parts are not oriented for printing. The STEP file is included for easy remixing.
Please post any makes and if you see a problem please post a comment.
Similar models
thingiverse
free
Wall Mount Headphone Holder with Cable Management Spool - VERSION 2
...i'd say the pressure of the slider should be similar to the pressure of the cap on the pen...
thingiverse
free
Headphone Holder with Cable Management Spool for Haworth Compose Cubicles - VERSION 2
...i'd say the pressure of the slider should be similar to the pressure of the cap on the pen...
thingiverse
free
Bag Clip by thatdude902
.... the two parts snap together. and just put the rubber band in there tight. the two parts can be printed with or without support.
thingiverse
free
Roland Drag Knife Holder by PROFDM1
...led it. the spring pressing on the "smaller" part applies pressure to the blade. the part dimensions should be in mm.
thingiverse
free
Working Gun Fully 3D Printed with spring and rubber band
...fully 3d printed with spring and rubber band
thingiverse
this is a working gun and you only need a pen spring and a rubber band
thingiverse
free
Cubetto flexible drawing addon
...two rubber bands in the pen mount (pencils or wax pens don't work that good, since there is no pressure on the pen)
have fun
thingiverse
free
Spring loaded Bed Leveler calibrator for Replicator or Flashforge by CodonExe
...ruler opening, may work without support. follow "the calibrator" instructions.
http://www.thingiverse.com/thing:62553
thingiverse
free
Headphone Holder with Cable Management Spool
...wall mounting.
the step file is included for easy remixing.
please post any makes and if you see a problem please post a comment.
thingiverse
free
Moosoo K17U Vacuum Replacement Clip by bastibeckr
...nd created a new one.
prints without supports in ~ 10mins, no special settings. add a pen spring and it works like the original.
thingiverse
free
Steam Controller Adjustable Phone Mount by DAVE42
...you need to use cura's "support blocker" or something similar in order to remove the supports inside hole where...
Registeredthing
thingiverse
free
Beads for a bracelet or whatever by registeredthing
...ot be needed. if you make one please post a make, if you have a suggestion please post a comment. good luck and happy printing!
thingiverse
free
Mini Magnet Hardware Pickup Tool by registeredthing
...net may also work. the magnet goes into the tool about 5mm.
part is not oriented for printing but should print without supports.
thingiverse
free
15/32" Drill Bit Case by registeredthing
...rs.
this was designed using viacad v12 pro
step file is included for easy remixing and the parts are not oriented for printing.
thingiverse
free
Under Desk Headphone Holder by registeredthing
...ut may help with positioning it under a desk.
if you print one, please post a make. step file is included for easy remix'in.
thingiverse
free
Number 8 Screw Cover or Cap by registeredthing
...t you will test the prototypes and provide feedback (i don't like to spend the pla on testing stuff i don't plan to use).
thingiverse
free
BLTouch Mount Ender 5
...cut a small hole in the bltouch mount by registeredthing to fit it on the creality ender 5 extruder...
thingiverse
free
Towel Holder | Handtuchhalter (REMIX) for 3M Command Strips by registeredthing
...a door it is placed next to).
step file is included, and the parts may need to be oriented for printing (no supports are needed).
thingiverse
free
Clorox Wipes Holder - Wall Mount (WORK IN PROGRSS) - With STEP file by registeredthing
... hurt. 2x mounting screws will also be needed.
if you make one and have feedback please let me know so i can improve this model.
thingiverse
free
Clorox Wipes Holder - Cube Mount for Haworth Compose (WORK IN PROGRSS) - With STEP file by registeredthing
...onal (to hold the nuts in) but can't hurt.
if you make one and have feedback please let me know so i can improve this model.
thingiverse
free
Sony Headphones Strain Relief Boot (Sony MDR-V6) by registeredthing
...erse.com/thing:4662709
part is not oriented for printing (rotate so the larger end is down).
if you make one, please post a make.
Headphone
3d_export
$5
headphones
...headphones
3dexport
ordinary headphones.. ordinary black headphones.
3d_ocean
$6
headphones
...headphones
3docean
computer headphones music
stylish headphones with leather lining
3d_export
$10
Headphones
...headphones
3dexport
headphones
3d_export
$5
headphones
...headphones
3dexport
headphones
3d_ocean
$8
Headphone
...headphone
3docean
3d model equipment headphone music
3d headphones with autodesk maya, 3d model, headphone, equipment, music
3d_ocean
$15
headphone
...headphone
3docean
audio cinema4d headphone
headphone max c4d obj model
3d_export
$5
headphones
...headphones
3dexport
they are golden headphones
archibase_planet
free
Headphones
...hones earphone headphone earphones
headphones panasonic rp wf810h n040111 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
headphones
...headphones
3dexport
lowpoly model headphones
3d_export
$26
headphones
...headphones
3dexport
low poly model headphones
Management
vizpark
$10
Material Manager
...ager
vizpark
the vp material manager is a new innovative tool to manage materials within 3ds max® in ways never possible before.
vizpark
free
Material Manager
...ager
vizpark
the vp material manager is a new innovative tool to manage materials within 3ds max® in ways never possible before.
