Thingiverse
Hardinge TL10 follow rest by Weldingrod1
by Thingiverse
Last crawled date: 3 years ago
This is a welded follow rest to fit a Hardinge TL-10 lathe. Feel free to adjust it to fit other lathes! It is designed to be cut from 1/4" plate using plasma cutting, though waterjet and laser would work fine too. CNC would also work.
The key to success on this is to pay attention to the cut-off tabs and leave them in place till you finish welding. Start by cleaning all the slag off your parts and grinding to bare metal any place you will be welding. Stack up the front and back plates and line them up carefully. Clamp them at least 4 places and then tack at least 6 places. DO NOT weld in the finger slots! Weld up all the edges EXCEPT where the brace fits in the corner. If you are going to mill the slots, go ahead and do it now. You can remove the tabs now if you want to. On mine, I used 1" x 3/8" cold rolled steel for the fingers, though the plasma cut fingers would have worked fine. Please be aware if you cut the finger slots a little deeper than 1/4", you will later have to mill the end of the back finger a bit thinner; otherwise it will catch on the two front fingers.
After doing any finish work on the slots, weld the foot and brace in place, and smooth all corners. Try to get the foot square to the front/back assembly.
You need the foot to be flat. After welding and grinding, you can either create a flat surface on it by putting epoxy on the foot and setting it on a flat surface that has been treated with mold release, or mill it flat. I milled it, then had some fun scraping it even flatter.
The three bolts to hold the fingers are 3/8"-16. The holes are undersize so that you can drill them to size and ensure they are round.
In use, move the follow rest as close to the headstock as possible, and slide each finger firmly against the work piece, and clamp them in place. Lube the work/fingers regularly.
I don't recommend using rollers on these; they will tend to suck chips in and either ding or bump the work. Tried it...
The key to success on this is to pay attention to the cut-off tabs and leave them in place till you finish welding. Start by cleaning all the slag off your parts and grinding to bare metal any place you will be welding. Stack up the front and back plates and line them up carefully. Clamp them at least 4 places and then tack at least 6 places. DO NOT weld in the finger slots! Weld up all the edges EXCEPT where the brace fits in the corner. If you are going to mill the slots, go ahead and do it now. You can remove the tabs now if you want to. On mine, I used 1" x 3/8" cold rolled steel for the fingers, though the plasma cut fingers would have worked fine. Please be aware if you cut the finger slots a little deeper than 1/4", you will later have to mill the end of the back finger a bit thinner; otherwise it will catch on the two front fingers.
After doing any finish work on the slots, weld the foot and brace in place, and smooth all corners. Try to get the foot square to the front/back assembly.
You need the foot to be flat. After welding and grinding, you can either create a flat surface on it by putting epoxy on the foot and setting it on a flat surface that has been treated with mold release, or mill it flat. I milled it, then had some fun scraping it even flatter.
The three bolts to hold the fingers are 3/8"-16. The holes are undersize so that you can drill them to size and ensure they are round.
In use, move the follow rest as close to the headstock as possible, and slide each finger firmly against the work piece, and clamp them in place. Lube the work/fingers regularly.
I don't recommend using rollers on these; they will tend to suck chips in and either ding or bump the work. Tried it...
Similar models
thingiverse
free
Hardinge lathe chuck holder by Weldingrod1
...t, and turn to lock. they are not particularly tight, though. the lock pin will ensure your chucks don't slide off, though.
grabcad
free
Hardinge steady rest, (works for other tool room lathes too.)
...and toolroom lathes. requires another part to be bolted to it. i use a brass disk to be drilled to size to steady the material.
grabcad
free
pegs
...pegs
grabcad
you can rest your foot on them and grind.
thingiverse
free
Single Edge Blade Holders by Bob99
... balsa and paper where a diy'er would want to hold the blade at 45 degrees and press while cutting with the tip of the blade.
thingiverse
free
Vive base station wall mount 3M command strip by rogueqd
...the screw holes are shaped to snap in and remain there. you need to break at least one of these tabs to remove the backing plate.
thingiverse
free
Hanging Planter (sheet metal) by 3DMakerMarket
.... mild steel, tack welded the bends in place, and spray painted it black.
please message me if you would like a modified version.
grabcad
free
Deskshelf Peace
...ck need to be mirrored, so that the deco comes on the outside. then tabs on the middle shelf has to be adjusted to new positions.
thingiverse
free
X-Carve Dust Rails Sides/Front/Back by drandolph
...or laser cut out the side plates and front/rear plate.
