Thingiverse
"HaloDoggy"_StretchedPlus_BrushlessMicroDrone by MadR13D
by Thingiverse
Last crawled date: 3 years ago
V 3
Still untested. I'm working on this again. Shrinking it so it can be printed on a smaller 120mm x 120mm printer bed.
New: One piece print version? I saw this vid on YouTube where the guy shows that printing PLA at an angle makes for way stronger prints - for RC car parts.
I'm anxious to try this with this design. Instead of having all these different parts that fit together with screws. Why not just one piece for the whole frame? As long as the Flight controller can fit in there.
Will test print this when I'm done printing some other stuff. Soon.
Concept Notes:
This is my experimental brushless micro drone design. It is a stretched plus configuration, but I made the props on different levels. Stepped? That's what I think that should be called if it doesn't already have a name. Is that ok for flight? I saw that on a quad x design, I bought a frame from ebay like that recently. Haven't tested either yet!
One of the main goals of this build is to not have the propellers in the view, as well as to do something different that looks cool, and might be easier for me to tell which way its facing when flying it "freestyle?" Without the FPV feature. (I Plan on having the camera attached with a small plug so I can unplug it to save battery power if not using the FPV.
Even though I did a great deal of research about this I am still guessing on some stuff. What angle do quadcopters even fly at while moving forward? Is it 45? Note: A focus of this design was to get the propellers out of the view and still have the camera pointing straight ahead? I do plan on making the camera mount adjustable.
Parts List: (Note I bought a parts kit from Aliexpress. Search for "brushless micro drone kit". I put a picture of what the parts look like. Planning to design my own propeller guards for whenever any of these break.)
4* BE1104 7500kv Mini Brushless Motors - I think I'm going to use these different ones than in the image. (I've also included two files for bigger 1306 motors).
1* 2" 2.5" Propellers Guard Bumper Props Protector (Green or Blue)
1* 2 Pairs 2035 Propeller 2.0 inch 50.8mm PC Props 5-Blade CW CCW Paddle (Green or Blue)
1* Q25 MINI VTX+CAMERA 25mw 16ch Transmitter 800tvl coms Camera
(Tested this, major drop outs with my cheap usb receiver. Will most likely use a better one.)
1* PIKO Mini BLX F3 Flight Control Tower 4 in 1 BLheIS 10A 2~3s ESC
(Actually I don't recommend this one for beginner soldering people. I broke one! The motor points are just so darn small and close together. I have a very small soldering tip and a good iron station. Will be using something else!
Nylon or metal standoffs 30mm x 8. (16 bolts/screws for such). One thing nice about the parts kit, it had more than enough mounting hardware to design my frame thicknesses around.
Peace, and happy safe printing and flying!
Still untested. I'm working on this again. Shrinking it so it can be printed on a smaller 120mm x 120mm printer bed.
New: One piece print version? I saw this vid on YouTube where the guy shows that printing PLA at an angle makes for way stronger prints - for RC car parts.
I'm anxious to try this with this design. Instead of having all these different parts that fit together with screws. Why not just one piece for the whole frame? As long as the Flight controller can fit in there.
Will test print this when I'm done printing some other stuff. Soon.
Concept Notes:
This is my experimental brushless micro drone design. It is a stretched plus configuration, but I made the props on different levels. Stepped? That's what I think that should be called if it doesn't already have a name. Is that ok for flight? I saw that on a quad x design, I bought a frame from ebay like that recently. Haven't tested either yet!
One of the main goals of this build is to not have the propellers in the view, as well as to do something different that looks cool, and might be easier for me to tell which way its facing when flying it "freestyle?" Without the FPV feature. (I Plan on having the camera attached with a small plug so I can unplug it to save battery power if not using the FPV.
Even though I did a great deal of research about this I am still guessing on some stuff. What angle do quadcopters even fly at while moving forward? Is it 45? Note: A focus of this design was to get the propellers out of the view and still have the camera pointing straight ahead? I do plan on making the camera mount adjustable.
Parts List: (Note I bought a parts kit from Aliexpress. Search for "brushless micro drone kit". I put a picture of what the parts look like. Planning to design my own propeller guards for whenever any of these break.)