3d_export
$6
management desk
...management desk
3dexport
quality table object with chairs for office and management space
3d_ocean
$5
Manager table
...manager table
3docean
office manager table. including dxf, obj, 3ds max file with maps.
turbosquid
$10
Eddie the manager
...
royalty free 3d model eddie the manager for download as max on turbosquid: 3d models for games, architecture, videos. (1344924)
turbosquid
$5
Manager Desk
...uid
royalty free 3d model manager desk for download as blend on turbosquid: 3d models for games, architecture, videos. (1435584)
turbosquid
$4
manager room
...squid
royalty free 3d model manager room for download as max on turbosquid: 3d models for games, architecture, videos. (1616151)
turbosquid
$5
Manager desk
...lty free 3d model manager desk #2 for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1304731)
turbosquid
$5
Manager desk
...lty free 3d model manager desk #3 for download as max and obj on turbosquid: 3d models for games, architecture, videos. (1304733)
turbosquid
$10
Modular Cable manager
...yalty free 3d model modular cable manager for download as fbx on turbosquid: 3d models for games, architecture, videos. (1402372)
Spool
3ddd
$1
spool c53301
...spool c53301
3ddd
spool
spool c53301 650х350х145
turbosquid
$3
Cable Spool
...royalty free 3d model cable spool for download as max and fbx on turbosquid: 3d models for games, architecture, videos. (1457009)
turbosquid
free
Pallets and Spool
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Spool of String
...ol of string pink for download as c4d, 3ds, fbx, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1647892)
3ddd
$1
Подвесные светильники Spool
...ye/podvesnoy_svetilnik_spool_d320/ http://www.cosmorelax.ru/catalog/podvesnyye/podvesnoy_svetilnik_spool_d420/
3ddd
free
Spool 001 sofa
...spool 001 sofa
3ddd
roda
roda
collection spool
design rodolfo dordoni
dimensions:
lenght 90 cm
depth 94 cm
height 79 cm
turbosquid
$15
Roda Spool Sofa
...ee 3d model roda spool sofa for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1502650)
turbosquid
$95
wire spools 3ds
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$20
spool of TV wire
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$3
Simple and Fast Spool Holder
...ree 3d model simple and fast spool holder for download as stl on turbosquid: 3d models for games, architecture, videos. (1548546)
Step
3ddd
free
Pro Seda Step by Step
... by step
3ddd
step , proseda , кушетка
pro seda
design_connected
$9
Step
...step
designconnected
porada step coffee tables computer generated 3d model. designed by tarciso colzani.
turbosquid
$49
Steps
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$30
step
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$11
Step
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$20
Folding steps step stool 3D Model
...tool stepstool steps ladder tool tools garage workshop shed basement
folding steps step stool 3d model pixelblock 43270 3dexport
3d_export
$5
Glass steps
...glass steps
3dexport
well, just glass steps
3ddd
$1
Lago Steps
...lago steps
3ddd
lago
lago steps chair.
3d_export
$10
steps with cocrete
...steps with cocrete
3dexport
design steps for the architecture engineering purpose
archibase_planet
free
Rack step
...rack step
archibase planet
rack step rack gym
rack step - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
Cable
3d_export
free
Cables
...cables
3dexport
cables for your purposes
3d_export
free
cable belt for cable organization
...ze your cables in 3d printers. it will bend only to one direction. the area to put the cables per piece is aprox. 1,6cmx2,6cmx1cm
3d_ocean
$16
Ethernet Cable
...ethernet cable
3docean
cable computer electronics ethernet internet network connected
ethernet cable 3d model
3d_export
$65
cable
...cable
3dexport
simple rendering of the scene file
turbosquid
$14
Cable
...l cable for download as ma, max, fbx, 3ds, gltf, obj, and stl on turbosquid: 3d models for games, architecture, videos. (1631358)
3ddd
$1
Cable Cover
...cable cover
3ddd
кабель
vertebra passacavo - cable cover
max + vray 2.20.03
3d_export
$15
Cable reel
...without cable. textures 4k 4096x4096 targa, png, jpeg.<br>number of polygons without cable: 2896<br>with cable: 35328
3d_export
$7
short cable
...short cable
3dexport
rubber cord. very detailed. cable thickness: 2.55 mm total length: 55mm
3d_export
$5
USB CABLE
...usb cable
3dexport
turbosquid
$30
Cable Reels
...osquid
royalty free 3d model cable reels for download as fbx on turbosquid: 3d models for games, architecture, videos. (1439507)
Holder
archibase_planet
free
Holder
...holder
archibase planet
holder toilet paper holder
holder paper n070712 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...e planet
holder rack toilet paper holder
holder toilet roll n240715 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
pen holder support prop
pen holder - 3d model for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
pole post holder
сhurch cross pole holder - 3d model for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder bathroom ware
shower holder - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...oilet paper holder
holder paper devon&devon; time black n241113 - 3d model (*.gsm+*.3ds+*.max) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder hanger hanger for towel
holder 7 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder hanger hanger for towel
holder 3 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...holder
archibase planet
holder towel rack towel-horse
holder - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Holder
...lder
archibase planet
holder hanger hanger for towel
holder towel n250912 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Mount
3d_export
free
mounting bracket
...mounting plate is the portion of a hinge that attaches to the wood. mounting plates can be used indoors, cabinetry and furniture.