54 m3-10mm bolts
36 m3 drop-in extrusion nuts 2020 size
18 m3 regular nuts
cg_trader
$20
Hardinge HLV-H Lathe
...hardinge hlv-h lathe
cg trader
hardinge hlv-h lathe 1960 model.
grabcad
free
desk rack
...ng the connection slots and grinding smooth. anodizing is always the best option in my eyes last longer and gives a great finish.
Tl10
thingiverse
free
Taper Attachment for Hardinge TL10 lathe by Weldingrod1
...g area if you don't have a scale.
please keep in mind; these parts will not be strong enough for actual operation on a lathe!
grabcad
free
ALFA LAVAL TL10-BFG
...alfa laval tl10-bfg
grabcad
plate heat exchanger
3dwarehouse
free
Less TL10
.... tl5: 100x100cm. tl10: 230x100cm #jean_nouvel #less #mesa #molteni #nouvel #stół #table #taula #tavolo #tish #unifor #стол #テーブル
3dwarehouse
free
Team Lotus-Cosworth GPworld series
...f1 team. the name of the car is the tl10----for the 2011 season, lotus are forced to change there...
Hardinge
thingiverse
free
Hardinge lathe chuck holder by Weldingrod1
...t, and turn to lock. they are not particularly tight, though. the lock pin will ensure your chucks don't slide off, though.
thingiverse
free
Taper Attachment for Hardinge TL10 lathe by Weldingrod1
...g area if you don't have a scale.
please keep in mind; these parts will not be strong enough for actual operation on a lathe!
thingiverse
free
Gear set for cutting 10 pitch on a Hardinge TL by Weldingrod1
... good idea. i was able to cut the 10 pitch aluminum thread i needed using these without any visible damage on the teeth or bore.
cg_trader
$20
Hardinge HLV-H Lathe
...hardinge hlv-h lathe
cg trader
hardinge hlv-h lathe 1960 model.
grabcad
free
Hardinge HLV H Lathe
...hardinge hlv h lathe
grabcad
a hardinge hlvh.
please note this model is neither complete nor completely accurate.
grabcad
free
Hardinge HLV-H Lathe Spindle Nose Cover
...h lathe spindle nose cover
grabcad
almost all hardinge lathes are missing the cover to protect the spindle nose. print your own!
grabcad
free
Hardinge 16C Collet - 3mm Square
...c collet - 3mm square
grabcad
reverse engineer of 16c round collet
for cnc workpiece holding
this is a metric 3mm square version
cg_trader
free
Hardinge 16C Collet - 3mm Square
...collet - 3mm square
cg trader
reverse engineer of 16c round collet
for cnc workpiece holding
this is a metric 3mm square version
grabcad
free
Hardinge steady rest, (works for other tool room lathes too.)
...and toolroom lathes. requires another part to be bolted to it. i use a brass disk to be drilled to size to steady the material.
Weldingrod1
thingiverse
free
Cowboy Boot by Weldingrod1
...verse
i needed a model of a cowboy boot so i could wrap something to go with a "get a new pair of boots" certificate.
thingiverse
free
Christmas tree topper/star by Weldingrod1
...christmas tree topper/star by weldingrod1
thingiverse
this is a stellated dodecahedron to fancy up your tree!
thingiverse
free
Drying stand for nasal irrigator by Weldingrod1
...d for nasal irrigator by weldingrod1
thingiverse
this is a stand that fits the neilmed nasal irrigator and allows it to drip dry
thingiverse
free
Hand Punch Hangers by Weldingrod1
...omized to fit the two smaller sizes of whitney brand hand punches. the smaller one will fit the harbour freight hand punch also.