4* BE1104 7500kv Mini Brushless Motors - I think I'm going to use these different ones than in the image. (I've also included two files for bigger 1306 motors).
1* 2" 2.5" Propellers Guard Bumper Props Protector (Green or Blue)
1* 2 Pairs 2035 Propeller 2.0 inch 50.8mm PC Props 5-Blade CW CCW Paddle (Green or Blue)
1* Q25 MINI VTX+CAMERA 25mw 16ch Transmitter 800tvl coms Camera
(Tested this, major drop outs with my cheap usb receiver. Will most likely use a better one.)
1* PIKO Mini BLX F3 Flight Control Tower 4 in 1 BLheIS 10A 2~3s ESC
(Actually I don't recommend this one for beginner soldering people. I broke one! The motor points are just so darn small and close together. I have a very small soldering tip and a good iron station. Will be using something else!
Nylon or metal standoffs 30mm x 8. (16 bolts/screws for such). One thing nice about the parts kit, it had more than enough mounting hardware to design my frame thicknesses around.
Peace, and happy safe printing and flying!
Similar models
thingiverse
free
Propellers for heavy lift drones. print with carbon fiber filament, 300mm props by etasinetas
...t was designed to be printed with carbon fiber filament, protopasta, and driven with a brushless 370kv motor, i hope you like it.
thingiverse
free
Propellers for heavy lift drone, two blades, 300mm props by etasinetas
...t was designed to be printed with carbon fiber filament, protopasta, and driven with a brushless 600kv motor, i hope you like it.
thingiverse
free
2" prop guard by ReadTheFactoryManual
...rymanual
thingiverse
this is a propeller guard / space for the 1104-kv7500 brushless motors. this is designed for a 2" prop
thingiverse
free
Brushless Prop Guard (1.9" Propeller) by Nico_FPV
...rse
based on mcooz's mantis85 motor guard, but modified to clear 1.9" props.
fits any 11xx series brushless motor quad.
thingiverse
free
Valkyrie-250 quadcopter by dani1498
...-w32ch-transmission-wp-eu-965760.html)
for the look i took inspiration from the peon230 (http://www.thingiverse.com/thing:629338)
thingiverse
free
Brushless Prop Guard (1.9" Propeller) Stronger by Nico_FPV
... mcooz's mantis85 motor guard, but modified to clear 1.9" props.
will fit any 11xx series equipped brushless motor quad.
grabcad
free
Solar Bird - Flying Wing
...not included. you can download it separately from "https://grabcad.com/library/brushless-dc-bldc-motor-br2212-920kv-1".
thingiverse
free
Skyflex 2000 Triblade Propeller by tRubbelMaker
... last more than one flight.... let's see. as i'm writing its still printing (about 18h with support, brim and 80% infill)
thingiverse
free
Flying propeller by LaJulasse
...flying propeller by lajulasse thingiverse most similar toys have a common flaw: the propeller is 3d...
thingiverse
free
Prop guard for 1020 brushless motors with 70mm props by Painless360
...but gain a lot of extra protection for the props when flying indoors or in close proximity to things.
happy printing and flying!
Madr13D
thingiverse
free
KL-130_130mm_StreatchedSteppedX_MicroDrone by MadR13D
...t doesn't like such a big file. it, "camstudio", works fine when i do a little test clip. -soon hopefully.
peace!
thingiverse
free
Micro Drone Flight Controller Adapter 30mm to 20mm FC by MadR13D
... x 30mm mounting holes for the fc but mine is 20mm x 20mm.
just don't want to drill holes.
will test this very soon.
peace!
thingiverse
free
Micro Drone Flight Controller Adapter 20mm to 16mm FC by MadR13D
... it is set to print upside-down.
(or you could drill the holes to do without this extra weight.)
peace and happy and safe flying!
thingiverse
free
Maker Select V2 Mosfet (Minimal Magnet Mount) by MadR13D
...hotbed to high manually by mistake. it’s right underneath the extrude temp on the menu! how i fried my first main-board.
peace!
thingiverse
free
"Monarch 80" - 80mm Brushless Micro Drone by MadR13D
... eager to fly it!
i think its way on the heavy side for a 80mm micro at 80 something grams. what i still want to work on.
peace!