turbosquid
$2
MOUNTING
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mounts
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
free
Mount Fuji
...fuji
turbosquid
free 3d model mount fuji for download as obj on turbosquid: 3d models for games, architecture, videos. (1579977)
3d_export
$5
Headphone mount LR
...headphone mount lr
3dexport
headphone mount l+r
turbosquid
$39
Mount rainier
...quid
royalty free 3d model mount rainier for download as fbx on turbosquid: 3d models for games, architecture, videos. (1492586)
turbosquid
$5
pipe mounting
...quid
royalty free 3d model pipe mounting for download as obj on turbosquid: 3d models for games, architecture, videos. (1293744)
turbosquid
$3
Mounting Tires
...uid
royalty free 3d model mounting tires for download as fbx on turbosquid: 3d models for games, architecture, videos. (1708511)
3d_export
$5
Magnetic GoPro Mount
...pro mount
3dexport
cool magnetic mount for gopro. allows you to mount the camera on flat metal surfaces and get exclusive shots.
turbosquid
$5
Stone Mount
...ty free 3d model stone mount for download as ma, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1370306)
Table
3ddd
free
Table
...table
3ddd
table
table
archibase_planet
free
Table
...table
archibase planet
table glass-table round table glass table
table n240311 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Table
...e
archibase planet
table dining-room table dinner table round table
table - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$5
table
...table
3dexport
table classic-table
archibase_planet
free
Table
...se planet
table glass table round table glass-table
table tonin habitat n280111 - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Table
...table
archibase planet
table dining-room table dinner table
table - 3d model (*.3ds) for interior 3d visualization.
archibase_planet
free
Table
...table
archibase planet
table coffee table glass table
table - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Table
...table
archibase planet
table glass-table coffee table
table - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archibase_planet
free
Table
...table
archibase planet
table writing table office table
table - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_ocean
$5
Table
...table
3docean
dining table furniture home kitchen table
simple wooden table.
Version
3ddd
$1
Diamond version
...nd , version , ванна
visionnaire - diamond bath
turbosquid
$50
LibraryMini Version
...free 3d model librarymini version for download as max and jpg on turbosquid: 3d models for games, architecture, videos. (1617724)
design_connected
$34
Barocco Version 01
...barocco version 01
designconnected
zanotta barocco version 01 computer generated 3d model. designed by progetti, emaf.
design_connected
$27
Barocco Version 02
...barocco version 02
designconnected
zanotta barocco version 02 computer generated 3d model. designed by progetti, emaf.
turbosquid
free
Door [2 versions]
...rbosquid
free 3d model door [2 versions] for download as fbx on turbosquid: 3d models for games, architecture, videos. (1223985)
turbosquid
$2
seat version 0.1
...
royalty free 3d model seat version 0.1 for download as blend on turbosquid: 3d models for games, architecture, videos. (1432653)
turbosquid
$12
Chip Version 03
...lty free 3d model chip version 03 for download as c4d and fbx on turbosquid: 3d models for games, architecture, videos. (1241145)
3d_export
$10
magnolia grandiflora mature version
...magnolia grandiflora mature version
3dexport
magnolia grandiflora mature version
3d_export
$8
room assets and voxel version
...room assets and voxel version
3dexport
room assets and voxel version
turbosquid
$35
Zil Civilian version
... model zil civilian version for download as cgf, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1639420)
File
archibase_planet
free
File
...file
archibase planet
locker box archive
fp suspension file wh - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
free
File
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_ocean
$5
Filing cabinet
...filing cabinet 3docean cabinet chair desk file filing locker office paper storage store work a simple...
turbosquid
$8
Filing cabinets
...id
royalty free 3d model filing cabinets for download as fbx on turbosquid: 3d models for games, architecture, videos. (1371140)
turbosquid
$8
File Cabinet
...squid
royalty free 3d model file cabinet for download as fbx on turbosquid: 3d models for games, architecture, videos. (1572208)
turbosquid
$16
Filing Cabinet
...ree 3d model filing cabinet for download as max, obj, and fbx on turbosquid: 3d models for games, architecture, videos. (1310873)
turbosquid
$2
File Cabinet
... free 3d model file cabinet for download as obj, c4d, and fbx on turbosquid: 3d models for games, architecture, videos. (1357577)
turbosquid
$12
Nail File
...e 3d model nail file for download as blend, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1588508)
turbosquid
$5
File Organiser
...model file organiser for download as blend, obj, fbx, and dae on turbosquid: 3d models for games, architecture, videos. (1636447)
turbosquid
$1
Flat file
...e 3d model flat file for download as 3ds, obj, md3, and blend on turbosquid: 3d models for games, architecture, videos. (1209808)