thingiverse
free
Stackable extruder by Weldingrod1
...s (oriented for the huxley) and are arranged to be stackable. the one that takes markers would, of course, use white filament...
thingiverse
free
Emaker Huxley electronics enclosure by Weldingrod1
...d to work with the emaker huxley electronics. it clears the sd card and accomodates the connector orientation used on the huxley
thingiverse
free
Milwaukee close quarters drill hangar by Weldingrod1
...od1
thingiverse
this is a custom fitted hangar for a milwaukee close quarters drill. it will probably fit the other brands too.
thingiverse
free
Y belt clamp with end stop by Weldingrod1
...y weldingrod1
thingiverse
if you replace your y axis belt clamp with this it will provide a place for the limit switch to touch.
thingiverse
free
Indicator Holder for Emaker Huxley print head by Weldingrod1
...huxley print head by weldingrod1
thingiverse
this will let you mount a test indicator on your huxley to really level up the bed!
thingiverse
free
Tape hangars by Weldingrod1
...ts and double units. the double unit is sized for two full size rolls to fit properly.
they stick up nicely with command strips.
Rest
3d_export
$5
rest table
...rest table
3dexport
rest table
3d_ocean
$8
Rest Case
...f most complete 3d application available. the “rest case” is available at blend format and obj format. open the blend file you...
3ddd
$1
Muuto Rest Sofa
...muuto rest sofa
3ddd
muuto , rest
muuto rest sofa
3ddd
$1
Muuto - Rest sofa
...muuto - rest sofa
3ddd
muuto , rest
muuto - rest sofa
design_connected
$16
Rest Lounger
...rest lounger
designconnected
kristalia rest lounger computer generated 3d model. designed by harry & camila.
3ddd
$1
Armchair Rest
...armchair rest
3ddd
nube italia
nube. armchair resthttp://www.nubeitalia.it/eng/armchairs/rest-2/
turbosquid
$10
Banana rest
...urbosquid
royalty free 3d model banana rest for download as on turbosquid: 3d models for games, architecture, videos. (1643978)
3ddd
free
The Rest chair by ESO
...the rest chair by eso
3ddd
rest , eso
the rest chair by eso.
750 mm х 620 mm
turbosquid
$25
rest sauce
...bosquid
royalty free 3d model rest sauce for download as fbx on turbosquid: 3d models for games, architecture, videos. (1239547)
turbosquid
$5
POTATO RESTING
...uid
royalty free 3d model potato resting for download as max on turbosquid: 3d models for games, architecture, videos. (1201599)
Follow
3d_export
$8
Cam and Follower
...ry to linear (reciprocating) motion. as the cam rotates, the follower rises and falls in a process known as reciprocating motion.
3ddd
$1
Follow Me
...follow me
3ddd
marset
http://www.marset.com/en/products/decorative/table/785-follow-me
turbosquid
$35
Follow Spot
...osquid
royalty free 3d model follow spot for download as fbx on turbosquid: 3d models for games, architecture, videos. (1682821)
turbosquid
$1
Follower - V8 Engine
...follower - v8 engine for download as ige, obj, stl, and sldpr on turbosquid: 3d models for games, architecture, videos. (1238716)
3d_export
$8
Four Sliding Follower Mechanism
...b and carry pins b which slide along grooves a. when cam 1 is turned through a certain angle, followers 2 slide along their axes.
turbosquid
$1
Form Follows Function Table by Daan Mulder
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
figure 8 follow knot
...>this model is too small and suitable for earring or piercing and it can be rescale up to what ever you want<br>enjoy it
cg_studio
$45
Honda cr-v 2013 Apron Follow me3d model
...t vehicle other
.max - honda cr-v 2013 apron follow me 3d model, royalty free license available, instant download after purchase.
3d_export
free
old building
...old building 3dexport follow the link for many free 3d...
3d_export
$15
Design bike
...design bike 3dexport design bike in the followng formats .obj .blender...